Search Documents

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

By S. F. Ramseyer, E. A. Steigerwald

INFILTRATED structures represent composite materials which are capable of combining high-temperature strength with adequate low-temperature toughness and thermal shock resistance. Although copper- and silver-infiltrated tungsten structures are actually being used in rocket nozzle hardware, adequate understanding of the fracture mechanics of these composite systems is not available. Specifically the relative importance of the strength, ductility, and modulus of the infiltrant in determining composite properties is not known to the extent that optimum composites can be selected. The major portion of experimental effort in the area of composite strength has been devoted to fiber-reinforced systems1 or to systems where a discontinuous phase is imbedded in a relatively ductile matrix.2'3 In the case of high-temperature systems, which are composed of a relatively brittle matrix, such as tungsten or an oxide, a continuous phase exists for the propagation of a crack. The method by which the presence of a conjugate ductile continuous phase influences the gross properties of the composite represents an area which requires further investigation. This technical note presents results which evaluate the effect of infiltrant strength on the strength of the tungsten-base composite. A tungsten matrix and copper-base infiltrant were selected for the initial studies because of the ease of fabrication. Tungsten structures with nominally 20 and 30 pct porosity were evaluated. The porosity was controlled by varying the initial powder size and a ratio of open-to-total porosity greater than 95 pct was obtained by selective sintering cycles. The processing sequence involved hydrostatic pressing followed by a 72-hr presinter in hydrogen at 2000° F and a final sinter at 4000°F for 4 hr in vacuum. The 20 pct porous structure was obtained

Jan 1, 1965

By J. McD. Porter

In many of the old placer-mining districts are still to be found large tracts of gold-bearing gravel not suitable to be worked with a dredge, because the bed is too shallow or the gulch too narrow. Frequently there is not enough grade to handle the gravel successfully by ground-sluicing or a bedrock flume, or it contains too many boulders to be worked succeeefully with the ordinary hydraulic pipe or tube elevator. In southwestern Oregon, two practical placer-miners named Ruble, after working for years trying to make money out of placer-ground coutaining many large boulders, invented and patented a hydraulic elevator of an entirely new type, and one that has been found to work very successfully in flat ground and in gravel containing many large boulders. It is a very simple contrivance. A few years ago I acquired the property near Pierce City, Idaho, known as the American placer-mine. Various attempts had been made to work this ground. A bed-rock flume had been installed by one company, an Evans elevator by another, and still other methods were tried on a smaller scale. All were

Jan 1, 1910

By William G. Schultz

Sylvite’s potash mine probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hr production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tph. The ore is produced by two Marietta miners weighing 258 tons, making them the largest and heaviest piece of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000 ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground.

Jan 7, 1972

By M. F. Goudge

Production of many industrial minerals reached all-time records in 1965. In keeping with the high level of industrial activity throughout the nation, producers of many industrial minerals operated at capacity or near capacity, notably the producers of phosphate, potash and sulfur. In the case of sulfur, the demand exceeded production and orders were filled, in part, from stocks accumulated in previous years. Industrial minerals as a group continued to increase both in value and quantity at a faster percentage rate than metallic minerals and fuels, The U.S. Bureau of Mines estimated that the value of industrial minerals produced in 1963 was $4318 million vs. $2006 million for metals. Preliminary estimates for 1965 indicate that current value of production was again more than 2% times that of metals, thus making apparent their importance to the industrial life of the nation.

