Search Documents

By F F. Pitard

The optimisation of a metallurgical plant requires two kinds of sampling systems. The first provides samples to follow process changes, so in due time actions to maintain key parameters within pre-established specifications can be applied. The second provides composite samples at the end of a working shift to demonstrate that valuable constituents sent to the plant went to either a final concentrate or to the tailings in a logical, expected proportion. Contrary to what many experts may claim, these two kinds of sampling requirements are incompatible and cannot be fulfilled using the same sampling systems; this is because the required samples have completely different objectives. A process control sample is an instantaneous sample with increments taken at short intervals, and the objective is to know where the process is at any given time. Excellent accuracy is not a must, however good precision is recommended since a possible process correction may need to be made. Online analysers fed with in-stream stationary cutters or other kinds of in-stream or by-stream probes can do well for such a mission. A composite sample for metallurgical accounting with increments collected over a long period of time, for which excellent accuracy and good precision are both required, must be generated by sophisticated and extremely well-maintained cross-stream sampling stations. The use of process control sampling systems to achieve good metallurgical accounting has been promoted by several manufacturers of sampling equipment around the world; it is a grave mistake that is misleading top management and a practice that should be scrutinised and preferably eliminated. Furthermore, bias tests used to prove otherwise are often based on insufficient data to draw valid conclusions; a guideline is provided.CITATION:Pitard, F F, 2014. Sampling systems for process control and metallurgical accounting, in Proceedings Sampling 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The 1999 edition of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves (the æJORC CodeÆ) became effective in September 1999 and is the latest revision of a Code which was originally issued in 1989, but which has an ancestry dating back to the first JORC report released in 1972. The modifications introduced in 1999, which are briefly discussed in this paper, substantially improved the document, but did not materially alter the fundamentals of the Code, these being the Mineral Resource/Ore Reserve classification framework and terminology, and the requirements and guidelines for public reporting of Resources and Reserves. Codes or guides similar to the JORC Code exist or are under development in other countries, including the United States of America, Canada, the United Kingdom and South Africa. It is pleasing to note that the 1999 JORC Code has been used as a model by these countries in developing their latest standards, and has been a major influence in the formulating of international reporting standards. The JORC Code is primarily a document covering the reporting of the results of mining companiesÆ activities to the public. However, mining geologists are interested in practical assistance and guidance in carrying out their duties. The JORC Code provides this in four ways. It establishes a framework within which those preparing and publicly reporting Mineral Resource and Ore Reserve estimates must operate, by setting standards for the classification and reporting of Resources and Reserves and for qualifications of Competent Persons. It establishes the division of responsibility between the companyÆs Board of Directors and Competent Persons with respect to the preparation and reporting of Resources and Reserves, and empowers Competent Persons to materially influence how their Resource/Reserve estimates are reported to the public. It provides an extensive, detailed and practical check list of criteria to be taken into account in the preparation of Mineral Resource and Ore Reserve estimates. Finally, it provides a strong measure of due diligence protection in the event of litigation if it is followed with diligence and honesty.

Jan 1, 2000

By R Long

The founder of social psychology is sometimes identified as Kurt Lewin. In a 1947 article, Kurt Lewin coined the term ‘group dynamics’. He described this notion as the way that groups and individuals act and react to changing circumstances. Lewin theorised that when a group is established it becomes a unified system with unique dynamics that cannot be understood by evaluating members individually. The discipline of social psychology really emerged out of World War II and tackled questions associated with human judgement and decision-making by the Nazis. For a comprehensive look at the development of social psychology look at Abelson, Frey and Gregg (2004).Social psychology is concerned with the way social arrangements affect human judgement and decision-making. What the author has done is apply the knowledge of this new discipline to an understanding of risk, safety and leadership. This paper will explain some of the developments in social psychology, such as the discovery of the bystander effect, Groupthink, bounded rationality, heuristics, risk homeostasis and the Milgram effect.The social psychology of risk tackles the way decisions are made about risk in their social context. Unless organisations understand that decision-making is socially conditioned, they are unlikely to be able to tackle the complexities of culture change or the development of risk maturity.The paper will offer a new understanding of why people do what they do, how risk makes sense and why a ‘dumb down’ approach to safety is dangerous. A model will also be presented that shows the pathway to risk maturity.CITATION:Long, R, 2016. The social psychology of risk, safety and leadership maturity, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 31–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Bishop D. J

