Search Documents

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle coal at the rate of 200 tons a day. By 1860, revolving screens were in wide use in the Pennsylvania anthracite field. Shaking screens were introduced in the Pennsylvania anthracite region in the 90's and they rapidly displaced the lower-capacity revolving screens.

Jan 1, 1950

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By Charles S. Barrett, Robert F. Mehl

The system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that developed by Bijl l (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1930

By R. P. Rothwell

Instruction by correspondence is certainly one of the most important and useful of modern educational methods. The paper on the " Scranton International Schools," by Prof. Stoek (Buffalo meeting, October, 1898),* gives an elaborate description of a single private enterprise in this direction, ignoring all others, and cannot be said to present a fair or impartial view of

Jan 1, 1900

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole.

Jan 8, 1954

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955

Freeport's Floating Mine Begins Sulphur Operation Eight years of research were culminated when Freeport Sulphur Co.'s floating mine plant went into operation on Bay Ste. Elaine in the remote Louisiana bayou country 60 miles southwest of New Orleans.

Jan 1, 1953

By R. Crnojevich, J. L. Blanco, C. Nikolic, W. G. Sherwood

This paper describes the process used for cobalt purification and recovery at the AMAX Nickel Refining Co. plant In Port Nickel, Louisiana In the first stage, cobaltic precipitate produced in the Outokumpu electrolytic nickel cobalt separation process is dissolved using methanol and sulfuric acid liquor produced in this step is converted to an ammoniacal complex, and sufficient ammonium sulfate is added to facilitate cobalt oxidation to cobaltic pentammine Nickel is then selectively precipitated as nickel-ammonium sulfate double salt at pH 2 5 Final purification of the pentammine liquor is effected by pH adjustment with ammonia and removal of divalent nickel by ion exchange Purified liquor is then advanced to hydrogen reduction to produce cobalt metal Although similar to other cobalt refining processes used in the nickel industry, the Port Nickel process is unique because of a single point chemistry adjustment for a number of unit operations that occur in succession.

Jan 1, 1981

By W. Joseph Schlitt, Kenneth J. Richards, John D. Prater

Kennecott Minerals Company has developed a leach-hydrolysis route for treating flue dusts from copper smelters The flue dusts are acid leached in an oxygen atmosphere to solubilize copper and fix the arsenic, antimony, and bismuth as stable compounds Copper is recovered by cementation with Iron and the barren solution is recycled Molybdenum and other values may be recovered by modification of the basic flow sheet Results of bench scale and pilot plant tests are discussed in terms of the effect of operating parameters.

Jan 1, 1981

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By James A. Carney

The quality of water for steam boilers is a serious question in Illinois, and has been the occasion of many investigations, undertaken either for the discovery of sources of a better supply, or for the purification of the supplies already at hand. LOCATION OF SUPPLIES. The sources of supply of which this paper treats lie along the right of way of the Chicago, Burlington and Quincy Railroad Company, and form a nearly straight line from Chicago, Illinois, on Lake Michigan, to Burlington, Iowa, on the Mississippi River. The supplies consist of surface-, ground- and deep well-waters ; their locations are given in Fig. 1, which is adapted from a map of Illinois published by the Illinois Railroad Commissioners. The influence of the geological formation on the water-supply of Illinois is fully treated in an article in the Seventeenth Annual Report of the U. S. Geological Survey by Mr. Frank Leverett, entitled, " The Water-Resources of Illinois." It is not the purpose of this paper to introduce a geological discussion; and

Jan 1, 1898

By C. H. G. Bushell, M. Malnarich

Reagent control in flotation is more an art than a science. Operators vary the amount of re- agents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercorrection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment.

Jul 1, 1956

The Institute is custodian of -funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1938

By Melvin H. Podwysocki

Lineament and fracture analysis have enjoyed a resurgence of interest over the last several years, particularly since the advent of the Landsat series of Earth resources satellites. Some applications for lineament analysis include mineral, petroleum and ground- water exploration, engineering studies such as highway routing, mine roof stability, dam and power plant siting and general tectonic studies. The needs of each study may be different, but the general problem of large masses of data is common to all. Methods for efficient handling of the information and some statistical methods for its evaluation are discussed. These include comparing the lengths of the fracture population against known distributions, trend surface analysis of fracture lengths and number per unit area and multivariate analysis of rose diagrams. Examples are shown in an experimental program for predicting the presence of reef structures, areas of potential petroleum production.

Jan 1, 1977

By C. D. Henry, M. L. W. Jackson

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of state and federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1984

By Lauren A. Wright

The principal talc deposits in California are in a 200-mile belt paralleling the state's eastern border. The southernmost deposits represent selective alteration of early pre-Cambrian (?) carbonate strata, and are associated with granitic rocks. Deposits in the Death Valley area are at or near contacts between late pre-Cambrian carbonate rocks and diabase sills. Those in the Inyo Range area are chiefly alterations of Paleozoic carbonate rocks and silica rocks. Most of the state's talc output is used in ceramics.

Jan 1, 1950

By C. R. Pelley

This paper describes the analytical characteristics of Western subbituminous coal and the manner in which these characteristics apply to their use in a utility-sized steam generator. It compares these characteristics with those of typical Midwestern coal and Eastern bituminous coal. The paper also reviews in detail the design considerations that must receive attention when various blends of these three coals, or any combinations thereof, are planned to be used. This research paper describes variations in analytical and utilization characteristics when coals from different origins are blended in order to achieve a predetermined sulfur content for the purpose of predicting sulfur oxides emissions as they affect environmental regulations and the resulting alterations in utilization characteristics such blending would cause, and how such blends of coal would affect a utility-sized steam generator.

Jan 1, 1979

By John W. Straton

The President of the United States signed Public Law 91-173 on December 30, 1969 and the Federal Coal Mine Health and Safety Act of 1969 became law. The Bureau of Mines was required to promulgate regulations to implement the law. Unfortunately, some stipulations of the Act were not technologically possible. The USBM employed many new inspectors and had to instruct both old and new personnel in the requirements of the law. Mine operators and mine workers also had to be informed. There was a fair measure of inconsistency during this period. Progress is being made, however, and it is becoming easier for mining personnel to know what needs to be done. There are some unresolved questions, however, and there still appears to be an appreciable lack of uniformity in the application of the law by the many federal inspectors.

Jan 10, 1972