Search Documents

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

Gold rooms represent a high security area and preventing theft is a challenging task. Where gravity concentrates or high value unit intermediate products are present, particular and specific security procedures must be put in place. This paper describes the development and implementation which reflects best practice in gold room security. Procedures involving key holder systems, key locks, swipe cards and double locks preventing any one person having access to the gold room, including specific procedures for gravity gold concentrators, will be addressed. The use of monitoring and how to deal with alarms and potential hold ups will be reviewed. The use of cameras and archival DVD recorders is common in gold rooms. The use of electronic surveillance, movement detectors, seismic monitors and the two person policy and gold room entry procedures are described, including how to deal with visitors. The importance of confidentiality regarding smelting and gold pick-up days, plus strategies employed to minimise storing large quantities of gold on site will be presented. The role of metallurgical accounting in providing quality auditable information and the minimum standards of record keeping required is discussed. The role of the Gold Squad will be outlined. Regular auditing and risk analysis and several case studies are cited where security was deficient or improved.

Aug 1, 2010

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By P G. Bourke, A Yáñez, G J. Jameson, N M. L Kupka

The kinetics of fine and ultrafine particles in conventional mechanical flotation cells are limited (Feng and Aldrich, 1999; Trahar, 1981; Wang et al, 2016). Accordingly, even limited recoveries with such machines require long residence times. Theoretical investigations into the rate of capture of fine particles by flotation, have indicated that a key parameter is the rate of shear in the fluid surrounding the bubbles and the particles. Achieving fast flotation rates of ultrafines requires a new method of bringing the particles and bubbles into contact, utilising the beneficial properties of highly dissipative flows to break through the water boundary layer. In 2010, a new type of flotation cell known as the Concorde Cell was described, in which bubbles and particles are brought together in a sonic shock wave (Jameson, 2010). Earlier research had shown that when a dispersion of fine bubbles in liquid passed through a converging nozzle at the local speed of sound, the resulting shock wave downstream generates a mass of even finer bubbles in the flow as it passes through the shock wave. The fluid within the shock wave is highly turbulent, and an environment is created that is very favourable to particle-bubble collision and capture. In this paper, we briefly describe the Concorde Flotation Cell and give examples of its use.

Aug 24, 2022

By O Bøckman, E Thisted, K H. Esbensen, U Thisted

Process industry measurement systems, once installed, are often interpreted as static black boxes delivering correct values as long as not proven otherwise. After first implementation and set-up with a distinct sampling frequency, they often run ‘forever’ without checking if this frequency is still appropriate with respect to changed raw materials characteristics, different process conditions or changed customer specifications. Failure detection is based on operator experience and skills (often close to an art form) and/or from control measurements of reference samples. This may well be too late for many industrial process contexts. An appropriate sampling frequency is a critical success factor for valid monitoring and control.Based on the methodology of variographic analysis we here illustrate how to design/re-design/optimise an industrial measurement system in terms of sampling frequency, discretisation and accuracy based on customer specifications. We also show how variographics can be used to monitor for deviations. We use experience from process industry to show how these methods can be used not only for product characterisation, but also for monitoring input factors, process indicators and measurement of these. The information hidden in the vast amounts of data that is continuously created in modern process industries can be utilised to cut costs in the measurement activities and at the same time contribute to early error detection. We illustrate by case examples from production processes at a nickel refinery, supporting the Lean and Six Sigma methodology. This will provide a standard operating procedure for monitoring the stability of measurement systems, and provide a basis with which to discuss how a variographic approach can be integrated with the Lean and Six Sigma approach as an online tool to map, characterise and validate measurement systems and thus avoid more cumbersome measurement system analysis in full detail.CITATION:Thisted, E, Thisted, U, Bøckman, O and Esbensen, K H, 2017. Variographic case study for designing, monitoring and optimising industrial measurement systems – the missing link in Lean and Six Sigma, in Proceedings Eighth World Conference on Sampling and Blending , pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K T. Broekman, R L. Koenig

