Search Documents

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H F. Galbiatti, G J. I dos Santos, A de C Zapparoli

The Grao Para and Rio Maria greenstone banded iron formations (BIFs), within the Carajas mineral province, exhibit distinct lithological and petrographic fabrics, together with pronounced differences in their surface expression, real thickness, iron grade and tonnage. These geological differences support a new model for the regional distribution of iron formations in the Carajas Mineral Province.

Jan 1, 2009

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Das

Deposit-10/11A is situated in the iron rich Bailadila region of India comprising haematite ore of average grade 65 per cent Fe. The deposit production line was commissioned in the year 2002 having a capacity of 5 Mt/a. The plant has the state of the art mineral processing equipments.The ore is transported from mines to crushing plant by means of dumpers. The ore is comminuted in two stages to get 150 mm top size product and this product is transported through conveyor system and is stored in silos as feed stock for beneficiation plant. In the beneficiation plant this crushed product is wet screened in two stages to produce a product of lump (-150 + 10 mm) and fines (-10 + 3.15 mm). The product of -3.15 mm top size is fed to primary classifier for a size separation at 150 µm. The resultant product (-3.15 mm + 150 µm) is dewatered and transported to fi ne ore product stock yard through conveyor system. The minus 150 µm material from classifier overflow is fed to cyclones (508 mm cyclone battery with an apex of 65 mm) for desliming at 45 µm and to recover ultrafi nes (-150 + 45 µm). The cyclone overfl ow slimes (-45 µm) along with water is treated in lamella thickeners to recover process water. The thickener underflow material is transported to tailing pond (discharge rate is 300 m3/h at a specific gravity of 1.4) by pumping through HDPE (high density poly ethylene) pipeline and the over flow water is being recirculated. The water requirement for beneficiation is approx 1.5 m3 per ton of ore.This paper aims at identifying and quantifying the factors that affect the overall plant performance (grade and recovery) during the different seasonal variations especially in the rainy season (mid-June to end October). The effect of seasonal variations on unit operations such as milling, classification, thickening and filtration are discussed. Specific cases are presented as examples and recommendations are formulated.

Jul 11, 2011

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Blair, T Scutts, L Fergusson

This paper presents a waste rock treatment and rehabilitation program conducted at a metaliferous mine site in northern New South Wales from 2000–2013. It updates findings from 2005 for Program #1 (which examined acidity, leachable metals and tree growth in a control and three treated areas of waste rock) and includes new results for Program #2 (which examined acidity, plant uptake of metals and trace elements and tree growth in a control and four treated areas compared to undisturbed background levels) and Program?#3 (which examined the treatment and revegetation of submerged mine tailings and an exposed tailings beach).Program #1 showed low soil pH in the control area remained unchanged from years 1–14, and soil pH in the limed and capped areas was initially increased but fell back to starting levels within 12 months and remained low for 14 years. In contrast, soil pH in the Terra B area resulted in soil high pH immediately after treatment and increased in years six and 14 without further treatment. Tree height and density in 2005 and again in 2013 indicated acidity in the control, limed and capped areas suppressed tree height and density; however, in the Terra B area, revegetation in 2013 was comparable to undisturbed forest. Outcomes in the control, biosolids and three Terra B areas in Program #2 were similar to those observed in Program #1.Program #3 showed the submerged and exposed tailings initially had low pH and high concentrations of total and leachable metals before treatment, but these became non-leachable after treatment with Terra B. Revegetation was achieved on the tailings beach, with almost uniform colonisation of bulrush and common reed, along with bottlebrush and golden wattle; a variety of reptiles have also been observed on the revegetated tailings beach, along with migrating ducks, spoonbills and grebes.CITATION:Fergusson, L, Blair, D and Scutts, T, ?2014. Treatment and rehabilitation of acidic waste rock and tailings – a 14-year case study, in Proceedings Life-of-Mine 2014 , pp 247–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable discharge. The simplicity and reliability of properly designed gravity discharge backfill tank systems suggests increased application of this technology by the mining industry.

