Search Documents

By John Chipman, K. C. McCutcheon

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or dounward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,' in 1925, analyzed the gases extracted from rimming, sernikilled and killed steel ingots and found that the chief constituent of the rimmining gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune² reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By S. J. Kidder

The Mogollon mining district is in the southwestern part of New Mexico near the southern end of the Mogollon range, from which the district takes its name. The town of Mogollon is but 371/2 miles in an air line northeast of Clifton, Ariz. The air-line distance from Silver City is 521/2 miles and from Tyrone, 57 miles. Supplies are transported by motor truck from Silver City. The distance by road is 75 miles, half of which is an improved highway of modern construction. Transportation has always been a large item of expense in carrying on operations in the district. Valuable ore is said to have been discovered in the Mogollon Mountains as early as 1870 but the first regular prospecting was carried on in 1875, by James C. Cooney, a sergeant from Fort Bayard. His discovery of rich silver-copper ores in the region of Mineral Creek led to the establishment of the Camp of Cooney. Remote from any settlements where there was a semblance of law and order, and harassed by the Apaches, development was slow and nearly 10 years elapsed before the village of Mogollon was established on Silver Creek. Prospecting in this section of the district had disclosed the outcrops of several promising veins containing silver-gold ores. Among the early claims located were the Last Chance, Top and Confidence, on what has proved to be the most productive vcin in the district. To the end of 1922, the Last Chance and Top claims had produced approximately 600,000 tons of ore and nearly 200,000 tons had come from the Confidence group of claims. The total value of the ore produced from this vein alone has amounted to about $9,600,000 in silver and gold. The Fanney vein was developed later and during its most active period of production contributed more than half of the output of the district. Other important locations, though far less productive than the above, were the Maude S, Deep Down, the Deadwood and the Pacific.

Jan 1, 1925

By R. J. Wysor

MoRe than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same, furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100" F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently done some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C.,R. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based on the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations. Method of Conducting the Tests The location of the pyrometer fire ends is shown in Fig. I, a plan of Bethlehem Steel Co.'s "G" blast furnace, hot-blast stoves, and main. Bare fire ends were used at both positions "A" and "B," being inserted

Jan 1, 1916

By James Herbert Bartlett

I desire, very briefly, to call the attention of the Institute to the iron trade of the Dominion of Canada. A wonderful development is now going on in Canada. The completion of the Canadian Pacific Railway, and the numerous extensions of the various railways all over the country, combined with the progress made in nearly every kind of manufacture, is drawing attention to the field offered in Canada for the profitable employment of capital, and specially to the opportunity there is for the manufacture of iron. In a paper presented to the Institute at the Halifax meeting,* the writer gave a review of the varions attempts to manufacture iron in Canada. The facts then presented were not such as to offer much encouragement to any one to embark in similar enterprises under the conditions then existing, but, happily, these conditions are now changed, and an early development may be anticipated. There are two reasons which make the present time an appropriate one to direct attention to the field offered for enterprise in this direction, the first being the very favorable reports of the experts who examined and reported on the exhibit of minerals at the Colonial and Indian exhibition, held in London, England, last year. The exhibits there of coal and iron attracted so much attention that at the request of the Iron and Steel Institute a paper on the " Ironmaking resources of our Colonies as illustrated by the Colonial and Indian Exhibition," was prepared and read at the last meeting of the Institute.? This report of 135 pages is very exhaustive, and the conclusion arrived at, so far as Canada is concerned, is, that she has in many parts of the country every natural facility for the manufacture of iron. The second and more important reason is the recent change in the Canadian customs tariff inaugurated in May last. The tariff is now generally two-thirds of the American tariff, in addition to which the Government, in order to encourage the manufacture of iron, grants a bounty upon pig-iron made in Canada out of Canadian ore.

