Search Documents

By Robert F. Mehl

THE solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstätten figures profusely nor with great ease. A study of the Widmanstätten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstätten figures.1 ALLOYS OF ALUMINUM WITH COPPER The most accurate determination f the solid solubility, of copper in aluminum seems to be that by Dix and Richardson,2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548°, and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solution on cooling tends to precipitate the compound CuAl2, and this conclusion has been confirmed experimentally by Schmid and Wassermann .3

Jan 1, 1932

By Douglas R. Piteau, Dennis C. Martin

Instability of rock slopes may occur by failure along pre- existing structural discontinuities, by failure through intact material or by failure along a surface formed partly along discontinuities and partly through intact material. Although certain fundamental failure modes are recognized, the mechanisms of slope failure are varied and complex. Such mechanisms are governed by the engineering geology conditions of the rock mass, which are almost always unique to a particular site. An understanding of failure mechanisms requires a knowledge of the physical, mechanical and strength properties of the intact material and discontinuities which make up the rock mass, as well as the structural geology and hydrogeology. These engineering geology parameters also must be evaluated with respect to the slope geometry to determine failures which are kinematically possible. Only after obtaining a reasonable appreciation of the possible failure modes can a rational mechanical stability analysis be carried out. Both two-dimensional and three-dimensional failure mechanisms should be considered in assessing the design of rock slopes. Simple analyses methods are used initially to identify those possible failures which could control slope stability. More complex and detailed analyses usually are required for a few critical failure modes which could control stability, or where a more complex type of failure mechanism is envisaged. Complex failure mechanisms are usually identified when assessing previous slope failures. More detailed information concerning slope geometry and engineering geology parameters must be acquired where analyses must be more rigorous.

Jan 1, 1983

By E. V. Crane

A TREMENDOUS volume of the metal rolled annually into sheets, strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features in common with rolling and wire-drawing methods. Combinations of stresses are different, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group.

Jan 1, 1931

By T. G. Fulmor, William Wraith

What impelled The Anaconda Company to dismantle and move a concentrator 25 miles that was already operating at a rate of 35,000 ton per day? The answer to that question takes in almost exactly 49 years and perhaps 10 complete cycles of the metallurgical wheel in the Anaconda, Mont., mill. One could say with truth that the move is a logical next-step in the development of metallurgy in The Anaconda Co. In the old concentrator at Anaconda, the background story is unfolded: - Gravity separation by jigs, later supplemented with gravity tables, 1905. - Separate sand and slime froth flotation, 1915. - Acid bulk froth flotation, 1917. - Bulk alkaline flotation, 1926. - Alkaline flotation of total ore without sand- slime separation due to change in ore type. 1939.

Jan 5, 1964

By AIME AIME

HONORARY COMMITTEE. HON. C. D. WALCOTT (Chairman.), Director U. S. Geological Surrey. HON. FREDERICK I. ALLEN, Commissioner of Patents. DR. FRANK BAKER, Superintendent National Zoological Park. MR. CHARLES A. BELL, President American Security and Trust Co. MAJOR JOHN BIDDLE, Engineer Commissioner of District of Columbia. ADMIRAL C. M. CHESTER, Superintendent U.S. Naval Observatory. GENERAL WILLIAM CROZIER, Chief of Ordnance, U. S. A. ADMIRAL GEORGE DEWEY, Admiral of the Navy. COLONEL CLARENCE R. EDWARDS, Chief Bureau. of Insular Affairs. MR. WILLIAM C. FOX, Director Bureau of American Republics. MR. CHARLES C. GLOVER, President The Riggs National Bank. GENERAL A. W. GREELY, Chief Signal Officer, U. S. A. MR. BERNARD R. GREEN, Superintendent Library Building. GEN. G. H. HARRIES, Vice-President Washington Electric Railway Co. HON. E. A. HITCHCOCK, Secretary of the Interior. COMMANDER H. M. HODGES, Chief Hydrographer, U. S. N. PROF. W. H. HOLMES, Chief Bureau of American. Ethnology. PROF. S. P. LANGLEY, Secretary Smithsonian Institution. GENERAL ALEXANDER MACKENZIE, Chief of Engineers, U. S. A. ADMIRAL N. E. MASON, Chief Bureau of Ordnance, U. S. HON. WM. M. MEREDITH, Director Bureau of Engraving and Printing. HON. V. H. METCALF, Secretary Department of Commerce and Labor. HON. WILLIS L. MOORE, Chief -U. S. Weather Bureau. HON. PAUL MORTON, Secretary of the Navy. MR. F. H. NEWELL, Chief Reclamation Service, U. S. Geological Survey. HON. S. N. D. NORTH, Director Census Office. CAPT. E. C. PENDLETON, Superintendent Naval Gun Factory. MR. GIFFORD PINCHOT, Chief Forester, Department of Agriculture. MR. HERBERT PUTNAM, Librarian of Congress. ADMIRAL CHAS. W. RAE, Chief Bureau of Steam Engineering, U. S. A: MR. RICHARD RATHBUN, Assistant Secretary Smithsonian. Institution. HON. W. T. RICHARDS, Commissioner General Land Office.

