Search Documents

By H. R. Peiffer

Composite alloys of silver and alumina are shown to resist flow above the melting point of the continuous matrix. The ability to resist flow depends on the fineness of the dispersion and the oxygen content of the silver. It is believed that the oxygen influences very strongly the bond between the molten silver and the finely divided alumina. RECENT needs for materials with high strength and creep resistance at high temperatures initiated mechanical property studies on dispersed phase materials to near the melting point of the continuous matrix material. Results' of these investigations have shown that certain of these materials do have promise for high-temperature applications. Experiments performed on composite materials of silver and alumina by the author have resulted in the discovery of an interesting effect above the melting point of the silver. In these materials the silver was continuous and the alumina very finely divided (Linde B). It was observed that these materials exhibited strength and resistance to flow above the melting point of the silver matrix. The purpose of this paper will be to describe these properties. METHOD OF PREPARATION The materials were prepared by mixing the proper amount of Linde B alumina and high-purity silver oxide. The alumina content was varied from 5 to 20 wt pct alumina in silver in 5 pct steps. The materials were mixed by blending the constituents in an ordinary food blendor using ethyl alcohol as a vehicle. Enough alcohol was added to the powders to form a mixture with the consistency of a thin mud. After blending for about | hr the material was dried and the silver oxide reduced by heating to 450 OC. The material was then pressed at 25 tsi into a -in. billets 3 in. long. EXPERIMENTAL PROCEDURE The specimens were horizontally supported at either end by knife edge supports of cold-rolled steel. This holder was then placed in a "globar" furnace and a chromel-alumel thermocouple placed very close to the specimen recorded its temperature to within 10°C. Each specimen was heated rapidly to 900°C initially. The specimens were held at temperature approximately 30 min and then the temperature was raised 50 deg. The procedure was repeated until deformation was noted. Photographs were made of the specimens at various temperatures and increments of time using a Polaroid Land camera. RESULTS Fig. 1 shows the 5 pct by weight "Linde B" alumina and silver material after reaching 980 °C. Failure occurred after 15 min at this temperature. There were two points of failure and silver collected at them. No additional flow of the molten silver was noted at any other place. Fig. 2 shows a 20 pct by weight "Linde B" alumina in silver specimen. After 30 min at 1400°C, bowing of this material was observed. Other concentrations of alumina were added to

Jan 1, 1961

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

By Frank E. Shepard

Electric power in mining-operations is now successfully applied to haulage, hoisting, lighting and pumping; and until lately, drilling was the one department of mining in which an electric source of energy had not been introduced. Drilling by electric power has been the field for much investigation and several forms of electric-drills have been tried; but in the severe service of rock-drilling many dieculties have been encountered, and the heavy cost of repairs has caused a deep prejudice against this system of drilling. In the majority of electric rock-drills previously placed on the market, two principal factors have been considered; first, a portable electric motor usually of heavy pattern, coupled to the driving-mechanism of the drill proper by means of a flexible shaft; and second, the coupling of some form of reciprocating cross-head to a piston by means of a spiral spring, the drill-bit being fastened to the piston-rod by some suitable form of chuck with fastening bolts and nuts. In this latter form of drill, the cross-head has a fixed stroke, while the piston with drill-bit attached is allowed a variable stroke through the

Jan 1, 1904

By L. C. Uren

Some of US have been impressed with the need for a better understanding of the future place of the engineer in the petroleum industry. In academic work we are continually asked to advise students as to the opportunities in different directions, to guide them in their selection of professions, and it would be extremely helpful to those in academic lines of work to have the opinion of engineers from the industry relative to the need for petroleum engineers. IS the industry going to require a continually growing number of engineers in the future years, or have we perhaps reached equilibrium in that regard ? In anticipation of this meeting, I undertook to canvass opinion among a number of engineers of my acquaintance and I have been rather astonished to learn that the expenditure on engineering salaries in the producing branch of the oil industry is extremely low. I have figures from eight or 10 of the larger oil companies and it seems to be a fair statement on the basis of these figures to say that the average American oil company is devoting less than 2 per cent. of its gross expenditures in oil production to the payment of engineering salaries. A few examples will be of interest. I shall not mention names of individual companies, but one large Mid-Continent company is spending slightly less than 1 per cent. of its gross expenditure—that is, less than 1 per cent. of the total expenditure in the producing department—on engineering salaries and about as much on engineering research, which might properly be regarded as a phase of its engineering work. Another Mid-Continent company is spending about 11/4 per cent. on engineering salaries. A large California company is spending about l1/2 per cent. The largest figure that has come to my attention is that of an important Rocky Mountain and Mid-Continent company that is spending a little more than 6 per cent., but that is apparently an extreme case. The petroleum producing industry is a highly technical business in these days. It is spending in excess of $500,000,000 annually in new

