Search Documents

By GEORGE D. RAMSAY

ABOUT three miles west of Fontana San Bernardino County, California, and fifty miles east of Los Angeles, the Kaiser Co., Inc., has built an integrated steel plant. By integrated, I mean that from its wholly owned iron ore and coal supply, the Kaiser Co. is producing in its own mills iron and steel products. Pig iron to meet the West Coast needs has been produced at Fontana since Jan. 1, 1943; steel ingots were first poured there May 14, 1943; and steel plate for ships was first rolled Aug. 15, just sixteen months after ground was broken. Briefly, the plant consists of: (I) Two batteries of by-product coke ovens, totalling ninety ovens, carbonizing about 1740 tons of coal per day at capacity; with by-product facilities for the production of tar, ammonia, and ammonium suIphate, light oil distillates, and tar distillates. (2) One blast furnace producing at

Jan 1, 1944

By ELIHU THOMSON

IN 1877, Professor Thomson delivered at the Franklin Institute, [Philadelphia, five lectures on electricity. The object of the lectures and the demonstrations, which were numerous and many of them original even to the employment of special apparatus constructed by the lecturer, was to show clearly that electricity, of whatever name, was the same., differing only in tension (as it was termed) and in the current flowing, or quantity (the old term), in steadiness or in wave-like character. In those days, the textbooks divided the subject into statical and dynamic electricity, with sub-divisions such as frictional electricity, voltaic electricity, magneto electricity, electromagnetism, thermo electricity, and animal electricity. The well-known Ruhmkorff coil,' or spark coil as it is now called (as when used for the ignition of automobiles), was employed to step, up a battery current to a high-tension discharge which would charge condensers, such as Leyden jars.

Jan 1, 1921

By Arthur F. Wendt

The following experiments and researches were originally conducted by Dr. Heinrich Rcessler, chief of the German Gold and Silver Parting Establishment at Frankfort-on-the-Main, for the sole purpose of abating the nuisance created by the discharge into the air of the sulphurous and sulphuric acids generated in the process of parting bullion by sulphuric acid. The results achieved have, however, an important bearing not only on this process, but are of value in the manufacture of sulphuric acid and sulphate of copper from sulphurous gases derived from any source. It has now been in successful operation for a term of years at Dr. Roessler's own works, and has been lately introduced with satisfactory results at the royal mints of Kremnitz and Munich, and the well-known establishment of Johnson Mathey & Co., of London.

Jan 1, 1884

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By E. P. Polushkin

This work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility of determining the amount of the constituents without separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. Suppose Fig. 1 represents a part of a photomicrograph on which the total area of the black figures is to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively. This is also true for the whole area of the photomicrograph. Therefore, to determine the total areas of the black and white figures we must first find the proportion between the sums of the medians and then divide the area of the whole photomicrograph in the same proportion.

Jan 1, 1925

By R. Hadfield

Since the writer has been intimately connected with the development of manganese steel for many yearsm some remarks upon the early work wutg regard to the rolling and forging of the material might be of interest…

Jan 1, 1915

By Harold C. Price

One year ago, that is in January, 1923, there had not been constructed a single oil-storage tank of 55,000-bbl. or more capacity with a completely electric welded roof and bottom. Today, there are at least fifty 80,000-bbl. storage tanks completed, or nearing completion, on which both the roofs and the bottoms are electric welded. It is the purpose of this paper to describe, in a general way, the construction of these welded roofs and bottoms, and to give their advantages over riveted construction. All of the following data and conclusions were obtained from observations made during the welding of tanks by the Welding Engineering Co. at Texas City, Tex., and Tonkawa and Burbank, Okla. As far as can be determined, the first electric welding on large tankage was completed in May, 1922. At that time the Empire Companies of Bartlesville, Okla., discovered a badly leaking bottom in a 55,000-bbl. tank at El Dorado, Kans. They had considered concreting this bottom, but because of the much smaller cost, decided to try electric welding; so a contract was given the Welding Engineering Co. of Bartlesville, Okla. In this instance, no new sheets were added, the bottom being repaired by electric welding of all seams and rivets, Fig. 1. In some places where the original rivets were missing, the holes were filled by welding; patch plates were also added at certain badly worn spots. This tank has since been used for over a year and a half, but no other