Jan 1, 1998

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By J Vann

Geometallurgy is inherently multidisciplinary and it gains its power to deliver improved outcomes for the minerals industry by bridging silos between disciplines. This cross-disciplinary approach unlocks value, identifies (and avoids) value destruction and provides a pathway to better implementation of an energy efficient and sustainable minerals industry. Despite this promise, we argue that the cross disciplinary approach also represents the greatest threat to the success of geometallurgy. Some key cross disciplinary issues identified are:Geometallurgy has so far evolved in the technical sphere, mainly by collaborations of geologists and metallurgists. Consequently, in many cases the business dimensions and value have not been incorporated. Financial and risk evaluation viewpoints need to be assimilated into the geometallurgical paradigm. In fact, until such measures are integrated into practices, the value cannot be fully demonstrated.The historical and current efforts on geometallurgy have been highly focused on improved sampling and measurement of geometallurgical properties or appropriate proxies. This work has been driven by professional and academic geologists and metallurgical engineers. It is notable that mining engineers (who are critical in the value delivery of geometallurgy through changed planning approaches) have so far been at the margins, or absent. The construction of valid three dimensional (3D) geometallurgical models raises some important organisational, mathematical and geostatistical considerations. The enhancement of resource models to account for geometallurgical aspects must be managed carefully if the full value of geometallurgical thinking is to be realised.The use of 3D geometallurgical models to change business decision making and practices is the real nub of the problem. We believe sophisticated scenario based evaluation methods are required if the potential impacts of spatial rock properties on processes further down the mining value chain are to be realistically evaluated. Such changed practices require ‘whole of value chain thinking’ to embed this change into the business in an ongoing way.Because profitable geometallurgy demands changed approaches to business decision-making and also organisation of the firm (radically changed in some cases), the senior executive viewpoint must be incorporated into the language and thinking of geometallurgy. This is unavoidable if the establishment of a geometallurgical approach to project evaluation, development and operation is to be successful and sustained.A powerful analogy for the problem faced by geometallurgy is the transformation of safety culture in the mining industry in the past 20 years. We argue that, as in the safety revolution, explicit models, cultural change and management of the ‘soft’ dimensions of the problem are pivotal to success of geometallurgy. In light of this, we propose a model (‘the Geomet Curve’) that gives a framework and pathway for geometallurgy in seven steps. The implications of this model for technical and organisational steps required at different stages are discussed.

Sep 5, 2011

By A Giyose, V Malysiak, K Davey

Batch flotation tests were conducted on a haematite-bearing Sishen iron ore slimes sample from South Africa using reverse cationic flotation. The effect of grinding on flotation performance, the flotation response of various key impurities in the sample, and the feasibility of increasing metal recovery by refloating tailings in a scavenger flotation step were investigated. The test results indicate that reverse cationic flotation is effective in rejecting impurities from the iron ore sample tested. From a head grade assaying 6.4 per cent SiO2, 2.14 per cent Al2O3, 0.402 per cent K2O, 0.082 per cent P and 0.194 per cent TiO2, the levels of impurities were reduced to 1.83 per cent SiO2, 0.88 per cent Al2O3, 0.095 per cent K2O, 0.066 per cent P and 0.174 per cent TiO2 in the final concentrate at a Fe recovery of 74 per cent. The flotation response of SiO2, Al2O3 and K2O were found to be better than that of P and TiO2. The testwork demonstrated that grinding to 80 per cent passing about 49 microns is essential for upgrading the Sishen iron ore to produce >67 per cent Fe concentrate grade. This grind size corresponds to about 80 per cent liberation of haematite from the gangue minerals. Fe recoveries up to 76 per cent were obtained by refloating the rougher tailings in a scavenger stage, with little effect on the final concentrate grade. Size-by-size Fe recovery data obtained indicated that particles below ten microns were mostly lost in the desliming stage conducted prior to flotation whilst some reported to the froth by entrainment. Some of the coarser haematite-gangue composite particles reported to the froth product by genuine flotation.

Jan 1, 2009

By C Bartle

In many operations the use of less electrochemically reactive grinding media in the first grinding stage (for example, rod milling and high aspect ratio SAG milling) is rarely considered. Therefore, in reality a plant may inadvertently be using a 'mixed' media charge. That is, whilst employing inert grinding media during secondary grinding, electrochemically active forged steel grinding media may be used in the primary grinding stage. This paper discusses the impact of such a circuit on the pulp chemistry and flotation response of a refractory gold ore. The Wiluna concentrator has two grinding circuits operating in parallel. Line 1 operates a single ball mill in closed circuit with cyclones, and utilises high chrome grinding media, while the second circuit (Line 2) consists of a rod mill (with forged steel rods) in series with a ball mill, which also utilises high chrome grinding media. The cyclone overflows from both circuits are combined to feed a sulfide flotation circuit. Pulp chemistry surveys were completed around both grinding circuits, and laboratory flotation tests were conducted on the cyclone overflows. The results demonstrate clearly that the rod mill/ball mill circuit operated at significantly lower Eh and dissolved oxygen values, while the percentage EDTA extractable iron was considerably higher, when compared to the single stage ball milling circuit. These variations in pulp chemistry had a marked negative impact on the laboratory rougher flotation response, and suggests that plant performance may be affected.