Jul 1, 1905

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By J. F. Keefe, C. J. Bier, O&apos

This study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metal-lographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. Material Used The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: Per Cent Per Cent BY BY Particle Size "Weight Particle Size "Weight Mesh Microns /80.... 0.00 43/32.... 17.49 80/I00..... 32/20......16.68 100/140.... 0.34 20/10.... 23.14 140/200___ 15.25 10/5..... 4.64 200/230....... 5.00 5/0...... 0.75 230/325.... 16.70 — 325....62. 69 The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1945

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By R. Van A. Mills

ONE of the most important problems facing the petroleum industry is the profitable recovery of oil that is left underground by the ordinary methods of production. It is true that vast quantities of oil are being recovered from fields previously considered depleted by the pressure restoration method, the most widely applicable -and most successful means of obtaining greater recoveries that has thus far been, developed. But notwithstanding the progress that is being made in the field applica¬tion of this method there is urgent need for a better understanding of the fundamental principles that are involved. To meet this need the Petro¬leum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., during the past two years has conducted a series of intensive laboratory and field investigations. The larger part of the work has been carried on in the laboratory to supply the much needed information upon fundamental principles, information which few if any of the oil companies are in a position to supply for themselves. In all of this work the Bureau is endeavoring to correlate the results of laboratory investigations with those in the field, using the results of one to guide or check the other. This paper is primarily a progress report, briefly outlining the Bureau's methods of study, the laboratory and equipment in use, the preliminary problems that had to be solved in order to attack the major problems at hand, the methods of attacking some of the major problems, and some of the results of the investigations to date.

Jan 1, 1928

By Y. S. Bonillas

Page I. Introduction.......................... 286 II. Physiography.......................... 286 : 111. Introductory Geology...................... 287 IV. Rocks of the District ...................... 288 (A) Sedimentary Rocks..................... 288 Pinal Schist ........................ 288 Bolsa Quarteite....................... 289 Abrigo Limestone...................... 290 Capping Quartzite..................... 291 Martin Limestone...................... 292 Escabrosa Limestone .................... 295 Naco Limestone....................... 296 Cretaceous Deposits..................... 296 Glance Conglomerate................... 296 Morita. Mural and Cintura Formations........... 297 (B) Igneous Rocks........................297. Pre-Cambrian Granite.................. 297 Pre-Cretaceous Granite Porphyry............. 298 Rhyolite........................301 Other Dikc Rocks.................... 301 V. Structural Geology........................ 304 General Structure of Mule Mountains............. 304 Fault Blocks and Other Divisions............. 304 Igneous Rocks...................... 312 Copper Queen Block..................... 313 Fault Blocks...................... 313 Intrusions....................... 315 Don Luis Block....................... 315 Intrusions and Orebodies................. 316 VI. Geologic History......................... 316 VII. Metamorphism and Mineralization................. 318 General Metamorphism.................... 318

Jan 1, 1917

By W. L. III McMorris, R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, C. E. Capes, A. W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER, and W. L. MCMORRIS III INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken the loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Nether- lands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War I1 in the lab- oratory of the Dutch State Mines under the direction of M. G. Driessen. A 15 tph (13.6 mt) pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of fie1 in London. In April 1945 operation of this pilot plant was observed by H. F. Yancey, who was so

Jan 1, 1979

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920

A filled stope is one in which the support for walls and men and, at times, for the back of ore, is furnished by waste rock or sand tailings. The filling may be rock sorted out in the stope or from the walls, develop-ent, or the surface. The orebody is mined in sections, each practically an open or timbered stope, filled wholly or in part before adjacent ground is attacked. As a rule, the filled-stope method is limited to overhand flat-back, stepped-face, or rill stopes. The examples given are Copper Range, Iron Cap, Verde district, Zaruma district, Lucky Tiger, and Silver King Coalition.

