Search Documents

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By J. Leja, J. H. Schulman

FROTH flotation is usually effected by the addition of a collector agent and a frothing agent to an aqueous suspension of suitably comminuted mineral ores. The action of collectors is to adsorb onto the surfaces of minerals to be separated, sensitizing them to bubble adherence. The action of frothers has, in the past, been accepted as that of froth formation only, brought about by a lowering of the air/water interfacial tension. Substances capable of producing froth are classed1a,b according to their relative capacities for production of froth-volume and froth stability in the simple frother-water system. The purpose of this paper is to show that the surface active agents acting as frothers become effective only when there is a suitable degree of molecular interaction taking place between collector molecules and frother molecules at the air/water and solid/ water interfaces. Further, the discussion will demonstrate that the actual mechanism of adherence of an air bubble to a suitably collector-coated particle is due to the molecular interaction collector-frother. This leads to the formation of a continuous interfacial film of associated molecules, anchored to the mineral by polar groups of the collector, and enveloping the whole bubble. The tenacity of adhesion mineral-to-bubble results from the strength and the visco-elasticity of this mixed film.

Jan 2, 1954

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -The following report covers briefly some of the more important activities of the Institute during the year 1923 In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers, but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members The A. I M E has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American coun¬tries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging. From the quality point of view, the membership has not gone back¬ward. The Membership Committee has declined to recommend many

Jan 1, 1923

By Edwin Hopkins

The year of 1924, in Venezuela, has been one of especial interest. The figures for production marketed are not so impressive, but to the well-informed followers of the development, the ease with which this production has been obtained and with which it apparently can be increased at will merits most careful consideration. For several years, the oil world, especially in the financial centers, has been closely following the slow unfolding. of the' Venezuelan developments, which has been, and still is, one of the great pioneering achievements in the history of oil exploitation. Venezuela, from the first days of its recognition by geologists and financiers as a great future source of oil, has been a field for the enterprising vision of the larger capital groups. The laws of the country have been drafted with almost an inspired foresightedness that has favored the exploitation of the resources along constructive lines, which' has eliminated the irrational promotion schemes that accompany many of the oil developments in the United States. Developments have been exclusively in the hands of strong financial groups, who have followed a conservative policy with respect to the dissemination of detailed information concerning the geological findings and detailed production data. Within the last year, however, the rapid expansion of the production phase of the developments has been on such an important scale and has involved such a large and rapidly increasing personnel, that further restraint with respect to information of a general informative' nature can serve no useful purpose. Certainly, from the volume of references to Venezuelan oil affairs, which are now of almost weekly occurrence in the oil trade journals, the public must appreciate the fact that in Venezuela, and in the Maracaibo district in particular, a new oil region of the first magnitude is about to emerge from comparative obscurity and occupy a commanding position on the stage of world oil affairs.

Jan 3, 1925

By George A. Lamb

AMONG the main interesting developments in the coal market have been the changes that have taken place between the consumer groups. Important signs of these changes began to appear many years ago, but in a modest way, and were apparent only to the few fuel experts making broad statistical determinations. It is doubtful, however, that any of these experts appreciated the significance of their early findings, and perhaps none had the imagination to consider how extensive these changes might be eventually with respect to solid fuels sales and distribution. (Reference here will be principally to bituminous coal.) Railroad Fuel Major changes in coal use did become pronounced after World War II, and it did not take an expert to see what was taking place and how serious the impact was likely to be. First, was the case of the steam and diesel locomotives. The railroads had been considered the best coal customers; they were steady and large purchasers and usually paid a better price than most others. Railroad fuel provided the basic mine realization and it often was the source for operating cash during general market slumps. It was the outlet for 20 pct of the bituminous coal production, as much as 110 million tons in 1946.

Jan 2, 1957

By L. R. Budrow, R. T. Mishler

The Lucky-Tiger mine is a silver-gold property, situated at El Tigre, in the northeastern part of Sonora, Mexico, at an elevation of 6000 ft. in the Sierra Madre Mountains. It is 30 miles by wagon road from the Esqueda station on the Nacozari railroad. Since its discovery in 1903, the mine has produced forty million ounces of silver. The ore has averaged 40 oz. silver and 0.25 oz. gold per ton. Copper, lead and zinc have been of minor importance, having averaged 0.4 per cent., 1.1 per cent., and 1.5 per cent., respectively. The richness of the ore, combined with its occurrence in narrow veins, required the use of the more expensive methods. of mining. Geology Wall Rock The wall rock is rhyolite and rhyolite tuff, both of Tertiary age. In rare instances, post-mineral andesite dikes have been intruded along the veins. In the upper part of the mine, the walls were fairly solid. On the lower levels, the walls are usually cither kaolinized and soft or silicified and fractured, both conditions requiring closely filled stopes or much timber. Veins The veins have been deposited along fracture planes in the volcanics. There are three principal veins, about 600 ft. apart, all striking nearly north-south and dipping steeply to the west. Table 1 records the approximate dimensions and assay of the veins. Although the average

Jan 1, 1925

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1984

By Volker Weiss, George Sachs, AE. P. Klier

PHYSICAL chemistry contributes to the understanding and efficient operation of hydrometal-lurgical processes in many ways, among them by providing quantitative answers to the following questions. 1) Can a given chemical reaction or process be made to operate and. if so, under what conditions? 2) what are the' factors which determine the rate of the reaction and how can this rate be regulated in practice? Thermodynamics attempts to answer the first of these questions and kinetics the second. The answer

