Search Documents

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

By Paul J. Sirkegian

A detail of the guide rollers is shown on Fig. I; and Fig. 2 shows a photograph of a guide roller that has been in service for several months on the haul-back cable. The former practice of supporting and guiding the haul-back cable on slusher hoists at Kimberly was accomplished by using the conventional type of snatch-block pulley, but it was found that an excessive amount of cable whipping and unreasonable wear on both rope and pulley resulted from this type of cable support. The guide, which is wholly made in the Corporation's shops, consists of two vertical and one horizontal roll assembled in a frame that is lagged to the cap timber in a slusher drift. In some slusher drifts more than one guide-roller assembly is used, depending upon the length of the drift. The installations usually are placed at 30-ft. intervals. We have found by actual experience that these rollers have increased the life of the haul-back cable approximately 200 per cent, as compared with the usage of the conventional sheave-block pulley. Cable Care The underground rigging crew and the slusher operators are trained in rope splicing. No cable clamps or knots are permitted on slusher cables and all cable "eyes" are spliced. The standard practice has been to use preformed cables of ?-in. diameter for haulage and ½-in. diameter for the haul back. The preformed cables have proved to be important factors for safety in use and speed in making splices. No external lubrication is used on the cables. It has been found that dry ropes have about 400 per cent longer life than those that were lubricated under these operating conditions. An accurate record is kept of all cable life and the tonnage moved by the slushers in each working place, and if the rope wear is excessive in any particular working place, an investigation is made to determine the reason. Wire-rope Sling for Snatch-block Anchor The rope sling is shown by Figs. 3 and 4. These slings support the snatch-block pulley for the haul-back rope. The standard practice at Kimberly is to use a roller-bearing snatch-block pulley 10 in. in diameter. The snatch-block housings are equipped with a clevis attachment in preference to swivel hooks, as it has been found that the more rigid clevis keeps the cable in better alignment. The snatch blocks are hung from the cable sling, which is wrapped around the posts of the drift sets as shown on Fig. 3. This method of anchoring the pulley provides better anchorage and flexibility than those of the rigid or spring-mounted types. When the slusher-drift headings are being advanced, the snatch blocks are hung from a "gin" pole ahead of the last set of timbers' An employee is assigned on each production shift to take care of the lubrication of all slusher hoists that are being used and he is provided with tools for minor repairs.

Jan 1, 1946

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- ' creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance' than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C'. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By G. L. Oldright, F. S. Wartman, H. E. Keyes

The economic manufacture of sulfuric acid by the ordinary chamber process usually involves production on a large scale and a plant that is costly to construct. The nature of sulfuric acid makes it costly to transport any great distance. For these reasons, the metallurgist has not found it feasible, at times, to beneficiate ores amenable to leaching, and a need exists for a local process that will produce acid cheaply on a small or large scale. To leach ores containing residual sulfides, an oxidizer, such as ferric sulfate, is needed in solution. Precipitation with scrap iron is one of the cheapest methods of removing some metals from solution, giving a plant of low first cost and supplying a source of cheap ferrous sulfate. The other ingredient needed for the process is SO2 roaster gas, the addition of which, as described below, will give both ferric sulfate and sulfuric acid. Where roaster gas is a waste or obnoxious product, the expense for materials is still further lessened. The use of ferric sulfate and sulfuric acid as a solvent lends itself well to the utilization of scrap iron as a precipitant, and the stages of the process fit in well together as an economic whole. Applications The hydrometallurgist usually thinks of ferric sulfate as a partial solvent for some of the sulfides of copper alone, as most work has been done on this metal. The processes of Hannay and Christensen, for leaching unroasted galena with ferric chloride made by anodic oxidation, show the added solvent action given by "ic" salts when added to brine solutions. It was found by R. D. Bradford (in some work to be published soon by the University of Utah) that, by the addition of a ferric salt to a brine solution, the silver as well as the lead in an unroasted semi-oxidized ore could be largely dissolved. The "ic" salt in the case of silver has evidently the same effect as the case of cupric sulfate when