Jan 1, 1888

By John A. Putnam, Morrough P. O’Brien

DATA on the physical and thermodynamic properties of hydrocarbons have been made available in recent years but the formal method of applying these data to flow in porous media appears not to have been fully developed. By making usual thermodynamic assumptions and employing existing data on permeability to two-phase flow, Darcy's law may be applied to obtain the flow characteristics for representative combinations of flowing medium and geometry. The numerical examples presented herein are based on hydrocarbons for which complete physical and thermodynamic data are available under equilibrium conditions. INTRODUCTION Thermodynamic data are obtained in the laboratory under equilibrium conditions and their application requires the assumption that equilibrium also exists during flow. This assumption is at least usual in engineering analyses, though not easily justified in many instances, and will be followed here. In regard to hydrocarbons, laboratory experience in determining the pressure-volume-temperature relationships indicates that gas-liquid mixtures must often be stirred vigorously for periods of 15 to 20 min. before reaching equilibrium. On the other hand, boiling and condensation are known to occur on solid surfaces and the large surface exposed to the flowing substance by a porous medium may bring about rapid approach to equilibrium. For the purpose of providing at least a guide to experimentation and a standard for later comparison with experimental results, it will be assumed that the phases present in cross sections perpendicular to the direction of flow are in thermodynamic equilibrium. Another assumption usually made in the solution of problems of flow in porous media is that the fluid remains at a constant temperature; i.e., isothermal flow. This assumption is arrived at by considering the porous medium and surroundings to be an infinite heat source and the rate of heat flow to be infinite at a boiling front. Its validity depends in large measure upon the character of flow, the number of components, and the physical and thermodynamic properties of the fluid. However, the assumption of isothermal flow represents a limiting case. The other limit can be represented by the assumption that the fluid is thermally isolated; i.e., irreversible adiabatic. The thermodynamic process characterizing the actual flow of a given fluid system probably lies somewhere between these two limiting cases and might be thought of as a flow system in which the confining walls are maintained at a constant temperature. For isothermal flow the solid material of the porous media is considered as the infinite heat source capable, without loss in temperature, of giving up heat to the fluid as the latter tends to cool by expansion. For the thermally isolated system, the solid material is considered to give up no heat to the fluid. In the intermediate case the impervious walls confining the porous media are at constant temperature from which heat is transferred along various paths, solid and fluid, throughout the porous media. It would appear that an actual petroleum-

Jan 1, 1941

By A. S. Dwight

Taking up first the lead field, flotation concentrates offer serious difficulties in handling and in preparing for the blast furnace, quite aside from the problems presented to the furnaceman by the necessity of smelting smaller tonnages of material higher in grade and usually basic in character, with the consequent changes in flux requirements and furnace operation. As received at the smelter, these concentrates are always wet and usually of the consistency of sticky mud. Difficult enough to handle in warm weather, they are worse in winter, when it may be necessary to blast them out of the cars. They hang up in bins and chutes and stick to conveyors, requiring the constant attention of the operators. If dried they become like wheat flour, involving heavy dust losses in handling and in furnace operations. Roasting in hearth furnaces is more difficult than with coarser materials. Dust losses are increased and, what is more serious, the moist concentrates tend to form balls or nodules, which harden and pass almost unaltered through the furnace with consequent high sulfur in the product, while the unballed fine particles lie on the hearth in a dense bed, practically impenetrable to the oxidizing gases, so that roasting takes place only on the surface of the bed. A more prolonged roasting period is therefore required and the capacity of a given furnace is decreased. They are entirely too fine to be charged into the blast furnace, even if thoroughly roasted; excessive flue-dust losses, irregular operation and slowing up of the furnace would be the obvious result. Consequently, it was early recognized that flotation concentrates would have to be put in coarser condition for smelting and the universal method adopted has been the Dwight & Lloyd process of sintering. This did not usually

Jan 1, 1928

By Thomas L. Garwood, F. C. Menk

I T is generally accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uni¬form bed. With a dusty feed the fines tend to segregate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants deducting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets.

