Search Documents

By Alexander RB, Hollis AJ

The magnitude of the payloads carried by mine haul trucks can have a strong influence on the mine production rates and costs. Consequently control of truck payloads is highly desirable, but in many mines the unavailability of means for measuring payloads reliably, accurately and easily has resulted in a low level of control over truck payloads. Consideration is given to two techniques which are applicable to the measurement of payloads carried by mine haul trucks, namely truck weighing and direct measurement of payloads with truck based systems. Accuracy assessments for two types of truck weighing platforms and two prototype truck based direct payload measurement systems are provided. Results show that weighing platforms based on hydraulic components have proved inadequate, while strain gauge type weighing platforms can estimate payloads to within 2% of true payload when installed, maintained and used correctly. The assessment of the two prototype truck based direct payload measurement systems shows that a high proportion of payloads were estimated to within 5% of the payloads derived from accurate weighing platforms and that these systems appear to have the potential to provide convenient and accurate measurement of payloads. This should enable payloads to be much better controlled than has been possible to date. Predictions of the effect of payloads on production rates and some components of truck haulage costs are possible and some typical results are presented. Accurate prediction of the effect of payloads are not yet possible for some major components of truck haulage costs.

Jan 1, 1986

By Osorio J. D C, McMahon M. D

Burwood Beach Sewage Ocean Outfall is being constructed by the Hunter District Water Board as part of an amplification scheme to eliminate pollution from adjacent bathing beaches. The outfall consists of a 93m vertical shaft, 1950m of 2.7m diameter tunnel with a series of diffuser outlets connecting the seaward end of the tunnel to the sea floor on a rock outcrop. The site of the work is in the Newcastle Coal Measures and the project is complicated by the proximity of colliery workings to tunnel alignment, although the colliery records provided valuable information on geological features. The location of the tunnel was determined to be in the Waratah Sandstone Formation immediately below the colliery workings after three different alternatives were considered. The shaft, which will be sized to suit contractor's construction methods and equipment, will be sunk through about 24.5m of alluvial material and 68.5m of rock. The tender documents were developed to allow the contractor considerable flexibility in construction method to suit available equipment. The specification also allowed great flexibility in tunnel construction method with minimum cross sectional area of 5.7m2 being the basis for a number of allowable alternative profiles ranging from circular to horseshoe.

Jan 1, 1987

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

By Kuwasaki N, Mitsune Y

Many activity measurements of components in liquid oxides have been reported in the field of slag chemistry. However, very little is known about the thermodynamic behavior of compo- nents in oxide solid solutions. In the present paper, e.m.fs. of the follow- ing galvanic cells employing solid electrolyte Zr02(CaO) were measured on the entire range of composition of the solid solutions. Pt/Ni-(Mgl-x ix)O/ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mgl-xNix)2SiO./ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mg l-xNix)Si03/ZrO2(CaO)/Ni-NiO/Pt. Activities of NiO in these solid solutions of (Mgl_ Nix)O and (Mgl_ Nix) 2Si0a(where 0

Jan 1, 1980

By Sans H

The geostatistical Discrete Gaussian (DG) model is demonstrated to be capable of providing an effective means of implementing change of support for Enterprise-style mineralisation and thus providing reliable global recoverable resource estimates. At Enterprise, sample grade distribution proves to be highly positively skewed, therefore significant deskewing of the histogram and reduction of variance occurs when going from sample to block support. The DG model was experimentally tested in'the Southern Primary Zone (SPZ) at Enterprise, where high anisotropy ratios and pronounced short range structures are observed in variograms. The experimental test was run for a change of support for which the variance reduction was. approximately 60 per cent. This reduction is similar to that predicted by Krige's Relationship ('the volume-variance relationship') for the practical situation of a change of support from 5 m vertical blasthole samples to 3 m x 8 m x 5 m selective mining unit (SMU) blocks. The DG model was found to correctly predict the grade tonnage relationships for a wide range of cut off grades. The experimental test indicated that, given a representative histogram and variogram, the DG change of support provides a computationally efficient and practical means of reliably assessing global mineable resources at the early stages of a mining project. Further, it allows a range of selectivity strategies to be meaningfully and comparatively considered prior to mining.

