Search Documents

By E. D. McMurry

INTRODUCTION Before discussing the use of the free piston; it may be well to explain briefly the type of gas lift valves with which the loo] is designed to function. The gas lift valve ii nothing more or less than a small back pressure regulator. It; construction consists of an outer hous ing covering a seamless metallic bellows in such a way as in form a sealed pressure vessel or pressure dome. To the bellow* in attached a stem and to this stem is attached a .rating member. When the valve is run into the hole, a pre-delermined pressure charge is placed in the pressure dome. As shown in Fig. 1. the valve is furnished in four different major assem-blies. to accomplish good results in different types of wells. The valve is mounted on a pup joint (Fig. 2a) : the eoin-plele assembly is entered into the tubing siring at the desired location. Each valve is furnished with a revere flow check valve (Fig. 2-b) to eliminate any back wash through the mechanism. Valve action is as follows: At any time the casing pressure is allowed to exceed the pressure forces within the pressure dome of the valve, the valve simply opens and passes gas from the rasing annulus into the tubing. When the casing pressure forces arc allowed to bleed to a force less than the pressure force within the dome, of the valve. the valve closes. With this type of construction. it is possible to open and close the valve or valves at will from the surface, the medium of the gas pressure in the rasing annnlus. The cycle of operation is governed by a tine cycle motor valve, commonly referred to as a gas lift interutitter or gas life surfacr controller (Fig. 3). In actual practice. after the well is unloaded only one valve is in operation . . . all other valve.: remain in the closed position. On pre-determined time cycles, it is possible to open and close this operating valve at will, and to pass the desired amount of gas through this valve wheneler needed. This method of gas lift is widelv used and has been found In be very efficient. However, it has long been known that even greater efficiency would be obtained if it were possible to place Piston between the injected gas and the fluid head. The free piston which will be discussed here was designed to accomplish this end and has been found to do so with very satisfactory results. DESIGN AND OPERATION OF THE FREE PISTON Basically. the free piston consist- of a telescoping assembly in which are incorporated the various control and operating parts (Fig. A set of sleeve valves which are opened and closed by movement of the telescoping section is contained in the. tool. A cross section of the free piston is shown in Fig. 4-11, 'rile main body cotain- a seamless monel bellows of the same type as that generally used in pressure charged gas lift valves (Fig. 4-c), and a valve core to permit placing a pressure charge in the bellows before the free piston is placed in service. The bellows is the main control unit of the free piston and performs two function: 1. It governs the opening and closing of the sleeve valves. a.: dictated by the producing activities of the well in which the piston is operating. 2. In its normal position, it holds a rubber packer in an elongated position to permit passage of fluid between the packer and the tubing walls. The lower section of the free piston contains a hydraulic shock absorber which cushions the return of the tool to its

Jan 1, 1953

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

By W. S. Morris, R. R. Bradenthaler, G. Wade

Petroleum engineers generally are of the opinion that the flow conditions and, therefore, the formulas that apply to the flow of oil and gas in long pipe lines differ in many ways from flow conditions in oil wells. One of the reasons why the formulas in common use for pipe-line flow do not correctly apply to oil wells is that the flow lines are vertical and not horizontal. Another factor to be considered is that the fluid is a mixture of oil and gas and that the physical characteristics of these two components are affected differently by changing conditions of pressure and temperature during upward flour. Realizing the need for accurate data on flow in vertical pipes under conditions caused both by natural flow and the gas-lift, the U. S: Bureau of Mines has installed equipment at the Petroleum Experiment Station, Bartlesville, Okla., for the purpose of studying this problem. In additon a study will be made of the comparative effects of different natural-flow and gas-lift methods of producing oil on ultimate production from reservoir sands. Experimental Equipment The experimental equipment consists of a regular oil-field steel derrick, a large pressure tank installed in a concrete pit beneath the derrick floor, compressors and pumps, gas separators and absorbers, metering and control devices, and the necessary pipe connections. The crown-block level represents the derrick floor at an oil well, and the "producing sand" is the pressure tank below the derrick floor. The difference in elevation between the crown-block level and the tank is 90 ft. Figs. 1, 2 and 3 show the construction and exterior arrangement of the equipment. The success of the experiment will of course depend largely upon the accuracy of the oil and gas measurements and the temperature and pressure determinations. Because extreme accuracy is necessary, all oil and gas measurements will be checked at least twice, and in some