Jan 1, 1929

By Harry T. Davis, Jasper L. Stuckley

The object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which—the Hot Springs and Kings Mountain —contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3½ miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite—usually there have been less than three producers—and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926. Geology of the Barite Areas In the Hot Springs area barite is found in the Max Patch granite of Archean age and the Snowbird formation of Cambrian age. The Max Patch granite is of two varieties, one gray to whitish and the other red. The gray granite is coarse, at times porphyritic, and composed of quartz, orthoclase and plagioclase feldspar, with a little biotite and muscovite. The red granite is also coarse and differs from the other only in having conspicuous pink and red feldspar. Both varieties have been much metamorphosed and weathered in places, so that they contain secondary

Jan 1, 1935

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By T. W. Guy

DuRing recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures. Early Cleaning Methods In the early days, the tipples were simple wooden structures, with bar screens for separating the fines from the lump coal. All cleaning was done by the miners at the face, or by pickers in the railroad cars. Gates were provided in the chutes by which the flow of coal could be stopped when necessary while the pickers raked the surface of the coal in the car and picked out the impurities. A large percentage of the fine coal or slack was used for making coke at the mines in beehive ovens. The

Jan 1, 1932

By John Jermain Porter

PAGE. I. INtroduction............ 191 I1. Derivation of Formula foR Fuel-RequiRements.... 192 1. Heat Available in the Hearth........193 a. Method of Calculation..193 b. Data for the Determination of Critical Temperature.. 195 2. Heat Necessary in the Hearth ...... 197 a. To Care for Slag..197 b. To Care for Pig-Iron...198 c. To Reduce Silicon........198 d. For Other Items.........199 3. The Effects of Rate of Driving ..... 199 4. Loss of Carbon Between Throat and Hearth.....201 a. Solubility of Coke..201 b. Carbon-Loss Due to Flux....201 c. Effects of Reducibility of Ore..202 5. The Formula as Used........203 III. The LImitations of the Formula........ 204 1. Through Effects of Irregular Furnace-Work.....204 2. Through Ratio Between Heat-Requirements in Shaft and Hearth. 20.5 IV. The Formula Applied to Actual Furnace-Records,.. 209 1. Description of Furnace-Stock........ 209 2. Furnace Dam..........210 3. Application of Formula..211 4. Average Furnace-Practice..213 V. Sources of Error........... 214 VI. SuggesTions for Practical Methods of Fuel-Economy... 215 VII. Efficiency as a Factor in Furnace-Management.... 219 1. The Efficiency Principle........ 219 2. The Application to the Blast-Furnace..220 I. Introduction. The heat-balance of the blast-furnace has been a favorite subject for discussion for many years. and its study has contributed much to our knowledge. and still possesses a certain academic interest. As a means of accounting for differences in fuel-consumption, however. it has failed utterly. and it is evident that we must look elsewhere for the means of accomplishing this end.