Jan 2, 1966

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By Robert H. Dickson

Limestone replacement and contact metamorphic orebodies are 80 irregular that sampling and estimating are far less. exact than in more regular types of deposits; both the mineralized masses and the lenses of ore within them are extremely irregular. So much development work is required to find the ore that the expense of blocking out great tonnages is prohibitive; furthermore, the rock near these orebodies is so heavy that drifts or raises cannot be kept open for many years without excessive repairs. As a result, few mines in limestone have more than three years supply of ore in sight. As most of the ore, is developed by stoping— not by drifting, raising, or drilling—estimates of ore developed do not indicate the total amount of ore that may be expected; they simply indicate the relative condition of the mines. But even if they are to do this, they must be made according to a fixed plan, intelligently carried out. The estimates of ore in the Calumet & Arizona Copper mines, Warren District, Ariz., have been of much value to those who plan the mining and development work. This paper describes the methods of sampling and estimating used in these mines. Sampling Samples are taken in various ways and depend on the condition of the working and the purpose for which the sample is to be used. Drifts, crosscuts, and raises are sampled by channels or by taking a grab off each mine car as it is filled. Stopes are usually sampled by drill holes or by taking a representative sample off each mine car; the latter, or chute, sample is by far the best sample. All workings are studied periodically by an engineer, who makes graphic and detail notes of the geologic structure, as shown in Fig. 1. The daily car tally and assay of each particular working is added to the same sheet opposite the material it represents. These sheets make a permanent record, showing the exact boundaries as well as the grade of ore in all workings.

Jan 1, 1925

By Joseph Richards

THERE are two essentially different types of case-hardening processes; that using a dry mixture in which the object to be case-hardened is packed and kept for the necessary time at the necessary temperature, and the "liquid" process, employing a bath of fused, salts into which the object- is immersed and which by immediate contact case-hardens the surface of the article. The Shimer process belongs to the second class, and was a war emergency invention. Of the liquid melts used as baths, the most effective and most fre¬quently used are melted potassium cyanide and melted sodium cyanide. These may be used either pure, or mixed with salts that reduce the melting point and the percentage of cyanide present. The use of these baths since 1914 has met many commercial difficulties because of the high price and frequent commercial scarcity of the cyanide salts; at present sodium cyanide has practically entirely displaced potassium cyanide. Another trouble is the danger to the workmen handling the cyanide salts, which are extremely poisonous, and the annoying and poisonous vapors or gases given off in the workshop, unless an effective system of hoods and ventilation is provided, so as to prevent the gases from the baths mixing with the air of the room. Porter W. Shimer, of Easton, Pa., has invented a substitute for the bath of melted cyanides which case-hardens with equal or greater facility and effectiveness, gives off no poisonous vapors, and costs for chemicals materially less than the cyanide costs in the previously used baths. The process has been in use over a year in a large American works and the following statement embodies the results of practical experience in the use and operation of the process. The Shinier liquid or melted bath consists of a mixture of easily fusible salts that do not possess case-hardening properties, into which is immersed fresh calcium cyanamide, which imparts to the bath case-hardening properties. The composition of the non-case-hardening-,salts appears rather immaterial. Good results have been obtained by using a mixture of sodium chloride, calcium chloride, and barium chloride in

Jan 2, 1919

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920

By John Chapman, J. C. Vaughan

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By William E. Ford, Edward Salisbury Dana

The NATIVE ELEMENTS are divided into the two distinct sections of the Metals and the Non-metals, and these are connected by the transition class of the Semi-metals. The distinction between them as regards physical characters and chemical relations has already been given (Art. 453). The only non-metals present among minerals are carbon, sulphur, and selenium; the last, in one of its allotropic forms, is closely related to the semi-metal tellurium. The native semi-metals form a distinct group by themselves, since all crystallize in the rhombohedra1 class of the hexagonal system with a fundamental angle differing only a few degrees from 90°, as shown in the following list :

Jan 1, 1922

By Alfred Wandke

The problem of vein formation has been of particular interest to the writer for years. As his work for a long time was confined largely to districts showing large deposits of copper ore, it was natural that the efficiency of replacement, as one if not the chief control of the emplacement of the ore, seemed a particularly attractive hypothesis. Of late years, in almost daily underground work in the Guanajuato district, he has collected evidence which makes it certain that in a number of cases the ore solutions were under sufficient pressure to force the rock walls apart and to hold them apart, thus offering an open space for the deposition of vein and ore-bearing material. This paper will concern itself with conditions frequently met with in hypogene ore deposits of the vein type, and will deal in particular with ore occurrence in precious-metal veins of the type classified by Lindgrenl as epithermal deposits, or metalliferous deposits formed near the surface by ascending thermal waters2 and in genetic connection with igneous rocks. To account for the emplacement of this type of ore deposit various writers have suggested the following agencies: 1. Shattering of the wall rocks. 2. Pressure of growing crystals. 3. Magmation, as treated at length by Spurr3. 4. Replacement. 5. Openings produced by folding. 6. Shearing due to gravity. 7. Shrinkage produced by the passage of pre-ore solutions. 8. Contraction joints produced by lateral secretion. To this list there may be added another agency, a discussion of which forms the basis of this paper: 9. Pressure of the ore-bearing solutions.