Jan 1, 1995

By R Whittering, C Greet

High chrome grinding media has been used in the mining industry for quite some time, as it often proves economical on a wear basis. However, it is unusual for an operation to change to high chrome solely due to its metallurgical benefits. KagaraÆs Mount Garnet operation made the change from forged steel to high chrome media after laboratory testwork indicated that copper grades and recoveries would improve. The outcome was remarkable with positive changes in pulp chemistry throughout the circuit accompanied by marked improvements in copper, lead and zinc grades and recoveries. Reagent dosage rates were reduced, often by more than half, and the grinding media wear rate dropped to less than a third of the wear rate of the forged steel media. The economic analysis showed that out of the total increase of revenue and savings from metallurgical improvements and reagent and media consumption reductions the metallurgical improvements made up approximately 73 per cent, the reduced reagents saved 25 per cent and the savings through reduced media wear contributing by just over one per cent. This indicates that the popular view of high chrome media only being trialled in the plant for wear economics is outdated and the focus of operations should be shifted to using high chrome media for the metallurgical benefits.

Jan 1, 2006

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

This paper explores the use of a Process Safety Management (PSM) system to manage risk in the mineral processing and metallurgical refining industries. Important elements of a PSM system are described. International regulations and non-regulatory guidelines covering PSM for high hazard industries are reviewed. Case studies of incidents in the mineral processing and metallurgical refining industries are presented to understand the lessons learned from failure to manage risks using a PSM system. Conclusions are drawn to adopt PSM in the minerals and metals processing industry as a tool for loss prevention and risk management.

Jan 1, 2003

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By Wharton C. L

This paper describes a new computer program which can significantly increase the Net Present Value of either an open cut or underground mine by optimising the cut-offs used during the operating life of the mine. It was developed over a period of about three years by Whittle Programming Pty Ltd of Melbourne, Australia. Several authors have contributed to the theory behind this work, but the ideas were further developed, consolidated, and clearly explained by Lane (1988). It was this book that triggered the development of the new program. The paper starts with an explanation of the theory behind this type of optimisation, and then goes on to describe the computer methods used to optimise the different parts of the problem.

Jan 1, 1995

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

The Ravensworth-Liddell area is part of the Muswellbrook- Singleton Coal District of the Northern Coalfield. It lies in the Parishes of Liddell, Ravensworth, Vane and Howick, in the County of Durham, midway between Singleton and Muswellbrook, and is traversed by the Great Northern Railway, and the New England Highway.Ravensworth and Liddell railway stations are 57 miles arid 61 miles, respectively, north from Newcastle (Fig. 1).The area has been the centre of an intensive search for open cut coal during the past few years. More than 1,200 bores, of which about 10% were cored diamond drill holes, were drilled to depths of about 200ft. Portions with thicker cover have been explored by 10 diamond drill holes to depths of over 400ft. but core recovery from these deeper holes was poor, and the lack of detail in the recorded logs limits geological interpretation. The drilling has proved about 34,000,000 tons of open cut coal, and about 246,000,000 tons under deeper cover.GEOLOGYThe Ravensworth-Liddell area lies on the eastern flank and southern extremity of the Muswellbrook Dome, extending from Hebden in the north, to Jerry's Plains in the south, and the rocks under consideration belong to the Tomago Stage of the Upper Coal Measures. On the north they are truncated by the Hebden Thrust fault, which has a throw of about 4,500ft. (Raggatt, 1929). On the west they are bounded by outcrops of the Upper Marine Series, which conformably underlies the Upper Coal Measures, and...

Jan 1, 1953

A new watersoluble binder for mineral ore pellets has been developed by the sulfonation of bituminous materials. A highly effective binder for iron ore pellet making is obtainable from bituminous materials produced in the hightemperature cracking of crude oils. This paper deals with production process and basic properties of this binder as well as new applications in the field of iron ore pelletizing.

Jan 1, 1974

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991