Jan 1, 1926

By H. H. Kellogg

A model of the slag-fuming process for recovery of zinc oxide fume from lead blast furnace slags, adapted to solution by a digital computer, is presented. The model incorporates the variaticm with time of the following: the fuming of zinc and lead, the change in the ferrous-ferric ratio in the slag, the transfer of sulfur to and from the slag, the temperature of the liquid slag, the temperature of the gases and fume which exit to the flue, the heat losses to the water jackets, and the amount of frozen slag on the water jackets. The assumptions which underlie the model-some of which are but crude approximations—are discussed. Despite some obvious shortcomings, the model simulates faithfully many of the important features of practical slag-fuming operations. The behavior of the model is compared with the operation of the American Smelting and Refining Co. fumzace at El Paso, Tex. The model is used to predict the effects on performance of changes in the coal rate, the temperature of the secondary air, and the composition of the coal. THE fuming of lead blast furnace slag for recovery of zinc oxide is standard practice today, and it has been the subject of several previous attempts at mathematical process analysis.'-' The mathematical process model described in this paper incorporates many of the features from the earlier studies, but it is a far more complete and realistic representation of the commercial process in that the following additional features have been included: the fuming of lead as well as zinc; the transfer of sulfur between slag and gas; the addition of slag feed in batches, over a period of time; tapping of the final slag over a period of time; the change of slag temperature with time. The additional features of the present model add greatly to the mathematical complexity, but this difficulty has been obviated by programming the model for solution by a digital computer. The IBM 7094 computer solves the model for one operating cycle of the fuming furnace in less than 1 min. It is doubtful if the same calculations could be completed with the aid of a desk calculator in less than a month. The computer program, written in the Fortran IV language, is too lengthy for presentation here.* Instead, this paper As shown in the sections which follow, it does simulate with remarkable faithfulness most of the known behavior of the industrial process. On the other hand, the model contains several gross simplifications of both the chemistry and heat balance, necessitated by the lack of more exact knowledge. In addition to these known weaknesses, it is not unlikely that those more intimately acquainted with industrial practice than the author will find other additions to or modifications of the model which will improve its utility and reliability. CHEMISTRY In brief outline, the present model treats the fuming furnace as two units, A and B, in series. In A the batch of slag reacts with the continuous stream of air (primary and secondary) and fuel injected at the tuyeres, to produce a stream of hot, reduced gases containing zinc vapor. The zinc content of both the slag and the product gas changes with time because of the batch nature of the process. Unit A is called the "lower furnace" in this paper; physically, it is considered to be that part of the fuming furnace which lies below the charge port. In B, the "upper furnace", the product gas from A is burned with the stream of "tertiary" air, to produce zinc oxide fume. The performance of B also depends on time because of the time dependence inherited from the product gas of A. The rate behavior in the lower furnace determines the important features of the process—the rate of elimination of zinc and lead from the slag, and the amount of fuel required for this purpose. Bell, Turner, and peters' published the first useful model of the lower furnace. They employed the assumption that, at any instant of time, the slag and reduced gas reach a state of equilibrium, according to the reactions: They cited only indirect evidence in support of their assumption of slag-gas equilibrium, yet several more recent laboratory studies of the activity of zinc oxide in slags4-8 have produced evidence which supports their view. On first acquaintance it seems unlikely that a high-output "rate" process like slag fuming would even approach an equilibrium state. The author, in an earlier study,' established, however, that the gas-slag interface in a fuming furnace was capable of such high mass-transfer rates that a close approach to equilibrium between gas and slag was quite probable. In devising the present model it was decided to assume a state of equilibrium between slag and gas at the outset, and then to modify this assumption as necessary in order to make the model agree with the be -havior of the actual process. Up to this time the assumption remains a part of the model, since no behavior

Jan 1, 1968

By W. C. Elmore

THE magnetic powder method, long used for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By Robert Ammon

The purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 mm. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0 mm. 9. Remarks on the inner feed cone. In the following pages all overflows are given in quartz dimensions; i. e., by a 0.75-mm. overflow is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm. The development of the classifier was commenced in the fall of 1910,