The Imperial Smelting Process for the simultaneous production of zinc and lead is probably regarded by the ecologist as a necessary evil with the benefits of its products marginally outweighing the adverse effects of its operation. The purpose of the paper is to examine the environmental impact of the process and to provide information which will demonstrate that the process has considerable indirect environmental benefits and that success is being achieved in reducing direct pollution of the environment by the process. About 12 per cent of the world's zinc and seven per cent of its lead is produced by the process. This proportion will increase with the construction of a new smelter in China. After a brief description of the process the paper considers one of its principal advantages, its ability to treat bulk concentrates. The production of these at the mine can have a number of environmental benefits. Less comminution may be required to separate the metals from the gangue than is needed to separate them from each other; recoveries can be improved in flotation resulting in cleaner tailings dams, less power demand and reduced consumption of potentially hazardous reagents. Simplification of mining and above ground ore handling may also give significant benefits . The process is a considerable consumer of secondary materials such as galvanisers' ashes, copper smelter dusts and materials containing zinc and lead derived from steel plant dusts. The majority of these materials are fed to the blast furnace after hot briquetting. The consumption of secondary materials is a considerable environmental benefit since otherwise they would require to be dumped in secure land-fill sites. The operation of the process itself continues to be subjected to increasingly stringent environmental standards of which examples are provided. Details are provided of lead emissions at Avonmouth showing considerable success in reducing these while increasing production. The slag from the process continues to find many useful applications.

Jan 1, 1993

By Sparrow GJ, Woodcock JT

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t An, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5-40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects.Direct cyanidation for 48 h extracted only 26% of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77%. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88%, giving a tailing assaying 1.5 g/t Au.

Jan 1, 1990

By A Weston

Northparkes Mines is a joint venture between Rio Tinto and the Sumitomo group and is operated by Rio Tinto to produce copper concentrate from ore sourced from open cut and underground. Underground ore is mined with an owner operator workforce using the block cave method from the E26 deposit, with the first lift of the cave now completed. Development of the Lift 2 block cave commenced in March 2001 using a contract workforce. The Lift 2 Project required the mining of 14 700 m of decline and lateral development to establish a new mining horizon at the 9450 level and to develop two new conveyor declines. Also included in the scope was the excavation of a Crusher chamber to house the jaw-gyratory crusher. This paper describes the excavation of the hydroset chamber and orepass that sit immediately underneath the Lift 2 Crusher chamber. It includes risk assessment, planning, development of method statements and standard operating procedures, through to the excavation of the orepass and the installation of ground support in seismically active ground. There was a major ground failure in the backs of the conveyor feeder chamber during its excavation, which affected the excavation of the orepass due to its proximity to the breakthrough site.

Jan 1, 2005

By Rosenblatt M, Gilroy J. A C Cunningham C V B

Vaal Reefs Exploration and Mining Company Limited operates one of the largest producing gold mines in the world. The annual production of 76 tons of gold from 12 million tons of ore treated is obtained mainly from underground sources. Daily some 6.6 km of stope face is blasted and 41 tons of explosives is used to break the rock. The mine employs 45 000 men of whom 35 000 work underground. The company operates nine large vertical shaft systems of which seven extend more than 2000 m below surface and an eighth, currently being sunk, will bottom at 3700 m below surface.

Jan 1, 1995

By Greenwood-Smith R, Ellis W. K

A bulk analyser based on the gamma-ray resonance scattering process can be used to give a rapid and accurate measure of the percentage by weight of copper or nickel averaged over a large mass of sample, typi- cally 20 kg. It is shown that for a bulk sample containing about 3 wt.% Cu, crushing to -25 mm is the only sample preparation requited for analysis to within an error of about 0.06 wt.% Cu (errors quoted are one standard deviation). A comparison of bulk analyser and con- ventional assays on the same bulk samples can be used to estimate the sample preparation errors in the conventional methods. The squared deviations between bulk analyser and conventional assays are approximated by the sum of variances in sample preparation, conventional analysis, and bulk sample analy- sis. The sample preparation error was esti- mated as 0.26 wt.% Cu for samples crushed to -2 mm before splitting, 0.08 wt.% Cu for samples crushed to -0.35 mm before splitting, and 0.04 wt.% Cu for the average of 15 grab samples from bulk samples which had been crushed to -2 mm. The average copper grade for each group of samples was about 1.7 wt.%. Results are presented which show that

Jan 1, 1976

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

It is possible to closely simulate the product sizing distribution from an industrial rod mill by the correct choice of parameters in laboratory batch milling. For laboratory batch rod milling, changes in per cent critical speed and per cent rod volume cause the product sizing distributions to move in parallel at a constant slope. For ball milling, larger sized media in batch milling grind more coarse material giving a closer simulation to the industrial rod mill product. Changing the feed size distribution by removal of coarse particles or addition of fine particles changes the product sizing distribution, but would not normally be practiced in laboratory testing. These data should be applicable to many instances where laboratory simulation of an industrial product size distribution is required.