Jan 1, 1924

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By T. A. Rickard

Do not write until you have something to say. Think first; then write. In order to be understood, you must know what you wish to say. Clear writing is the consequence of clear thinking. Therefore consider your subject well before you begin to write; ruminate on it; marshal the salient facts in your mind; saturate yourself with the ideas you wish to express and with cognate ideas; then express yourself deliberately. If you are bubbling over with your subject the words will come, but you might as well expect to sail without a breeze as hope to give life to words without the living thought. Here I may advert to the fact that among the uneducated it is a common expectation to acquire the knack of writing without taking the trouble to study the art of literature. I overheard a woman in a suburban train remark to her neighbor: "I'd like to be able to write well without stopping to think about it". She was one of many that would like to do a thing well without the trouble of thinking; but it cannot be done in respect of anything to which thought is essential. The possession of a good voice does not justify a person in expecting to sing successfully to a large audience; before singing in public one has to master the technique of singing; one has to learn first how to breathe properly, how to enunciate, and many other things. The successful singer is an artist, not a megaphone. Most of us would regard a man or a woman without any training in the art of singing as a fool or an impostor if he or she were to give a public concert, yet we do not recognize the equal foolishness and imposture of persons that write books before they have studied the technique of writing. That is why so many books are unreadable, and why many books by clever men are difficult to read. They start to write books before

Jan 1, 1931

By Leo Behr

RECENT years have seen important practical advances in the construction of recording instruments for use with thermocouples. The difficulties of the problem will be appreciated when it is remembered that a 10° F. change in temperature of a base-metal couple at 1500° means a change in the electromotive force of about 0.00035 volt. In a circuit having a resistance of 350 ohms, this means a change in the current of 0.00000,1 amp.; and despite this requirement of great sensitivity the instruments must be sufficiently robust to withstand the rough usage which is so often their lot. Two methods are in common use for the measurement of the electromotive force produced by a thermocouple: 1. The milliammeter method, in which the current produced by the thermocouple in a circuit of known resistance is measured and from. this the electromotive force is deduced by Ohm's law. 2. The potentiometer method in which a known potential difference is opposed to the thermocouple electromotive force. The use of thermocouple and milliammeter for measuring temperature introduces some possible sources of error, for the reading depends on a number of factors, including the following: (1) Electromotive force set up at the hot junction, (2) electromotive force set up at the cold junction, (3) resistance of the circuit including thermocouple, lead wires, and meter, (4) field strength of magnets, (5) strength of controlling springs in meter, (6) friction at pivots, of pointer on paper, etc. It is obviously necessary to so design and maintain the installation that the reading is independent of all the factors except the first. The electromotive force set up at the cold junction can easily be taken care of provided it is constant. This has been approximately accomplished by burying the cold junction in the ground or actually secured by locating it in a container, the temperature of which is kept constant by means of a thermostat.

Jan 9, 1919

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

By R. H. Swallow, George Hess

Aerial photography was once a crude, uncertain tool. Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques.

Jan 1, 1949

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

President Howe: It is, of course, not easy to discuss off-hand the paper which Mr. Becker has presented with so much lucidity. I will only make one remark, which is outside of the line of his argument, and concerns merely a passing allusion in his paper. Mr. Becker speaks of the fact that glass breaks with a flat or conchoidal fracture, and that steel shows a rough or " cupped " surface of frac-

Jan 1, 1895

By Anson Hayes, John Chipman

THE quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the British Iron and Steel Institute.1 From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. GENERAL THEORY OF SEGREGATION The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1938

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936