"The Braemar Iron Formation is atypical ore when compared to the current magnetite ores being processed. In attempting to process and economically recover the vast quantities of iron ore stored within the Braemar Iron Formation, æshifting the paradigmÆ is required. The formation has a low Davis tube recovery (DTR) grade of 15 - 20 per cent, which is much lower than magnetite ores processed in Australia. Despite this, by thoroughly testing and understanding the ore characteristics, it is found that the Braemar ores have significant advantages to processing than the harder banded iron formation (BIF) and taconite resources.The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. The grade was low and the Pilbara region discovery lead to the development of high-grade direct shipping hematite ores. Carpentaria Exploration (CAP) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. Shifting the paradigm away from grade the advantages of processing this ore are achieved by having an extremely low waste to ore ratio, lower Bond work index, lower abrasion levels and high-grade magnetite concentrates with little impurities other than silica. While developing the Hawsons Iron Project (HIP) it became more apparent that a positive business case is achievable when the following factors are exploited: very large resource - the resource is contained within one pit the rock fractures easily along grain boundaries - ideal for cheap impact crushing of the ore the ore is extremely soft, with a Bond work index of 6.3 - 8.0 kWh/t all major infrastructure required is readily available - rail, power, access and port the mine is in close proximity to Broken Hill - rich mining history and skill set available the resource contains many billions of tonnes of magnetite mineralisation.Shifting the paradigm by selecting equipment suitable for processing soft ores and not hard BIF or taconite ores and taking locality and available infrastructure into account may change the way people approach new low-grade resources in future.CITATION:Koenig, R L and Broekman, K T, 2013. Understanding ore characteristics and equipment selection, in Proceedings Iron Ore 2013, pp 403-410 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

By D Veneziano, J Van Dyck, R Snow, W Pytel, O Zanoli

Best practice standards generally recommend assessment of the environmental and societal risks posed by tailings storage facilities, but they rarely specify how the analysis should be made. As a case study, this paper describes a safety assessment of the Zelazny Most tailings pond operated by the Hydrotechnical Unit of KGHM Polska Miedz SA in Poland. The complete assessment includes a failure mode effect criticality analysis (FMECA) that considers all conceivable failure modes, but this paper focuses on one key mode, the loss of stability during the planned raising of the crest above its current level. Reliability against static dam failure considers uncertainty on the safety factor in a limit equilibrium approach. The threat of dynamic (earthquake induced) instability is assessed by developing a model of future seismicity as a function of the mining plan and considering uncertainty on the induced permanent displacements along critical sliding surfaces. We quantify the additional level of protection against outflow provided by the beach using an event tree with expert-assigned probabilities. Continuous monitoring of the dam for premonitory signs of instability and a set of loss-prevention plans in the case of a spill provide additional layers of protection; their effectiveness is quantified by estimating the fraction of the population that could be evacuated as a function of warning time. The probabilistic analysis indicates that the safety targets are met and produces practical recommendations on how to maintain and improve the safety level while the dam crest is raised above its current level.CITATION:Van Dyck, J, Pytel, W, Veneziano, D, Snow, R and Zanoli, O, 2015. Safety of a tailings storage facility against dam instability, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 253–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A M. Sardo, D E. Sinnett

This study uses the Q Method to examine how those living in former metal mining landscapes value this heritage and their preferences for the long-term management of mine waste. Such sites are often perceived as derelict or degraded, and of very little value. It is therefore assumed that their reuse, for example for development or recovery of metals, is likely to be beneficial. There are around 5,000 former metal mines in England and Wales, many of which are protected for their ecological, geological or cultural value. The Q Method is particularly suitable for issues where there is no consensus of opinion. We asked 38 residents of six mining areas in England and Wales to ‘sort’ a series of statements based on their resonance with the resident’s perspective; this is the Q sort. The statements covered a range of opinions of the mining legacy, its value and options for its management with a particular focus on the potential for metal recovery from the wastes. Analysis of the Q sorts revealed five perspectives on the mining heritage. All placed a high value on the cultural and ecological value of this heritage, however, they differed in their priorities for long-term management. For example, emphasis was placed on either nature conservation, cultural heritage, water quality or the opportunity for job creation through reworking the mines. Cutting across these themes there were also differing perspectives on the role of experts and local people in shaping the future management of the wastes. This research suggests that the views of local people are nuanced; they value their mining heritage but opinion is split on the most effective way to manage these sites especially where there is an impact on water quality.CITATION:Sinnett, D E and Sardo, A M, 2018. Former metal mining areas in England and Wales – local residents’ preferences for the management of wastes, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 126–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Gill, A Mathias