Jan 1, 1929

By T. M. Geffen, J. L. Sanderlin, F. F. Craig, D. W. Moore

Scaled reservoir models have been used to study the effect of gravity on oil recovery performance in frontal-drive operations; namely, water, gas, or solvent flooding. The difference in density between the reservoir oil and the injected fluid causes their segregation, resulting in a non-uniform advance of the fluid front. In the laboratory flow tests, which simulated both five-spot and linear injection operations in flat reservoirs, the viscous, capillary, and gravity forces present in these operations were scaled. Dyed fluids were used so that the gross movement of the injected fluid could be observed. The studies covered a range of injection rates, formation thicknesses, and rock and fluid properties normally encountered in field operations. The results of the model tests indicate that the volume of the reservoir contacted by the injected fluid at its breakthrough into the producing well is less than that expected based on information which neglects gravity effects. This difference can often be as much as 80 per cent by gas or water injection in uniform sand bodies. Preliminary flow tests on a non-uniform sand body indicate that the uniformity of the flood fronts may in some situations be influenced to a much greater degree by permeability variations within the rock body than by gravity effects. The magnitude of fluid segregation due to gravity is controlled by the average injection rate, rather than day to day or week to week variations. INTRODUCTION One of the important factors controlling the oil recovery from a frontal-drive operation, such as water, gas, or solvent injection, is the volumetric sweep efficiency. This factor is a measure of the gross portion of the reservoir that is contacted by the displacing fluid. The volumetric sweep efficiency is influenced by gravity effects, well arrangements, and variations in rock permeability within the reservoir. The gravity effects are due to the displacing fluid being of different density than the reservoir oil. This causes the displacing fluid to move preferentially toward either the top or bottom of the formation. Non-uniform advance of the flood front can be caused by the relative positions of the injection and production wells. Variations in rock permeability also result in an uneven advance of the displacing fluid. Gas zones, representing paths of low resistance, may result in non-uniform movement of the injected fluid. The more uneven the advance of the displacing fluid, the lower is the volumetric sweep efficiency and thus the lower the oil recovery efficiency. The effects of well arrangement and permeability variations, upon the gross movement of the injected fluid have been the subjects of extensive investiga-ti0ns.1,2,3,4,5,6 Gravity effects have been recognized as being present in frontal-drive operations'.' but there has been little quantitative measure of their magnitude. Very likely the reason gravity effects have not been studied is that this problem does not lend itself to simple experimental or mathematical analysis. The development of reservoir modeling techniques has made possible a quantitative determination of the effect of gravity on fluid segregation and thus upon the oil recovery performance of frontal-drive operations. This paper presents a progress report on a laboratory investigation of gravity effects in fully liquid-saturated, horizontal, uniform as well as non-uniform systems. These results were obtained from scaled experiments on both linear and five-spot systems within the range of conditions normally encountered in secondary recovery operations. This study is concerned with the gross movement of the injected fluid to the time it first reaches the production wellbore. Therefore, it should be emphasized that the results of this paper can not be used to determine the effect of gravity segregation on oil recovery efficiency at abandonment conditions. MODEL SCALING The science of scaling models is relatively new as applied as petroleum production problems, Many of the scaling techniques have been adaptions of those used in basic studies of heat and fluid flow. There are

