Search Documents

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By R. M. Brick, M. A. Williamson

CERTAIN features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difference in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and 90°, as compared with drawn brasses, at 45°, for all compositions between 90-10 and 70-30.4 Data on individual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 EXPERITMENTAL METHODS The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per. cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 brass. Sections ¼ in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled-i.e., turned through 90 for each pass-and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained:

Jan 1, 1941

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.&apos;-&apos; In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure&apos; was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;&apos; however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954

By E. G. Woodruff

Few authors of treatises and papers on engineering subjects hare given adequate attention to topographic maps. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, means a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of map is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact,. the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. Since the maps have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth&apos;s surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 1, 1914

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would require too much space. The remainder of this discussion, therefore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. GEOLOGY The first, from the historical view, is geology in its relation to the mineral industries. Previous chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering so overlapped one another that men who were by, training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in geology as a pure science, and who perhaps took a doctor&apos;s degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would- not be questioned, even though they did not take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly 100 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson&apos;s X-ray data indicate that this decomposition is accompanied by a change in volume of as much as 5 per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson&apos; found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter5 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to 90 per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced 90 per cent when forged to ½ -in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By F. M. Lewis, J. E. Goodman

A larger, slow-speed, under-loaded ball mill and hydraulic classifier have almost doubled grinding efficiency at the lsabella mill. TENNESSEE Copper Co. operates two ore con-A centrators, the London and Isabella mills near Copperhill, Tenn. In 1948 and 1949 the small ball mills and rake classifiers in the London concentrator were replaced by one large ball mill and one hydraulic classifier. This new ball mill was designed oversize so that it could be operated at slower than normal speed. The proper operating conditions were established and the results published.&apos; Later it was found that this mill operated more efficiently with a small ball charge." While this London grinding practice was being developed, the Isabella grinding circuit was not changed in any way. It remained a conventional two-stage rod mill—ball mill combination, the rod mill in open circuit and the ball mill in closed circuit with a rake classifier. Study of the data indicated that grinding cost could be lowered by converting to the London practice, but not enough would have been saved to warrant the expense of converting. No plan for improving this grinding operation could be developed. In 1953 this study was reopened when plans were made to increase the Isabella mill output from 1150 to 1500 tpd. At this time the grinding circuit consisted of a 6x12 rod mill followed by a 6x12 ball mill in closed circuit with a 6-ft rake classifier. Another 6x12 ball mill and 6-ft rake classifier would have been sufficient equipment and would have been the simplest and cheapest installation. However, this would have offered no improvement in grinding efficiency or operating cost. If, on the other hand, the grinding operation could be converted to the London practice, by installation of one large 101/2x9x9 tricone mill and a 10-ft hydroscillator,2 lower operating costs would justify the additional investment. Economics: Table I presents estimates for the two schemes for enlarging the Isabella mill. In the first scheme, column 1, one 6x12 ball mill and one 6-ft rake classifier were to be added. In the second scheme, column 2, the existing small ball mill and rake classifier were to be retired and one large mill and hydroscillator were to be installed. Estimated savings from the difference in operating costs made an attractive return on the additional investment for the large mill and hydroscillator. Actual costs of carrying out this plan are tabulated in column 3b. It will be seen that these costs follow the estimates in column 3a very Closely. The return on the additional investment is calculated from the difference in the operating cost in column 1 and the actual operating cost in column 3b. This too come very close to the estimate. Power and Steel: Power requirements and steel consumption for the rod mills and ball mills, both actual and estimated, are presented in Table 11.

Jan 1, 1958

By W. A. Schaeffer, M. Albertson

The Yates field is situated in northeastern Pecos County, Texas. Its productive area is about 15,000 acres. Production is chiefly from limestone of Permian age. Depths of wells vary from 1100 to 1800 ft. Initial productions range from a few barrels to 8000 bbl. per hour. The field outlet has always been prorated. Gas-oil ratios originally varied from less than 100 cu. ft. up to 8000 cu. ft. per barrel at allowable production rates. The average ratio was about 500 cu. ft. Fig. 1 shows the structure of the field and the location of the Tippett lease, on which the original experimental tubing work was done. Before the latter part of the year 1929, little actual effort in practice had been given to determination of the conditions under which the highest efficiencies may be realized in naturally flowing wells. For the preceding few years attention had been given to gas-oil ratios and their possible reduction by maintenance of back-pressure by choking at the well head. Some attempts had been made toward reduction of ratio by bottom-hole choking. In late 1929, the Shell Petroleum Corp. started the experimental installation of specially designed flow columns adapted to high-pressure flowing conditions in the Yates field. The objectives in view were the attainment of low gas-oil ratios at low rates of flow and the maintenance of high bottom-hole pressures. All naturally flowing wells should be provided with a suitable eductor string immediately upon completion of the well, so that the benefits of efficient flow will be derived from the beginning. This paper presents a method of tubing for efficient flow and a discussion of some complex factors which influence well behavior. Factors Influencing Gas-oil Ratios Many factors influence the production of gas from naturally flowing wells. The writers believe that in some instances gas control is effected mainly in the reservoir itself, in others in the well bore, and in still others both sets of factors may be significant. Some wells apparently have penetrated productive zones in which practically all of the gas is closely associated with, and mostly dissolved

Jan 1, 1932

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By J. B. Austin, H. H. Pierce

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,&apos; using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By F. M. Hamilton, H. F. Ameen

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By John D. Meahin

THE use of digital methods for generating crystallo-graphic data is well-established and many programs are now available. Transmission electron microscopy usually requires a knowledge of the electron diffraction pattern which is obtained by plotting a planar section through reciprocal space. With cubic symmetry these sections are very easily produced, but with hexagonal and lower symmetry systems considerably more labor is involved. Johari and Buchanan1 have written a Fortran program for generating standard projections and along similar lines we have produced a short but completely general program for generating any section through reciprocal space. The required inputs are the lattice parameters and angles for the real crystal. The Miller indices of the direction [U, V, W] parallel to the electron beam are then specified and the program will generate the Miller indices of the plane normals perpendicular to [U, V,, W] up to some specified integer. A subroutine can be inserted to test for forbidden reflections if desired. We have used such routines for fct and hcp crystals. As each permitted index is generated it is printed or punched out and no storage arrays are utilized in the computer. The normal diffraction pattern corresponds to the zero-order Laue zone, but with thin crystals or crystals of large lattice parameters the higher-order Laue zones may contribute to the diffraction pattern. Accordingly the program will generate successive Laue zones and project them onto the zero-order zone. The output of the program first lists the zone axis [C, V, W] and the Laue zone, and then gives a list of permitted reflections and the corresponding XP and YP coordinates of the reciprocal lattice point in angstroms-&apos;. In addition, ZP, the perpendicular distance of the reciprocal lattice point from the (U, V, Ur) plane in reciprocal space is given, as is the reciprocal interplanar spacing. In the case of the zero-order Laue zone ZP is zero. A diffraction spot from the higher-order Laue zones will be very slightly displaced from the computed coordinates as its position in an actual pattern is given by projection along the diffracted beam2 and not along [u, V, w]. For any given electron wavelength this correction could be readily incorporated into the program, but as it only amounts to -1 pct it was decided to leave the program in its most general form, i.e ., a computation of points

Jan 1, 1970

By W. A. West

ONE who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult&apos;s law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener&apos;s paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion of the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1946

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,&apos; using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French&apos;s studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, -1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2 CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws .in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were. tested for air circulation and air tightness and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering .these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By F. Cadena

HIWASSEE Dam, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about 1/4 in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. FLOWSHEET Rock is loaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4 ¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1939