Jan 1, 1998

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011

Information obtained from a reconciliation system provides fundamental indicators to an operations performance and is often neglected as a key performance indicator when developing a business plan or mining schedule. The cycle of exploration, ore definition, mining and processing within a company is constantly scrutinised both internally and externally as to the safety, environmental and financial performance of these activities with the operators judged on their performance on a periodic basis. However, it is not unusual for the reconciliation process to be given scant attention until a serious issue (usually a shortfall) occurs, at which point short-term solutions may be implemented which only serve to compound the original problem. A robust reconciliation system takes time to develop and implement initially and must continue to evolve with time. The best systems are those where all the stakeholders in the ultimate outcome are involved in the design and accept responsibility for the validity of their component inputs. Output from the reconciliation process can be utilised to fine-tune all aspects of an operation once the underlying issues leading to a particular result are understood.

Jan 1, 2002

By A Giblett, S Hart

"In 2015 operations under the ownership and/or management of all Newmont Mining Corporation subsidiaries (Newmont) produced 5.7 Moz of gold and 619 Mlb of copper from mining operations in five countries, with well over 100 Mt of ore processed by various grinding technologies. Processing methods used in the extraction of metals include flotation, oxidation, conventional cyanidation and heap leaching. The grinding technologies applied in milling operations feeding metal recovery processes include conventional wet grinding semi-autogenous grinding (SAG), rod and ball, dry grinding, concentrate regrinding and ultra-fine grinding, and ball milling of high pressure grinding roll product. SAG/ball (SAB) configurations represent the dominant comminution flow sheet within the company and the circuit configurations employed include SAB, SABC-A, SABC-B and single-stage (SS) SAG milling, with SAG mill feed ranging from run-of-mine (ROM) ore through to secondary crusher product. The collective experiences earned from designing, operating and debottlenecking these various comminution circuits provide many lessons that can be applied to the design and optimisation of future operations. This paper provides an overview of Newmont’s diverse comminution circuits, discusses recent performance and offers some insight into optimisation and design considerations based on recent experience in both endeavours.Citation:Giblett, A and Hart, S, 2016. Grinding Circuit Practices at Newmont, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 293–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A G. Noble

Tunnelling for hydro-electric power projects can be a very challenging component of the overall development. In contrast to urban transportation tunnelling where the logistics for access and supply of power, water and other essentials are readily available, hydropower projects are usually in very remote locations and all necessary plant, equipment, spares and materials need to be brought in and the site must function as a self sufficient unit.For a large scheme the river diversion tunnel(s) are usually on the initial phase critical path in order to meet the non-negotiable deadline of river diversion before the onset of the wet season. A newly formed tunnelling crew, once mobilised to the site for the project, will face the first major learning curve of the project’s systems and logistics during this critical tunnelling activity.Power tunnels convey the water to the turbines in the powerhouse and are usually on the critical path for the main works, especially if the scheme comprises a powerhouse located within an underground cavern. A modern cavern arrangement requires a complex warren of various openings: access adits, ventilation/cable tunnels, shafts, surge tunnels, etc.Hydropower tunnel construction tends to be dominated by tunnel boring machine (TBMs) or drill-and-blast excavation techniques and each has its challenges in very remote locations. TBMs still have long lead times as for any type of project, but additionally require a thorough roads and bridges infrastructure assessment of the country from the port of entry to the site to ensure a problem-free delivery. In some cases the project also requires the establishment of a complete precast concrete segment production facility and the space for creation of laydown areas; there is no ‘just-in-time’ delivery mechanism applicable to typical remote hydropower sites.This paper highlights the technical and risk management considerations in the planning, design and construction of tunnels for hydropower projects. It contrasts the typical factors that govern the design of urban transportation tunnels with those for remote hydropower tunnels. The perspectives of stakeholders are provided including those of international lenders. With examples from large and small scale projects across the globe it provides an insight to all parties and in particular, those tunnellers that are working in the hydropower field for the first time.