Jan 1, 1958

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By William R. Barton

Iron and steel slag represent man's most successful attempt to date to profitably utilize a solid waste. Its consumption represents a solution to a solid waste problem and also represents tonnage of natural aggregates that will not have to be mined with concomitant disturbance of the land. Slag has been produced as long as iron has been made; but until a little more than 50 years ago, it was mostly a waste product to be disposed of with as little effort and cost as possible. Huge piles of waste slag were generated over the years of iron and steelmaking. Sporadic use was found for small amounts starting with slag (from Catalan forges) used for road bases by the Roman Empire. The first recorded sustained commercial use was, as is often the case in man's history, for making war. Some profit- conscious munitions maker in the 16th century realized that he could make cannon balls of slag instead of the more precious iron. Other small-volume uses gradually developed: cast building blocks, slag-lime mortars and cements, slag wool, ballast, road base, and, finally, in concrete. But it was not until after World War II that the true potential of blast-furnace slag as a construction aggregate was really recognized. Now nearly all blast-furnace slag produced is used, and much of the earlier stock- piles in the U. S. have been reduced or entirely consumed. Steel slag for aggregate use has been in commerce for only the past 10 years, and use has increased rapidly (10-50% per year) during the past 5 years as blast-furnace slag supplies became depleted. However, much remains to be accomplished in determining character and optimum conditions of use for various types of steel slags before such slags will realize their full use potential. Although slag represents only 2% of construction aggregate materials used in the U.S., its production involves certain features that make its production record far more important than national tonnage figures would indicate. Its source is in iron and steel production and concomitantly slag availability is restricted to those areas where iron or steel is produced. In such areas, it often represents one of the principal aggregates marketed and, because of special properties that make slag a selected aggregate for certain uses, the tonnage imbalance may be overcome by the importance of its contribution to quality or special characteristics of end products. The location and number (Fig. 1) of slag plants handling this annual production is governed by the geographic makeup of the iron producing industry. Prior to the period marked by World War 11, most blast furnaces were in the Great Lakes area-Pittsburgh, Cleveland, Chicago, Gary, Buffalo, Detroit, Youngstown, and Toledo, with exceptions at Baltimore, Bethlehem, and Birmingham. Since that time, iron and steel facilities have been established in Texas, Utah, and California. Today 85 slag plants in 15 states provide employment for almost 2000 persons. The slag plants also recover almost 4 million tons of slag-encrusted iron each year for return to the blast furnaces. Much of the success in developing uses for slag can be attributed to the efforts of the National Slag Association founded in 1918. Since then, it has conducted numerous field and laboratory investigations to demonstrate the properties and uses for slag and slag products. These investigations have resulted in total recognition of blast-furnace slag as a construction material of consequence. The American Society for Testing & Materials Designation C125 recognizes blast-furnace slag as "the nonmetallic product consisting essentially of silicates and aluminosilicates of

Jan 1, 1975

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,'' for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955

By T. K. Perkins, L. R. Kern

A study of fluid mechanics, rupture of brittle materials and the theory of elastic deformation of rocks shows that, for a given formation, crack width is essentially controlled by fluid pressure drop in the fracture. Operating conditions which cause high pressure drop along the crack (such as high injection rate and viscous fluids) will result in relatively wide cracks. Conversely, operating conditions which cause low pressure drop (low injection rates and thin fluids) will result in relatively narrow cracks. Charts and equations have been derived which permit the estimation of fracture widths for a variety of flow conditions and for both horizontal and vertical fractures. INTRODUCTION There has been considerable speculation concerning the geometry of hydraulically created fractures in the earth&apos;s crust. One of the questions of practical importance is the width of fractures under dynamic conditions, i.e., while the fracture is being created and extended. Such width information could be used, for instance, to help estimate the area of a fracture generated under various conditions. Also, there has been a recent trend toward the use of large propping partiles.13, 15 Therefore is is desirable to know what factors can be varied in order to assure entry of the large particles into the fracture. There has been some work on fracture widths reported in the literature. In particular, there have been several Russian publications dealing with this sub-jeCt.1.31,3 These papers have dealt principally with the elastic theory and the application of this theory to hydraulic fractures. These studies have not led to an engineering method for estimating fracture widths under dynamic conditions. A recent paper3 has reviewed and summarized the Russian concepts. An earlier paper- from our laboratories also discussed the application of the elastic theory to hydraulic fractures. This first approach, based largely on photoelastic studies, has proved to be too simplified to accurately describe the fracturing process. However, these early thoughts have served as a guide during the development of more exact concepts. We would like to present in this paper our current concepts regarding fracture widths and some estimates of hydraulic fracture widths for several conditions. We believe that it is now possible to predict with fair accuracy the factors influencing fracture widths. Furthermore, the method of prediction has been reduced to a simple and convenient graphical or numerical calculation. CRACKS IN A BRITTLE, ELASTIC MATERIAL Many investigators2, 4, 30 have shown that competent rocks behave elastically over some range of stresses. Of course, if the tensile stress imposed upon a rock exceeds some limiting value, then the rock will fail in tension. In similar manner, there are some limiting shear stresses that can be imposed upon rocks. Hubbert and Willis11 have discussed the shear conditions which will lead to failure. Under moderate stress conditions (such as those likely to be encountered when hydraulically fracturing) and when stresses are rapidly applied, relatively, most rocks will fail in a brittle manner. Hence, for this discussion of hydraulic fractures in the earth&apos;s crust, we assume the rocks behave as brittle, elastic materials. Let us develop the discussion in the following way. (The following thoughts are applicable only to brittle materials.) 1. First we consider a brittle, elastic system. An energy balance will show the minimum pressure necessary to fracture rock, and from this pressure we calculate the minimum crack width resulting from extension of a hydraulic fracture. 2. Then we will show that, under ordinary fracturing conditions, fracture widths are appreciably greater than the minimum widths of extending fractures. In fact, we will find that crack width is controlled by fluid pressure drop in the fracture. 3. We will discuss pressure drops in fractures and resulting crack widths for various operating conditions and both vertical and horizontal fractures. 4. Finally, we will discuss the significance of these concepts, their relationship to fracturing pressures, etc. First, consider minimum fracture extension pressures. We can shed some light on this question by considering the theory proposed by Griffith7, 8 Yo explain the rupture of brittle, elastic materials. Griffith recognized that solid materials exhibit a surface energy8 (similar to surface tension in a liquid). The fundamental concept of the Griffith theory is that, when cracks spread without the application of external work (in the interior of an elastic medium which is stressed