Jan 1, 1912

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By H. W. Graham

AS these annual occasions in honor of Henry Marion Howe continue through the years: there is progressively less likelihood that the lecturer will have had personal knowledge of Dr. Howe. The present speaker is one of those who unfortunately had no opportunity to come under the inspiring presence of this great metallurgist. A review of Howe's work shows it to cover a comprehensive range of interests and to evidence an impressive richness of detail. Not only was Howe at home in the laboratory, but he was familiar with the processes of iron and steel making and had a real understanding of them. His writings include much that is descriptive of processes with a wealth of material that is becoming of increasing historical value. He recorded his studies of the theoretical aspects of processes and published at least two process classifications, one in 1890 that was lengthy and somewhat theoretical, and a second in 1906 that was more of a practical listing. Wide as Howe's field of interest was, it is significant of the circumstances of his time that he gave- little consideration to raw materials or to their effect on iron and steel making processes. In 1933, Waterhouse, Howe lecturer for that year, presented a descriptive summary of the major steel making processes, and in 1946 Joseph discussed the blast furnace process. Otherwise Howe lectures have not dealt with processes as major subjects. In today's lecture, with no effort to describe the mechanical arrangements of iron and steel making facilities, it is proposed to examine the essential technological elements of the processes, to explore the inter-relation of these elements, and particularly to seek recognition and understanding of those factors which determine why certain processes are or are not used. The discussion of this lecture will deal with the major well-known large tonnage processes, with only such attention to processes of minor tonnage and special character as may be warranted for explanation by contrast. Subject to the errors of generalization and the shortcomings of condensation involved in presentation limited to a single hour, it is proposed to examine broadly but intensively those operations which convert raw materials into steel. It is an innovation for a Howe lecturer to discuss the raw materials of the iron and steel industry, but the changing circumstances of passing years intensify the influence of raw materials on processes and require the metallurgist to be alert for the process adjustments that may become advisable or mandatory. For a half century the metallurgical processing of iron and steel has followed a surprisingly straight path, but this does not necessarily mean that there are no curves in the road ahead. Ages ago primitive man came to know iron in its metallic form, not only by the

Jan 1, 1948

By John A. Brown

Granules are used primarily as roofing material. From the earliest times, man has been faced with the basic problem of providing protection for himself, his family, and his property against the ravages of the weather. Basically, this problem is no different today than in the past, except that today the trend is to demand shelter which is also colorful and distinctive. There has been a gradual evolution from the thatched roof to the modem ranchstyle home. In his search for a more permanent and more attractive roof, the home owner has utilized many mineral materials. All granules, whether slate or colored granules, are referred to by the asphalt roofing industry as "Slate Granules." Early Roofing Materials The development of mineral roofing in the United States followed two trends: first, the slate industry, and second, the bituminous products. The early colonists were familiar with slab slate construction from Europe and it was natural for them to continue with this type of roofing. As early as 1780, the forerunners of the present bituminous products were finding favor. Those early products consisted of saturating burlap or similar material with crude tar or pitch. This type of roofing was soon improved by dusting a variety of materials on the surface of the roofing to prevent adhesion while in rolls. Such factors as fire resistance and protection from the actinic rays of the sun soon followed. This started the general pattern which is still followed today, that is, saturating felt materials and supplying a uniform grade of crushed mineral to the surface. In commercial and public buildings, metal roofs found early favor. The attractive green color of verdigris-coated copper became a symbol of churches and institutions of learning. Aluminum roofing has become economical for large structures and is finding limited popularity in rural areas. Tile, asbestos, and cement materials, being weather resistant, found early acclaim and are still popular. Today, by far the most widely used roofing materials in the United States are asphalt products. Two important characteristics-economy and weatherability-account for their popularity. Influence of Building Trends on Roofing The postwar building boom in 1947 had many attractive features for the American people. The ranch-style one story type of home seemed well suited for suburban developments which sprang up in such profusion. As the roof in modern home construction is one of the most conspicuous aspects of its architecture, the home owner could now express his tastes not only in paint and landscaping, but could also select an attractive and harmonious roof color. Variety of Minerals Used Many naturally occurring minerals are used today in the roofing industry. Most widely used (and most noticeable to the public) is the granulated mineral surfacing applied to asphalt products. Selected natural colored granules as well as artificially colored granules are

Jan 1, 1960

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

By Carl E. Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. CHARACTERISTICS AND REQUIREMENTS OF SOLDERS IN GENERAL General Physical Properties.-When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.-The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