Jan 1, 1925

By Henry M. Howe

Jan 1, 1908

By R.J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By David J. Mack

THE structures and properties of the copper-aluminum alloys have been the subject of much study since the classic investigation of Carpenter and Edwards1 focused attention on the engineering utility of these alloys. It was recognized at an early date that the metallographic structures developed in the aluminum bronzes were similar to those developed in steels, both in the annealed and the rapidly cooled state. Most investigators have been concerned with the acicular, martensitic-like structure formed from the ß solid solution upon rapid quenching; the transformation of the ß under equilibrium cooling to a lamellar eutectoid having been relatively neglected. With the introduction in 1930 by Davenport and Bain2 of the isothermal transformation technique for studying eutectoidal decompositions, a new field was opened. Although an enormous amount of work has since been done on the isothermal transformation of steel, study of structurally analogous systems has been almost totally overlooked. The outstanding exception was the prize-winning paper† of Smith and Lindlief3 who investigated the decomposition of the ß phase in copper-aluminum alloys by isothermal methods. This was followed in 1934 by Wasserman's reviews of available information on analogous transformations in eutectoid alloys. Since that time no comprehensive study of isothermally transformed eutectoids analogous to steel has appeared, although many valuable contributions have been made to an understanding of the structures developed in such systems. Important papers have been published by Kurdjumow, Gridnew and co-workers, 5-17 Obinata,18,19 Greninger,20,21 and others .22.28 The work to be described in this paper was an out-growth of preliminary studies on the isothermal transformation of a eutectoid aluminum bronze, after it became apparent that the alloy under study was reacting somewhat differently than the similar alloy used by Smith and Lindlief. PRELIMINARY EXPERIMENTS The material used in this study was a high purity aluminum bronze especially prepared by Ampco Metal, Inc. It analyzed: Copper-88.o7 pct, Aluminum-11.89 Oct, Iron-0.02 pct, Manganese-0.01 pct, Others-Balance. Although some disagreement exists on the exact composition of the eutectoid, this alloy was believed to be of essentially eutectoid composition even though some pro-eutectoid* delta particles existed in the microstructure of furnace cooled specimens. Specimens transformed isothermally at temperatures slightly below the eutectoid showed relatively large amounts of pre-eutectoid delta, but as will be shown later, this results

Jan 1, 1947

By R. J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By A. M. Gaudin

THIS paper presents, with the help of colored photomicrographs, the new method of mineral identification termed "selective iridescent filming." This method pertains to the field of determinative mineralogy, which it provides with tools for: (1) phase identification, (2) solid solution analysis. The method should be particularly useful in the applied fields of: (1) paragenesis of ore deposits, (2) mineral dressing, (3) mineral synthesis and study of phase equilibria.

Jan 1, 1938

W. 0. HOTCHKISS,* Madison, Wis.-When we began to do geological field work in the Lake Superior region, we found a correlation in existence, and, as youngsters, accepted all that as settled. Both Mr. Allen and I, since that time, have seen a great many things that were not apparent nor visible to Van Hise, and those who worked with him; we realize now that the correlation was not final and that much remains to be determined concerning geology of the Lake Superior region. My attitude on this matter is that we should not publish an amended correlation as a final thing. We should avoid, in every way possible, foreclosing the minds of those who follow us in working in the geology of this region. As a matter of fact, no correlation can be final at present, because facts and data are accumulating so rapidly that every classification must be immediately modified to fit further observation. Consequently, my attitude in this matter would be, instead of saying that the iron formations of the Lake Superior region are all Middle Huronian, to say that there may be three Huronians-or four or five- we do not know. I believe it is better policy to hold to our present correlation. I do not believe there is any economic benefit to the mining man or the geologist working on problems relating to explorations for iron ore, that cannot be just as well solved by maintaining our present correlation, with a. wholesome idea of our lack of knowledge and the necessity for further detailed work. Then, if any new horizons are discovered in any particular range, the minds of the investigators will not be foreclosed because some one has said that all the iron formation is in the Middle so that there is no use looking elsewhere for it. There is use looking elsewhere, in many cases, as the ore deposits become exhausted.

Jan 1, 1920