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.&apos; In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium&apos;s lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Extensive solid solubilities of CdTe (zincblende-type struckre) and InTe (B37 type) in each of the rock salt-type compounds, PbTe and SnTe, have been observed. Partial phase diagrams have been determined by thermal analysis and X-ray metallography. The limiting mol fraction. X,, of the solute in the rock salt-type a phase and the corresponding eutectic temperatures, T,, are: (PbTe)l-x(CdTe)x: X,- 0.2, T, =866°C; (PbTe),-,(lnTe),: X, - 0.35, T, = 646"C; (SnTe),-,(CdTe),:X,- 0.11, T, = 784 "C; (SnTe),-,(lnTe),: X,-0.53, T, = 630°C. The lattice parameters of the a phase decrease linearly with X, even in (PbTe),-,(CdTe),, where a, (CdTe) = 6.481A > %(PbTe) = 6.459A. This is taken as proof that the cadmium atom enters an octahedral interstice of the tellurium atom sublattice; i.e., the formation of the a phase entails the direct replacement of lead by cadmium. The a, us X curve extrapolates to 6.16A at X = 1, in agreement with the value predicted for an ionic crystal of CdTe; it is also consistent with the reported lattice parameter It is well-established that the compositions of intrinsic semiconducting and semimetallic compounds conform to normal valence rules.1"5 The apparent exceptions can be explained by taking account of anion-anion covalences, as in CdSb, or of multiple cation valences, as in In Te.&apos;This empirical generalization is the basis of the chemical approach to semiconductors2 by which the properties of an intrinsic semiconductor are rationalized in terms of the ionic-covalent bonds necessary to saturate the valence-electron complement of the anion sublattice. A fundamental shortcoming of this approach is its disregard of long-range crystal interactions. It cannot, accordingly, deal with the phenomenon of charge conduction except through the use of ad hoc postulates. As an example, a crystal of CdTe would, in the valence-bond picture: be described in terms of electron pairs, each with the same discrete energy, localized between every cadmium and tellurium atom. This is, of course, contrary to the Pauli of the high-pressure rock-salt form of CdTe, corrected for decompression from 36 kbar. The free energy of formation of the a phase of pure CdTe at room temperature is calculated from the phase diagram to be +10 kcal per g-atom, in accmd with the value calculated from the transformation pressure. The standard enthalpy is +13 kcal per g-atom, and the standard entropy is +9 eu. The latter value implies the formation of extra classical particles, such as vacancies, interstitials, or nondegenerate charge carriers, but these alternatives are not consistent with the semiconducting properties and the densities of the a phase. The extrapolated values of the lattice parameters of (PbTe),-,(lnTe), and Spectively, for the rock salt-type modification of InTe. The corresponding interatomic separation is intermediate between monovalent and trivalent indium. The qualitative implications of the results are considered from the viewpoints of both valence-band theory and energy-band theory. principle, and is corrected by methods of molecular-orbital theory in which bonds are replaced by bands of molecular orbitals whose energies, E, depend upon a crystal-momentum vector, k.7 Each band is derived from a linear combination of atomic orbitals with two electrons required to saturate each molecular orbital in the band. In a crystal of N atoms containing z atoms in its primitive unit cell, there are 2 N/z states per band which lie in a region of k space bound by the Brillouin zone. In an intrinsic semiconductor, the bands can be grouped into valence bands which are normally filled and conduction bands which are normally empty. If the highest valence band and the lowest conduction band overlap anywhere within the Brillouin zone, the material is rendered semimetallic. The quantity defines the effective mass, m*, of an electron in a conduction band (or of a hole, i.e., an electron deficiency, in the valence band) and leads directly to the concept of charge mobility through the relation \x = et/m*, where e is the electron charge and t is the lattice relaxation time.