Jan 1, 1943

By W. F. Holbrook, T. L. Joseph

The problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron and hot metal of lower sulfur content. As most of the sulfur in the iron originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blastfurnace slag has been thought to be related to desulfurization and has been investigated by Feild and Roysterl, also McCaffery and his associates*, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice. Development of Testing Method Because slag and metallic iron are immiscible, the desulfurization reaction is heterogeneous, occurring only at the interfaces between slag and metal bodies. In the blast furnace the newly reduced iron, containing FeS, descends through the slag bath probably either as small drops or streams, at the interfaces of which desulfurization occurs. After its descent through the slag the iron collects to form a bath of metal, at the top surface of which desulfurization reaction probably occurs. These two steps have been thought to account for all desulfurization in the blast furnace. Kinney3 found that metal removed from the blast furnace just above the tuyeres contained three to four times as much sulfur as the iron at cast. Herty and Gaines4 conclude that most of the sulfur is removed while the metal is passing through the slag. Mund, Stoecker

Jan 1, 1936

By H.A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By Kenneth B. Barnes, George H. Fancher

With the advent of water-flooding into active commercial usage in half a dozen areas in the Mid-Continent, the process passes the experimental stage and joins other methods and processes now in use which have been found suitable in one oil field or another in securing a more profitable production than has existed heretofore. The use of the air-gas lift, acidization, pressure maintenance and repressuring have presented their problems in economics and engineering during their introduction and extended application. When a new field is discovered or attention is turned to an old producing area in which these methods have not been considered, it is to be expected that these problems again arise. While some information is available as to the results obtained by water-flooding in a few localities in the Mid-Continent, the extrapolation of the sand data on which the results are based, for even generalized use in other areas and fields in the region, is hazardous. It is precarious to assume that the same physical condition will obtain in a sand over more than small, special areas. This paper is concerned with a brief presentation of such data as are available to the authors on existing operations, a survey of the region and extent to which application of the method seems most likely to be made, an estimation of the crude reserve existing for such operations, suggestions as to the importance of core analysis in guarding against uncontrolled floods and its usefulness in predicting ultimate recoveries, and comment on some of the economic phases involved. These subjects, as concerned with water-flooding in the East (notably Bradford, Pennsylvania), have been discussed in detail in the literature and are generally well known. Especially is this true of discussions of the mechanical equipment and various lease layouts and development patterns for water-flooding.

Jan 1, 1936

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By W.C Ellis, Earle E. Schumacher

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansen1 and Haughton,2 the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 257.3°C ± 0.1°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys,4,5 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157.2°C ± 0.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4'C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. THERMAL ANALYSIS Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high flash point was used. A platinum-platinum rhodium thermocouple 0f fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermo-couple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.2°C, and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it seems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16r, in. thick, sufficed to give a cooling rate of from 1° to 2°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By M. Muskat, H. G. Botset, R. D. Wycoff, M. W. Meres

The subject of the flow of homogeneous fluids—gases alone or gas-free liquids—through porous media may be considered at the present time to be fairly well completed. That is, analytical, graphical, numerical, or experimental methods are now available for obtaining detailed descriptions of the behavior of such homogeneous fluid systems of any reasonable geometry. Thus, satisfactory empirical techniques are now well established for the determination of the permeability of porous media for homogeneous fluids, the numerical magnitude of this permeability uniquely and completely describing a porous medium as a carrier of a homogeneous fluid. Considering this constant as known, the treatment of a wide variety of specific problems involving either the flow of gases or liquids has been carried through to satisfactory conclusions. Beginning with the simple case of strictly radial two-dimensional flow of a liquid or gas into a well under steady-state conditions, generalizations have been developed to apply for systems where the flow is not strictly radial, due either to a lack of uniformity in the reservoir pressures at points distant from the well or deviations from circularity of the external boundary whereby the fluid is being supplied, and finally, to the lack of complete penetration of the well into the producing strata. Satisfactory descriptions are now available for cases where gravity is acting as the driving agent inducing the flow of liquid into the well, either alone or as a supplement to the effect of pressure. The effect of acid treatment on limestone wells has been given a reasonable interpretation on the basis of the fundamental theory of the flow of homogeneous fluids through sands, as have the important features of the problem of water-coning. Then, too, systems in which the outlet of the fluid from the underground reservoir is of a predominantly multiple character may be now considered as in the domain of

Jan 1, 1937

By John Chipman, Theodore B. Winkler

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938