Jan 1, 1958

By Douglas Bunting

IN THE anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner's open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of .Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns etc. shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (1) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires are extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision f the most competent persons. Materials and supplies should be fur-

Jan 9, 1921

By D. Pearson

INTRODUCTION In 1975 278x10 3 tonnes of zinc was consumed in the United Kingdom, of which 69.3x10 3 tonnes was obtained from secondary sources. Of this secondary zinc 37.7x10 3 tonnes was used in brass making, the remainder was used in non metallic applications - eg oxides and salts. Many forms of zinc-bearing wastes arise, for example as galvaniser's drosses and residues, fumes from ferrous and non-ferrous metallurgical processes, and filter cakes from rayon manufacture and metal finishing. In the case of zinc-bearing dusts and fumes, the quantities available for recycle are at present restricted by the failure to collect them efficiently, hut environmental factors are leading to improvements in gas cleaning, with the result that quantities collected will increase and then exceed those required for the production of chemicals, so that some dusts may either have to be dumped or processed to metal. The recovery of zinc from steelmaking dusts is practised in W. Germany (1) and Japan (2) employing processes based on reduction in rotary kilns in order to produce sponge iron and a zinc- rich oxide suitable for feeding to the zinc-lead blast furnace. Although the zinc-lead blast furnace is the only zinc-making process used in the UK, no similar treatment of steelmaking dusts is carried out, a pilot scheme was tested by the British Steel Corporation, but development was abandoned for economic reasons. It appears to be cheaper to pelletise suitable dusts and export them for treatment elsewhere.

Jan 1, 1981

By David Cole

The appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent machine, or to do more work except by the use of superimposed decks, the latter having obvious disadvantages. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2. The old system accomplished stratification satisfactorily but has

Jan 1, 1915

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,1 and his experiments have been described and summarized by Richards1 White's contributions seem to have passed unnoticed by Fahrenwald, 2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,4 USSR; Anselm5 and Grunder,6 Germany; and Rose and Evans,[6] Great Britain.

Jan 5, 1958

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

C. G. Dunn (Generai! Electric Research Laboratory)— The author is to be commended on his attempt to calculate the residual strain energy from information on the dislocation density within the subgrains and a surface energy associated with the subgrains. However, much closer agreement between a calculated critical size of a nucleus and the observed size of grains that did not continue growing can be obtained if a reasonable correction is made in obtaining the energy of the surfaces of the subgrains. For example, since the sample is a single crystal with a cold-rolling reduction of 70 pct in thickness, one needs either an average disorientation for this or an average subgrain boundary energy rather than the 2.5 deg disorientation of a bent crystal, which was used by the author. From either the Laue photographs of the author or the pole density plot of Koh and Dunn 16 for a (113) [332] cold-rolled crystal the

Jan 1, 1961

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases. Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By W. A. Thatcher

Nearly three years of experience in Spanish Honduras has placed the writer in possession of many facts concerning its resources which may be of interest to the Institute. According to the most trustworthy surveys, Honduras is bounded on the north and east by the Caribbean Sea; southeasterly by the river Segovia (or Wanks), which flows into the Caribbean at a point called Cabo Gracias a Dios (Cape Thanks be to God), long famous as the favorite hiding-place of the celebrated pirate, Morgan ; southwardly by a corner of San Salvador, the Bay of Fonseca, and the Republic of Nicaragua; Guatemala and San Salvador form tile western boundary. It is one of the five republics composing Central America, has a population of about 310,000 and an area of 150,000 square miles, lying between the 13th and 16th degrees of N. latitude, extending from north to south 200 miles, between the Atlantic and Pacific, and 400 miles from east to west, between Guatemala and Cape Gracias a Dios. It is composed of 13 States or Departments, under one common law. The principal resources are valuable woods, hides, rubber, tobacco, coffee, fruit, cattle, silver and gold. It is of the mineral resources of the country that I will speak, calling attention to the most noted mines, and their relative position to Tegucigalpa, the capital. The introduction of foreign capital into the country dates back about eleven years, and to-day there are at least twenty-five well organized companies.

Jan 1, 1892

[ ]

Jan 1, 1938

By C. P. Watson

Economics has been defined as the useful application of wealth or material resources. The search of alchemists in the Middle Ages for s formula by which base metals might be transmuted into gold was no more intensive than has been the search by all branches of the oil industry for methods whereby the rnatcrial resources of West Texas in the nature of sulfur-bearing oil might be usefully applied. The purpose of this paper is to present in brief space developments that are conceded to possess economic significance. History The first discovery of oil in commercial quantities in the Permian Basin of West Texas was the Westbrook field in Mitchell County in 1920. Three years later the discovery well in the Big Lake field was cornpleted as a small pumper (70 bbl.) at a depth of 3028 ft. In 1925, discovery of the Powell or World pool in Crockett County stimulated activities in the Permian Basin, further establishing the importance of the Permian limestones as sources of production. The years 1925 and 1926 were marked by a period of extensive leasing and drilling activities. At the close of 1926 more than 7,000,000 acres had been leased and discovery wells completed in the Hurdle, Hendricksand Yates fields, definitely establishing the importance of the Permian Basin as a source of production from free-flowing wells. Review of Fields The producing fields in the Permian Basin are grouped on three distinct lines of folding. These may be separately identified as the Big Lake-Powell fold; the Yates, Hurdle, and Church-McElroy area and the Winkler County development. Production is derived from a porous limestone stratigraphically uniform, encountered at depths varying from 900 to 3100 ft. Lenticular sand bodies above the lime in Howard County have resulted in the

Jan 1, 1928