Jan 1, 1964

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.&apos; It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By David R. Mitchell

THIS paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual,1 it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. HISTORICAL SUMMARY The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and sizing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By T. K. Perkins, O. C. Johnston

Because of the influence of dispersion on miscible-displacement processes, diffusion and dispersion phenomena in parous rocks are of current interest in the oil industry. This paper reviews and summarizes a great deal of pertinent information from the literature. Porous media (both unconsolidated packs and consolidated rocks) can be visualized as a network of flow chambers, having random size and flow conductivity, connected together by openings of smaller size. In such a porous medium, the apparent diffusion coefficient D is less than the molecular diffusion coefficient Do, as measured in the absence of a porous medium. For packs of unconsolidated granular material the ratio D/D, is about 0.6 to 0.7. For all porous rocks, both cemented and unconsolidated, the ratio of diffusion coefficients can also be represented as D/Do = 1/FF where F is the for- mation electrical resistivity&apos; factor and 4 is the porosity. If fluids are flowing through the porous medium, dispersion may be greater than that due to diffusion alone. At moderate flow rates the porous medium will create a slightly asymmetrical mix zone (trailing edge stretched out), with the longitudinal dispersion coefficient approximately proportional to the first power of average fluid velocity (if composition is nearly equalized in pore spaces by diffusion). If the velocity in interstices is large enough, there will be insufficient time for diffusion to equalize concentration within pore spaces. In this region, longitudinal dispersion increases more rapidly than fluid velocity. At low velocities in interstices, transverse dispersion is characterized by a region in which transverse diffusion dominates. If the fluid velocity gets high enough, there will be a transition into a region where there is stream splitting with mass transfer but with insufficient residence time to completely damp-out concentration variations within pore spaces. There are several variables that must be con- trolled to get consistent longitudinal and transverse dispersion results, viz., (1) edge effect in packed tubes, (2) particle size distribution, (3) particle shape, (4) packing or permeability heterogeneities, (5) viscosity ratios, (6) gravity forces, (7) amount of turbulence, and (8) effect of an immobile phase. INTRODUCTION Diffusion and dispersion in porous rocks are of current interest to the oil industry. This interest arises because of the influence of dispersion on miscible-displacement processes. In a recovery process utilizing a zone of miscible fluid, there is the possibility of losing miscibility by dissipating the miscible fluid or by channeling or "fingering" through the miscible zone. Diffusion and dispersion are two of the mechanisms that may lead to mixing and dissipation of the slug. On the other hand, dispersion may tend to damp-out viscous fingers which may be channeling through the miscible slug. 58 Hence, dispersion may be detrimental or beneficial (if it prevents fingering through the miscible zone). Therefore, it is doubly important that we understand these processes. In this paper we review, summarize and interpret a great deal of information from the literature. In particular, we will briefly discuss molecular diffusion in miscible fluids. Then we will discuss what differences to expect for diffusion in a porous rock. If there is movement of the fluid through the rock, then there may be an additional mixing or "dispersion". Furthermore, the dispersion longitudinally (in the direction of gross fluid movement) and transverse to the direction of fluid movement will not be equal. We will discuss both types of dispersion as well as several variables which can affect dispersion (viscosity differences, density differences, turbulence, heterogeneity of media, etc.). This group of variables has sometimes led to difficulty when comparing literature data. DIFFUSION OF MISCIBLE FLUIDS If two miscible fluids are in contact, with an initially sharp interface, they will slowly diffuse into one another. As time passes, the sharp interface between the two fluids will become a diffuse

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders&apos; wealth). This value or wealth is represented by the market price of the firm&apos;s common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm&apos;s common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market&apos;s perception of the company&apos;s progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm&apos;s stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company&apos;s stockholders and will have an effect on the market value or price of the firm&apos;s common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By S. H. Ash

