Search Documents

By Henry M. Howe

In discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness,strength, and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not; qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them, a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces-

By J. E. Tiffany

FOR blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flame make their use safer than that of non-permissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless. The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.1 This paper contains a description of the methods worked out subsequently in another mine in that district.

Jan 1, 1928

By Herbert D. Drechsler

Mining Finance-is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm". The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance.

Jan 1, 1978

By Karl Sundberg, Allen Nordstrom

Interesting results were recently obtained in geophysical prospecting at the Questa mine of the Molybdenum Corpn. of America in New Mexico. This paper describes that survey, which was carried out during October and November, 1927, by the Swedish American Prospecting Corpn. It is hoped that the paper will make it possible for the mining man to form an opinion of the applicability of geophysical prospecting under difficult conditions, showing, as it does, the results when prospecting for small small orebodies with comparatively poor conductivity, in a region of rough topography. Some principles underlying electromagnetic prospecting not known to be published previously will also be given in an elementary way, with special attention to the general structure of the electromagnetic field. Geological. Conditions at Questa The property is situated in the Taos range of the Rocky Mountains in northern New Mexico. About this region, L. C. Graton says:' The main range is made up of Pre-Cambrian granites, gneisses and schists but in the vicinity of Red River igneous rocks of later age are present almost to the exclusion of the older series. These younger rocks are divisible into two groups. The older of the two, probably Pre-Tertiary age, is represented by large intrusive masses of monzonite porphyry, usually containing considerable quartz. The more recent group comprises intrusive and probably effusive dark-colored andesites and coarse andesitic breccias, some of which contain fragments of the monzonite; there are also flows of rhyolite and beds of rhyolite breccia. The evidence regarding the relative age of the andesite and the rhyolite is not wholly satisfactory, but there is little doubt that the andesite is the older. The ore deposits, although occurring more commonly in the monzonite porphyry than in the rhyolite, nevertheless are believed to be genetically related to the rhyolite. They certainly cut the rhyolite or andesite in places, and hence fall in the late Tertiary. The molybdenite at the Questa mine occurs in veins in the alaskite granite porphyry belonging to the older part of the Pre-Tertiary eruptives. Overlying the granite porphyry is the granodiorite, capping the granite

Jan 1, 1929

By Oliver C. Ralston

THE two chemical compounds, natural sodium carbonate and sodium sulphate, in their anhydrous condition are dealt in as "soda ash and "salt cake”-names from an earlier day that are not as precise as the present accepted terminology. Once a large part of the sodium carbonate recovered was in the ash of seaweed, so it was logically called soda ash, and the corresponding potassium carbonate, once mainly recovered from wood ashes, was called potash. The term "salt cake" was applied to the sodium sulphate resulting from interaction of sodium chloride with sulphuric acid or sodium bisulphate, to form hydrogen chloride gas and an anhydrous cake of sodium sulphate. It was called "salt cake" and also "glassmaker's salt cake" because much of it was used in the production of glass. The two salts occur in nature in a variety of forms, but whereas an- hydrous sodium sulphate (thenardite) is fairly common, the anhydrous normal sodium carbonate, Na2CO3, is almost never found in nature. The monohydrate (thermonatrite), Na2CO3.2H2O, is seen occasionally, but it is never a major constituent in natural "soda" deposits. The high solubility of normal sodium carbonate is one reason for this. While both compounds occur widely in brines, the solid salts found in nature are usually trona (Na2CO3.NaHC03.2H2O) and thenardite (Na2SO4). The natural brines containing workable quantities of the two sodium salts are largely found in the arid and semiarid portions of the western United States and other countries. The classical discussion of the resources of these brines are those of Clarke,5 Chatard.4 Packard,19 Gale,11 and Wells.28 From North Dakota to California and from Arizona to the Canadian provinces of Alberta and Manitoba, saline lakes, dried-up lakes, playas, and similar land-locked depressions contain accumulations of saline matter. Sodium chloride is the predominant salt but some of the lakes contain predominantly either sodium carbonate or sodium sulphate. Often sodium carbonate

Jan 1, 1949

By Jack Parker

There are some simple theoretical approaches to pillar design but they leave much to be desired. There are also more complex theoretical approaches, but at this time the most realistic approach is to go into the mines and observe and measure how real pillars are performing under real conditions; to allow the information thus gathered to ferment in our minds - then to project the behaviour of those pillars into our new designs and mining techniques, probably with no formulas at all. Examples, from half-a-dozen different mines, show how a simple- minded approach, through observation and measurement, led to changes in pillar design which often contradicted the textbook but made very significant contributions to mining safety, efficiency and costs. The good news is that we know a lot more about pillar design than we realize. We have, between us, looked at millions of pillars of all kinds, under all conditions, but we have overlooked what they are trying to tell us. We can take problem situations and turn them into opportunities and, in that way, become better stewards of the resources which have been given to us.