Mar 8, 2011

Enhance Fine Particle Flotation by Hydrodynamic Cavitation Difficulties in fine particle flotation are well documented. Microbubble flotation has been found to greatly improve the recovery of fine particles and in situ gas nucleation by hydrodynamic cavitation incorporated in the design of modern flotation machines has shown great performance in fine particle flotation and potentially in coarse particle flotation. In this presentation, we will provide an overview on gas nucleation by hydrodynamic cavitation and its role in fine particle flotation with focus on the progress made in our research laboratory. Hydrodynamic cavitation was achieved and the critical role of dissolved gases in the liquid was elucidated by visualisation in a high intensity agitation cell. The in situ gas nucleation on fine particles by hydrodynamic cavitation was identified by zeta potential distribution measurement in model systems. Gas nucleation by hydrodynamic cativation was found to effectively aggregate hydrophobised fine particles thereby leading to enhanced flotation kinetics. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By Stevenson BG

The relevance of ore-dressing mineralogical investigations to developing and improving metallurgical flow-sheets is discussed and examples are given of the application of such studies to various types of ores and mill products (Au, Cu-Sn, Ni and Sn). The mineralogical investigations described illustrate (a) assessment of the feasibility of ore pre-concentration by heavy-media cyclone separation, (b) evaluation of the potential applicability of various metallurgical treatment processes to an ore, and (c) characterization of mill products to assess circuit efficiency and to guide circuit modifications.

Jan 1, 1978

By N Guresin, R Dunne, S Blanco

This paper presents the results of research work conducted to assess if aqueous solutions of sulfur dioxide (SO2) can be used to treat roaster calcine leach residues such that recovery of gold in this material can be achieved with subsequent application of the thiocyanate (SCN-) leaching system. The project is mainly aimed at assessing an alternative use for sulfur dioxide gas generated during flotation concentrate roasting. The calcine leach residue sample used in the study contained 2.56 g/t gold. The reason for this high level of residual gold is thought to be due to gold surface passivation by thin iron oxide films, presence of gold in solid solution with refractory iron oxides and encapsulation of gold in the structure of these iron oxides.The study was conducted in three stages. The first stage was the characterisation of a sample from a roaster calcine leach residue. The second stage in the project was a set of leaching tests to assess the feasibility of using aqueous solutions of sulfur dioxide to reductively dissolve refractory iron oxide mineral phases contained in the calcine. The final objective was to assess the efficiency of thiocyanate, a gold complexing ligand stable under acidic and oxidative conditions, to extract gold liberated during sulfur dioxide leaching.The study showed that the reductive sulfur dioxide treatment of the calcine leach residues followed by oxidative thiocyanate leaching to extract gold was not a particularly efficient process as only around 20 per cent gold could be extracted. Leaching the calcine residues by any of these systems separately also extracted the same amount of gold (12 - 14 per cent) implying that irrespective of the solution potential, the acidity helps dissolution of gold encapsulating minerals, mostly hematite, but at a very slow rate. The findings on the topic in the literature and during this study show the requirement for further technical investigations and economical analyses on two cases. The first case is to roast gold concentrates to produce magnetite rather than hematite followed by sulfur dioxide and thiocyanate leaching of magnetite containing calcines. The second case is to apply a magnetic concentration process to conventional roast-cyanidation calcine residues to produce a gold-rich magnetite concentrate that can be further treated with sulfur dioxide followed by thiocyanate leaching.For both cases, the best evaluation of the sulfur dioxide leach system in extracting residual gold from calcine leach residues will require a detailed economic analysis to find out the balance between the value of the gold recovered and the loss of revenue from acid production. There are a number of roasters that do not produce acid. In these cases, a portion of the unwanted sulfur dioxide gas can be used to recover gold in magnetite containing calcines as an economic incentive.CITATION:Guresin, N, Blanco, S and Dunne, R, 2013. Leaching roaster calcine leach residues with aqueous solutions of sulfur dioxide and thiocyanate, in Proceedings World Gold 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

NEARLY all problems in mining engineering involve the transport and distribution of materials from place to place, and in general the most economically managed mines and plants are those in which the transport of materials has been carried out most efficiently. Of all these transport problems, the hoisting of ore out of the mine and the distribution of same to the various treatment works is perhaps one of the most important. It is proposed in the present paper to traverse the conditions,affecting the location, scale of operations, and design of the main shaft and head gear at the Mount Morgan mine; afterwards describing the designs and workings of the shaft house, winding engine, and transport from the shaft house to the treatment works.LOCATIONWhen the copper-gold ore was developed sufficiently to determine approximately the boundaries of the ore-body, it was found that the existing vertical shafts would be wholly inadequate to deal with the increased quantity of ore required to be handled. It was proposed, therefore, to construct a new shaft, and to handle in this...

Jan 1, 1911