Jan 1, 1931

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A' of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A') and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A'. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By Frank W. Cramer

THE operator's panel is the control center f or the operation of the electric-arc furnace. It contains the switches and meters that control and indicate the power supply and in a way gives a picture of what is going on during the meltdown and refining periods. Regardless of manufacture, these panels are very similar with respect to equipment and position of apparatus. A typical panel is shown in Fig I. The three lights at the top of the panel are connected from the electrodes to ground and give a visual measure of the voltage across each arc. The ammeters underneath the lights show the current passing through each electrode. Directly underneath are the voltmeter, the watt-hour meter and the wattmeter and under these the three current-adjusting rheostats. In the center of the panel is the master electrode-control switch, which controls the movement of all three electrodes, with the individual electrode-control switches directly underneath. Next from left to right is the six-position voltmeter switch, which can be positioned to show on the voltmeter above the voltage between phases and to ground, the tap-changer switch with its indicating lights, and the main circuit-breaker control switch.

Jan 1, 1947

By J. C. Vaughan, John Chapman

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By H. A. Dierks

PENNSYLVANIA's anthracite region lies in the heart of the richest and most densely populated area of the U. S. Nearly 70 million people live within a radius of 500 miles, in which 130,000 manufacturing plants employ more than 8 million workers. The region comprises some 3000 sq miles and contains 484 sq miles of coal measures, which folding and erosion have divided into four separate and distinct fields, known as the Northern, Eastern Middle, Western Middle, and Southern. One million people live in the anthracite region proper, and their prosperity depends to a great extent on the anthracite industry, which produces more than $200 million in new wealth for the U. S. each year. Nearly 80 pct of the tonnage shipped out of the region is handled by nine railroads, which depend on this traffic for a large part of their revenue. It follows that the economic health and the very existence 0: this industry is of real concern not only to the region itself but also to the state of Pennsylvania and the country as a whole. Anthracite mining is one of the oldest mineral industries in America. About 1760 burning rock or stone coal was discovered on the hillsides of northeastern Pennsylvania. Within a few years a systematic search for coal bed outcrops was under way, and hand mining was begun. At first production was very limited, since anthracite was difficult to burn and was not readily accepted as a fuel. Pennsylvania anthracite is one of the densest and hardest of all coals, and its content of volatile matter is low. Consequently it does not ignite easily and it burns without smoke. About 1808 Judge Fell of Wilkes-Barre burned anthracite in an open grate fireplace and demonstrated proper handling of an anthracite fire. From

Jan 1, 1958

By S. Frederick Ravitz, Kenneth E. Fisher

Four liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constituents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equilibrium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest. In order to ascertain whether equilibrium existed, the distribution of gold and silver among the four liquids was determined. The speiss,

Jan 1, 1937

By A. S. Richardson

VENTILATION of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air- conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust- prevention measures that have been developed comparatively recently. FACILITATING FLOW OF AIR As a basic requirement for the safety of the men, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft is available as a base for fire-fighting operations. Control of the direction of air flow is

Jan 1, 1938

By Stanley D. Michaelson

Stanley D. Michaelson retired in 1976 as chief engineer, Metal Mining Div. and director of the Engineering Center for Kennecott Copper Corp. An active consultant on mining and metallurgical assignments, Mr. Michaelson is also currently adjunct professor of mining engineering at the University of Utah. He received his B.S. degree in mining engineering from Lehigh University in 1934 and an honorary E.M. degree from the Montana School of Mines in 1961. Mr. Michaelson received AIME's Robert H. Richards Award in 1962 and was named a Distinguished Member of the Society of Mining Engineers of AIME in 1975. He has served as a Director and as a Vice-President on the AIME Board of Directors and is a Past President of the Society of Mining Engineers. He became an Honorary Member of AIME in 1978.

Jan 1, 1979

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the 'underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972