Diesel locomotives, trucks, bulldozers, and other diesel-powered equipment are fast proving their superiority for mine transportation purposes. MORE than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance.1"0 This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago.7,8 Wumerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U. S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable. The best haulage equipment is subject to break- downs and accidents; but unless the rolling equipment, track, and signal systems are kept in good repair and are operated systematically, these breakdowns and accidents are likely to be frequent, destructive, and more costly than are necessary.10 Rail haulage crews using dependable rolling stock can move trips safely over grades low enough to be traveled without loss of control; this applies particularly if the track is straight and well maintained. Few accidents occur on main haulage lines if visibility and clearance are good and clear track is assured. One-way traffic underground is a recent development contributing to reduction of accidents and increased efficiency in mine haulage (Kelly mine, Anaconda Co., Butte, Mont., and Climax mine, Climax Molybdenum Co., Climax, Colo.)." Locomotives: Six types of mine locomotive used in recent years are trolley, storage battery, combination trolley and storage battery, diesel, compressed air, and gasoline. Electric haulage has been displaced by compressed air locomotives, which have been used successfully in certain instances, especially on dirty and wet tracks and steep grades." Maintenance cost is high, and operating efficiency, from a power standpoint, is low. Compressed air locomotives operate under self-contained power, and the absence of bare elec-

Jan 1, 1957

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,&apos;&apos; for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Wayne E. Glenn

The San Miguelito Field of Ventura County, California, lies along the coast approximately five miles northwest of the city of Ventura. The structure is one of several in the Ventura anticline, a series of anticlinal folds trending northwest-southeast through the San Miguelito Field. The Ventura Avenue Field lies to the southeast along the anticline, and Padre Canyon and Rin-con Fields lie to the northwest; the series then extends beneath the Pacific Ocean. Production is obtained from the Lower Pico and Repetto formations of Pliocene age, and oil accumulation is controlled by faulting, lithology and structure. The first well in the First Grubb Pool was completed in November, 1931, and to date 48 producing wells have been drilled on the 276 productive acres. Approximately 685 ft of net pay are contained in the eight sand bodies grossing 1,220 ft of section. Production of oil to date has been 15,-600,000 bbl. A gas injection project was instigated in April, 1940, but was discontinued in September, 1949. This paper is confined to a discussion of the development and performance history of the First Grubb Pool of the San Miguelito Field. LOCATION AND GEOLOGY The San Miguelito Oil Field is located in Ventura County about five miles northwest of the city of Ventura along the coastal highway to Santa Barbara. It is located within sections 23, 24, 25, and 30 of Township 3 North, Range 24 West, San Bernardino Base and Meridian. Surface elevation in the field ranges from sea level to plus 1,200 ft, and the terrain is extremely rugged. The structure is well defined on the surface and on the wall of the Amphitheatre Canyon where appears a so-called "text book" anticlinal section. The San Miguelito structure is an asymmetrical, elongated anticline about two miles long and three-fourths of a mile wide. The trend of the axis of the anticline is northwest-southeast. Fig. 9 illustrates the contours and major faults of this structure. Dips on the southwesterly flank average about 40 degrees, whereas the northeasterly flank ranges from 60 to 75 degrees. There are several faults striking generally east and west. These faults do not appear to affect materially the area of accumulation or performance behavior. It is believed that accumulation was affected by steeply dipping beds and extremely low permeability of the northeast flank of the structure. As shown by the typical log, Fig. 1. the San Miguelito Field is divided into two stratigraphic producing intervals. The First Grubb Pool comprises the interval from the "G" to "L" markers; the Second Grubb Pool from the "L" to "M" markers. The First Grubb Pool, ranging in thickness from 1,105 to 1,680 ft, with an average of 1,220 ft, includes approximately 685 ft of oil-bearing sands. The First Grubb zone consists of eight sand intervals separated by shales. The shale bodies separating the eight sand intervals within the First Grubb Pool are continuous throughout the major part of the structure and serve as an effective barrier. Many of the thin, irregular shale or siltstone streaks within these sand bodies are discontinuous and do not affect well performance appreciably. The productive horizons in the First Grubb Pool are siltstones and sandstones of the Lower Pico and Repetto formations of Pliocene age. It is apparent from inspection of the typical log that the "G" to "L" interval might have been separated into at least six producing zones and selectively pro. duced. Unfortunately the electric log and some of our modern tools were not available or were in their infancy dur. ing the period 1931 through 1937. Not until 1937 when eight wells had been completed were there sufficient geological data to permit definition of the sand bodies. Then the problem of reservoir control in this multiple-sand field, where all sands are open to a common

Jan 1, 1950