Jan 1, 1928

By Richard J. Gonzalez

The petroleum industry includes varied and extensive operations required to supply increasing quantities of refined petroleum products and natural gas that are essential for the economic progress of an expanding population Petroleum has provided the power for the transformation from the "horse and buggy days" to the age of jets and space exploration, and for the remarkable improvement in productivity per worker in agriculture and manufacturing. Without increasing quantities of oil and gas, the world would face painful readjustments to more expensive forms of energy and lower standards of living Petroleum operations start with exploration, development, and production activities that supply the basic crude oil and natural gas Pipelines, ships, barges, and trucks first transport the raw materials to processing centers and then move the finished products to the ultimate consumers. Processing plants extract liquids from natural gas and refineries convert crude oil into a wide range of products These products include transportation fuels, feedstocks for conversion into numerous products (such as fabrics, rubber, and plastics), light fuels for heating, lubricants, and heavy residual materials (industrial fuel oil, asphalt, and coke) The final activity of wholesale distribution and retail marketing moves products into millions of homes, farms, industrial plants, and motor vehicles The use of coal exceeded that of oil and gas until 1946 in the United States and until 1968 in the rest of the world. However, oil and gas have proved to be such convenient and attractively priced fuels that they now supply three-fourths of the total commercial energy (including coal, hydroelectric, and nuclear power) used in North America and more than one-half in the rest of the world. LARGE SCALE OF OPERATIONS By the beginning of 1970, world crude oil production exceeded 43 million bbl daily, -equivalent to more than 2200 million tpy In addition, natural gas and the liquids recovered from processing natural gas supply about 40% as much energy as crude oil Production of oil and gas provide by far the highest value of all mining operations. In the United States, the value of oil and gas production in 1969 of $13 8 billion exceeded the $13 0 billion value for all other minerals The rate of expansion in use of petroleum has been extremely rapid since World War II World crude oil production doubled from 7,500,000 bbl daily in 1946 to more than 15,000,000 bbl daily by 1955 It doubled again to 30,000,000 by 1965, and will double again by 1975 The use of natural gas has increased greatly in the United States and also in Europe, as important discoveries in the Netherlands and the North Sea and technology for moving liquefied natural gas from Africa provided attractively priced supplies

Jan 1, 1976

By Thomas Darlington

THE obligation of an employer to the State requires certain things of him as matters of good citizenship: for instance, that his workmen shall have a living wage, that child labor shall not be employed, that injuries from accidents shall not- make workmen a charge upon the State, and that the laborer's children shall have opportunity for education and to become good and useful citizens. Affairs of this kind are not taken up as philanthropy, for the officials of a corporation or a large manufacturing concern may not feel at liberty to spend the funds of their company as prompted simply by motives of kindliness; but they may spend company money on such matters because it is good business. For years, the poisonous effects of lead, phosphorus and dust have been emphasized in books on industrial hygiene and their elimination has been urged; but the more important and everyday physiology of the workman himself has been neglected. Part of my object in writing this paper is to show how our knowledge of physiology may be applied to working conditions in everyday life. In the interest of industrial laborers, accident compensation laws have been enacted in 33 States. This has been carried forward rapidly, because it has been shown that it pays both employer and employee. A further step is the recognition of sickness and disablement independent of accidents, not only because of their immediate cost to the worker and to the employer, but because continued efficiency in work and business depends largely upon health. Some measure of the importance of health in industry can be gained by the knowledge that records kept by some companies which now make this the subject of careful inquiry show that the time lost by employees, through illness; is several times as much as that lost as the result of industrial accidents. It is true that accidents frequently result in permanent disability or death, but it is equally true that illness is also a cause of permanent disablement or death. Thus the chief difference is that the loss to the employee through accidents occurring in the course of his employment is now generally recognized as a cost

Jan 2, 1918

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By Ralph C. Holmer

IN the field of mineral exploration, 1956 can be looked upon as the International Geochemical Year. This is not because of unusual developments in geochemical prospecting but rather because of the world-wide effort in geochemistry and the realization that geochemistry is now an established exploration method. Use of mining geophysics has continued to increase. Those extensively employing exploration techniques indicate that developments of the past few years have permitted better programming of methods, from reconnaissance to location of drill- holes. There is greater diversification of methods- reliance is not placed on results of one. However, it is realized that often it is more economical to drill an anomaly than to conduct additional expensive geophysical surveys

Jan 2, 1957

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947