Jan 1, 1914

By M. Kaufman, A. E. Palty

The phase structure and aging characteristics of two nickel-base alloys, Inconel 718 and 702, were investigated. Wrought and cast Inconel 718 showed ArisCb as the major hardening phase, as well as ture was positively identified. Inconel 702 had Ni3Al as the major hardening phase, as well as Cr7C3-of the phase amounts with temperature was determined. 1 HE value of phase structure and aging rate information in the utilization of alloys has been well established. As part of a continuing program, the results obtained on two nickel-base alloys, hconel 718 and Inconel 702, are presented here. Inconel 718 is a relatively new alloy considered for application in both sheet and cast form. Its novelty lies in the use of high columbium tantalum levels in a Ni-Cr-Fe base. No previous work on this type of alloy has been reported in the literature. Inconel 702 is being used now as an oxidation-resistant sheet alloy. Occasional fabrication problems spurred work on its basic structural behavior. The composition of 702 is essentially nichrome plus aluminum and titanium for strengthening and added oxidation resistance. This puts it in the basic class of other nickel-base alloys which have already been studied. The two alloys will be treated separately. INCONEL 718 Phase Study Methods. The phases present after the various conditions investigated were determined by X-ray diffraction analysis of two different elec-trolytically extracted residues and microscopic examination. The extraction methods, using 10 pct HC1 in alcohol and 10 pct H3PO, in water and the X-ray technique have been described previously.' The effect of temperature on the phase behavior was studied on sheet material using the following heat treatments: 2250°F, 2 hr, ice brine quench 1300 100 hr, water quench 2250°F, 2 hr, ice brine quench 1400°, 100 hr, water quench 2250°F, 2 hr, ice brine quench 1500°F, 100 hr, water quench 2250o 2 hr, ice brine quench 1700°F, 48 hr, water quench 2250°F, 2 hr, ice brine quench 1850°, 24 hr, water quench 2250°, 2 hr, ice brine quench 2000°F, 6 hr, water quench The high solution temperature was an attempt to dissolve as many phases as possible without causing melting. Aging exposures were made longer than normal heat treating times in order to approach equilibrium conditions more closely. Cast material was examined only in the as-cast condition and with the normal heat treatment (1700°F, 1 hr, air cool 1325oF, 16 hr,air cool). Materials. The full phase study was performed on sheet specimens approximately 1/2 in. by 2 in. by 1/16 in. The cast pieces were cut from the gating system of a vacuum-cast test piece. An all weld-metal specimen was made by running many weld beads on the sheet using filler made from the sheared edges of the sheet. All external contamination was removed by belt-sanding followed by an electro-polishing treatment. The typical composition of wrought Inco 718 is as follows: The alloy is air-melted. Cast hco 718 may have higher molybdenum. Due to the expectation of finding a Ni-Cb phase (Ni, Cb) for which no X-ray diffraction pattern was available in the ASTM Index, a special 5 Ib heat to the stoichiometric composition of this intermetallic

Jan 1, 1962

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By Carl Henrich

A.. S. DWIGHT, New York, N. Y.-Mr. Henrich's paper is rather inconclusive as to the role that alumina really plays in slags. He gives a number of interesting instances of high alumina, with conclusions that he draws from the analyses, in the light of what he knows of the accompanying conditions, but the information given is hardly sufficient to permit intelligent criticism of these conclusions, for it is well known that the slag composition is not the only factor that can produce some of the furnace results favorable or disastrous, as the case may be, which he records. As a matter of fact, most metallurgists who have wrestled with this problem in connection with the smelting of lead and copper ores, usually arrived at some sort of a working hypothesis which met the local conditions fairly well, and then, being busy men, were inclined 'to leave the theoretical question very much as Mr: Henrich leaves it when he says: "A question with which I purpose dealing at some future time." It is unfortunate that in the Golden Age of the smelting industry in the West, when we were all dealing with large tonnages of complex ores, often containing large percentages of alumina in combination with other. refractory elements, the smelting companies were not generally equipped for research as they are today, and much experience that might have been,

Jan 4, 1917

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By William Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to tem-perature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts.

Jan 1, 1935

By H. N. Wolcott

Among the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It seemed to the writer, therefore, that the case described below was worthy of record. Fig.1. GROUndALass of chalcopyrite (C) containing Rounded GRAINs of TYRITE (P) SHOWING DEFFERENT DEGREES OF REPLACEMENT BY QUARTZ (($), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town mine, in Russell, Gulch, and ;re in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy-rite. with some grains of tetrahediite. The polished surface of some of

Jan 1, 1918

By Martin C. Kuhn, Lawrence G. Stevens, J. Mark Richardson

The majority of the world's known and anticipated reserves of nickel ores are lateritic deposits At present, there are several different process alternatives for recovering nickel and other desired metal values from laterite ores An overview is given of the selective reduction roast/ammoniacal leach process, one of the processes in commercial operation.

Jan 1, 1981

By D. L. McCain

Slurry transportation of coarse coal from the mining face to the preparation plant has proved successful in a West Virginia underground mine. Coal has been pumped from the mining section for several months. The system is currently being provided with the flexible link to the face to allow for continuous transportation. Some future plans for coal mines and projections for broader applications of the transportation method are given.

Jan 1, 1976