The mining industry has always been cost-focussed but in recent times mining companies have moved towards obtaining a competitive advantage through the implementation and sustainability of best practice in the areas of improved safety, operating costs, quality and productivity. This is the concept of Value In Use û that mining companies see value generated all the way to the bottom line through improved change, and those changes become an established mine practice. Many mining companies do not have the resources or the knowledge to sustainably achieve such an outcome. This has led to companies looking to their suppliers to deliver measured value to their business through partnership arrangements. Suppliers have been able to leverage their knowledge of products, product applications and services to offer alternative supply agreements that bring greater returns to their businesses while improving supplier/client relationships. Orica has developed such a partnership with Coal & Allied in the form of a Continuous Improvement Program. Coal & Allied is based in the Hunter Valley region of NSW and is the largest coal producer in that region. Both parties are contractually bound to jointly deliver Value In Use projects to Coal & AlliedÆs Hunter Valley Operations and Bengalla mine sites. It is the request of the Orica and Coal & Allied Steering Committees that this paper does not include the details of actual projects or the costs or key performance indicators associated with the program. This is to maintain the competitive advantage to both Orica and Coal & Allied through the implementation of such a program. It is in the writersÆ opinion that this paper does not lose any significance through this restriction as the most important component of the Continuous Improvement Program is not the projects themselves but the methodology behind them. With this in mind the paper will discuss the development of Value In Use offerings, the key aspects of the Coal & Allied and Orica joint program, what is a Value In Use project, how to measure its value, finally why and even more importantly what makes this program is a success.

Jan 1, 2004

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

By H W. Wu

Occupational exposure limits for diesel particular matter (DPM) are progressively being adopted in a number of countries. Many of these follow the lead of the US Mine Safety and Health Administration initiated in 2008. In line with adoption of best practice it is accepted that all exposures should be reduced to as low as reasonably achievable. The management of diesel emissions and occupational exposures to those emissions requires an integrated strategy incorporating efforts from all key departments on a mine, including management, production, maintenance, supply and occupational health and safety.Australian coalmine longwall moves rely on the use of high-powered diesel equipment such as chariots and other machines that produce exhaust pollutants of gases and DPM. To reduce mine personnel’s exposure levels to DPM a hierarchy of controls can be followed. Minimising the use of diesel equipment, better operator positioning in relation to exposure source, using efficient engineering methods and adopting better ventilation to reduce concentrations through dilution are some of the controls that can eliminate exposures. Approaches generally adopted in Australian longwall mines currently rely on a combination of strategies such as optimisation of ventilation, use of diesel particulate filters and use of diesel tag boards that minimise the number of vehicles through recording entry and exit into working panels.A study has been undertaken into the mine ventilation systems currently in use during longwall moves within Australian modern longwall extraction mines. This paper reviews current longwall section ventilation systems and discusses evolving changes being adopted to address the more complex problems in dealing with section DPM during phases of the operational moves. The effects of DPM on crew members as well as the diesel equipment operators within a longwall section are examined. Issues that should be considered in designing the longwall section ventilation during the moves are discussed.CITATION:Wu, H W and Gillies, A D S, 2015. Review of ventilation optimisation strategies during longwall moves, in Proceedings The Australian Mine Ventilation Conference, pp 133–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Y Cao, J C. Tien