Jan 1, 2008

By C J. Unger, A M. Lechner, A Walton, V Glenn, M Edraki, D R. Mulligan

In Australia, responsibility for abandoned mines can be unclear. With a few exceptions, state and territory governments have become responsible for abandoned mines on Crown land and private landholders are responsible for abandoned mines on freehold land. Abandoned mines pose risks and opportunities across the full suite of sustainability themes (environmental, human health and safety, socio-economic and community development) after mining ceases.Across Australia, there are more than 50 000 abandoned mines recorded, ranging in size from individual shafts to large polluting open cut mines. Addressing the safety and environmental impacts of these sites, as well as the socio-economic development opportunities of significant rehabilitation projects, requires the implementation of effective policies and programs. Qualitatively defined graded scales or ‘rubrics’ have been used for many years in student assessment and increasingly in the performance assessment of other sectors (Davidson, 2005). While risk-based maturity models have been used for safety prioritisation (Westrum, 1993; Hudson, 2007; DRET, 2008; Hancock, 2010) and evaluation of organisational development (Esteves et al, 2010), this paper is the first to adapt maturity models for the evaluation of abandoned mine rehabilitation programs in Australia.In this paper, we used indicators based on the national policy for abandoned mines to assess the maturity of abandoned mine programs. Fourteen elements of maturity were identified (Unger et al, 2012) under the five chapters of the national policy for abandoned mines (MCMPR and MCA, 2010). Jurisdictions were then evaluated and ranked on their maturity on the basis of information that was web-accessible. Information transparency of abandoned mines policies and programs is in itself one element of the maturity chart. Each jurisdiction in Australia was compared with one another and with a Canadian jurisdiction; the British Columbia (BC) Crown Contaminated Sites Program (CCSP), which represents leading practice (Unger, 2009; Unger et al, 2012).Our research found that in some jurisdictions in Australia there is little or no information on abandoned mine programs or individual abandoned mine sites on government websites, while other jurisdictions provided very detailed program information on planning, funding and implementation. Each jurisdiction in Australia, for which web-based information was available, had some elements where they were more mature than other Australian jurisdictions. For some elements, maturity ranked equivalent to the BC CCSP, but most Australian jurisdictions were less mature. There was only one element where a single Australian jurisdiction ranked higher than the BC program in maturity. Legacy mine policies, programs, priorities and funding information via departmental websites are easier to find in some jurisdictions, indicating progression toward greater transparency and more mature programs. A systematic approach to monitoring and evaluating abandoned mines programs is essential for accountability as it can demonstrate liability reduction over time and continual improvement. The maturity model approach can provide both a measure of progress over time as well as a tool to support the implementation of the national policy for abandoned mines (MCMPR and MCA, 2010).CITATION:Unger, C J, Lechner, A M, Walton, A, Glenn, V, Edraki, M and Mulligan, D R, 2014. Maturity of jurisdictional abandoned mine programs in Australia based on web-accessible information, in Proceedings Life-of-Mine 2014 , pp 467–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023

By P Cesare, S Munro, D Wandel, R A. Bearman

Consideration of the processing plant operational envelope is a key factor in production scheduling,and therefore mine planning, for any mining operation. In many cases hard-wired or regressionbased tonnage-grade-recovery relationships are used as mine planning constraints and as a means of valuing the system output. In extensions of this type of approach, various regressions can be used to describe throughput limits, based on a number of global metallurgical parameters.The ultimate position for the optimisation of a mine plan and production schedule is to have a full process plant model running as an integrated part of the mine planning exercise. A plant model suitable for this needs to have all the required sensitivities to input parameters such asfragmentation, grade, mineralogy, strength and hardness. The model then needs to convert these to performance measures for the plant, which include recovery, throughput, product size distributions, energy consumption, water use and operating cost.In this paper an approach is outlined that takes this view and then goes beyond it to provide a full, time-based bottleneck identifi cation and valuation tool.Using such an approach it becomes possible to run mine plans and production schedules in windows of days, weeks, months and over the life-of-mine with a time-enabled process model acting as the active constraint. In this way virtual bottlenecks can be identifi ed for various mine plans and schedules well ahead of time. The value of de-bottlenecking can be defi ned, not just at a plant scale, but in terms of the overall mining operation, and the data can be used as the basis for capital investment decisions.CITATION:Bearman, R A, Cesare, P, Munro, S and Wandel, D, 2014. Incorporation of a full process plant model as an active constraint for mine planning and production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

By J Berg, M Hahn, R Winkel

Imaging sensor systems designed for the mining and minerals industry incorporate different physical measurement technologies that can be used to detect the machine environment, such as laser, ultrasonic/sonar, video and RF-sensors. The underlying physical measurement principles cannot be employed in most applications near the face without regular maintenance due to the harsh environmental conditions like dust, dirt or moisture. However, that is the area, where imaging sensors are most valuable to the machine operator. In the domain of 2D radar sensors these have been either restricted by the angular coverage area or by limited adaptability of signal processing algorithms. The unique full digital solid state design will establish a generation step in mining applications.In order to fill this gap of terrain imaging sensors, the Institute for Mining and Metallurgy Machinery (IMR) of the RWTH Aachen University, in cooperation with the radar company indurad, developed an imaging sensor based on radar technology employing the digital beam forming (DBF) concept. Through multiple transmitting and receiving antennas the sensor delivers high accuracy range and angular information. Using adaptive digital signal processing with multiple imaging algorithms and target detection routines, data of the surrounding environment can be used to enable automation functions in mining.A comprehensive range of radar scans in different environments have been evaluated and benchmarked by using laser scanners. Accuracy measurements in range and angular direction have shown minimal differences. Experimental measurements have been performed at slopes, on conveyor belts and hot cement clinker silos. The experimental system uses a frequency modulated continuous wave (FMCW) front-end combined with a processing unit for signal analysis and target detection.

Sep 26, 2011