Jan 1, 1983

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

By P. H. Dudley

THE piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive pourer and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of froth 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an over-flow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are Dot oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it :is in this way that the blow-holes are closed it the low-carbon steels.

Jan 4, 1913

By H. S. Coe, G. H. Clevenger

Engineers have long recognized the desirability of correlating the data obtained from small-scale slime-scttling tests with commercial work as carried on in large tanks. This need, though most apparent in designing new installations, frequently arises also in existent plants, since a large range of experimental work can be performed without interfering with regular operation. General Settling Phenomena In order to develop rational methods of laboratory testing, it becomes necessary to study the general phenomena of settling. Since it was desired to give the public the benefit of these methods at as early a date as possible, together with the knowledge of the general principles of slime settling necessary for a clear understanding of the laboratory tests, we have ventured to discuss the subject in so far as brought out by the work which we now have under way. We realize that certain of our preliminary conclusions may be subject to modification, but it seems probable that, with but few exceptions, the general laws enunciated will cover the settling behavior of all pulps encountered in metallurgical plants. However, it must be recognized that there is still a vast amount of work to be done upon certain phases of the subject; therefore, at this time we will attempt only a discussion of the behavior of ore pulps during the process of settling or dewatering, under certain given conditions. The laws and principles controlling these conditions are not fully established, so that a complete discussion of them will not be attempted in this paper. In metallurgical practice, slime pulp consists of water, finely divided sand

Jan 1, 1917

By Henry M. Howe

IN discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness, strength„ and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general,, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel ; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to, meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not;. qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them., a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces- * This paper was read in opening the discussion on the motion to adopt the report of the International Committee on the Nomenclature of Iron and Steel. At the conclusion of the discussion the resolutions on page 44 were adopted.

Jan 1, 1877

By Graham Bright

THE rapid increase in reliability, the low cost f operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the' motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made.

Jan 9, 1921

By C. P. Fiske

THE pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers; and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance? come the condensers, as large numbers are used in the manufacture of spelter, and improvements m quality result in material decreases in working cost. , While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they-are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are concerned. Materials Bond Clay.-The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather -it in the, accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss. of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later), accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is, evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons-with the clay as usually handled.

Jan 10, 1917

By Frederic Benard

THE treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining Co, is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of palladium and platinum, wet methods are used to remove the greater proportion of these metals before electrolytic refining in the Wohlwill cells. THE PLANT The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side of the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. . Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accomplished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equipped with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suction filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill. On the bottom level are two rectangular cementation tanks, 24 by 48 by 24 in. deep, and a suction filter used for removing the platinum-metal concentrates. The circulating pump for the packed tower is also here. Suction is provided by a vacuum pump having a capacity of 8 cu. ft. at 20-in. vacuum.

Jan 1, 1938

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By C. F. Nagel

This paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. Heat Treating Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this irnprovement may be illustrated by some typical properties of dura-lurnin (Table 1). It is essential that the material be in the wrought condition in order to obtain rnaximum heat-treatment effects. In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By W. G. Matteson

THE origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete information revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill' advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,2 using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no. evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of, the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the, subsequent

Jan 2, 1921

By H. E. Mussey

WHEN the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then FIG. 1.-BLAST-FURNACE DEVELOPMENT IN ALABAMA. completed were referred to as monumental.1 Their dimensions are given in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 10, 1924

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By C. A. O’Connell

Surface exploration drilling at Mufulira started in 1928, with drillhole No. 1 intersecting ore near the eastern fringe of the deposit. Subsequent drilling along strike intersected ore until the western fringe was fixed some 7500 ft west of drillhole No. 1. Further intensive drilling down dip disclosed a large triangle of ore with its apex 3350 ft deep. It contained approximately 11 6 million tons of ore at 4.41% total copper in three superimposed orebodies. The east and west limits of the orebodies were presumed to have a pronounced rake to the north with a strike length of 8000 ft. Subsequent exploration underground seemed to bear out this presumption to the 1150 ft level. In 1947, attention was directed to the area west of the known orebodies in conjunction with plans for increased production and increased depth of the mine workings.

Jan 12, 1962