Occupational health and safety is essential in modern mining workplaces and in China it is often not given enough emphasis due to a lack of knowledge and/or appreciation. Although many health and safety regulations have been passed over the years, serious and relevant laws and regulations on mine health and safety are of recent history (since 2002), the level of stringent enforcement is still inconsistent and accurate field data are scant and not readily available. As of year-end 2006 there were 676 562 recorded cases of occupational diseases in China, of which 616 442 or 91 per cent were miners’ pneumoconiosis. Of these, 146 195 (23 per cent) have died, and an average of 10 000 new cases were added every year between 1991 and 2006. Another report shows that 93.18 per cent of miners have never had a contract with their companies, which means their cases were not even part of China’s official statistics. This study attempts to examine the prevalence of occupational diseases in the Chinese mining industry during 2000–2013, compiled from government annual reports and academic studies. The research will review the correlational analysis among occupational diseases, ventilation practices, protection devices and legislation.CITATION:Cao, Y and Tien, J C, 2015. Occupational diseases in China, with the emphasis on its occurrence in Chinese mine workers, in Proceedings The Australian Mine Ventilation Conference, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By V Lishchuk, C Lund

"Geometallurgy aims to improve resource efficiency by creating a spatial model of an orebody in order to forecast ore processing behaviour. This enables calculation of the economic value of each ore block and the use of this information for production optimisation and hence an improved economic return. Modelling uses different approaches to link geological information with mineral processing: traditional approach uses chemical elements; proxy approach – small-scale geometallurgical tests; and mineralogical approach – minerals.A geometallurgical model is obtained during execution of a geometallurgical program encompassing the entire value chain of ore processing. Available methods for establishing a geometallurgical model are in many cases limited and not yet comprehensively validated. Some of the limitations include: sampling density, assaying methods and quality, forecast accuracy block model content, geostatistical solutions for non-additive components, blending and assessment of positive impact of geometallurgy on the project. Synthetic ore models combined with process simulations and production scheduling, based on strong case studies, present a viable way to address these shortcomings. Such synthetic ore models will have realistic elemental and mineral distribution, textural attributes and 3D variability for input into the design of an appropriate geometallurgical program.A synthetic orebody was created for an apatite-bearing iron deposit. Variability in modal mineralogy was described by geostatistical parameters combined by a set of linear and trigonometric functions. The generated synthetic deposit model was used to develop a mine production plan to generate a simulated process feed. The process feed had detailed information required for beneficiation process simulation: modal mineralogy, chemical composition of minerals, grain size and specific gravity. The synthetic system was used to measure benefits that a geometallurgical program developed for real cases could provide, compared to production where only head grade is optimised. These include a reliable sampling strategy and confidence in the feed-quality forecast for economic evaluation.CITATION:Lishchuk, V, Lund, C and Lamberg, P, 2016. Development of a Synthetic Ore Deposit Model for Geometallurgy, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 275–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By G Corder

Even though most major operating companies in the minerals industry have Board-level endorsed sustainability principles and objectives, design engineers typically have no mechanism that allows them to implement those objectives in their work. In addition, the existing project management systems do not readily deliver the innovative solutions needed to address key sustainability issues, such as those related to significantly reduced carbon emissions, minimal environmental impacts, and maintaining the societal ‘licence to operate’. SUSOP® (SUStainable OPerations) is an approach for the integration of sustainable development principles into the design of mineral processes, which has been developed through the Co-operative Research Centre for Sustainable Resource Processing (CSRP). Somewhat analogous to the well entrenched HAZOP (Hazard and Operability) studies, SUSOP® is a holistic, systematic and rigorous mechanism for identifying and assessing sustainability opportunities and risks at each stage of project development - from corporate planning, through design and operation, to decommissioning and rehabilitation – without compromising financial rigour. SUSOP® was developed, tested and enhanced through its application to real case studies in the minerals industry. This development path provided significant insights into the process of identifying and evaluating opportunities for improving an operation’s contribution to sustainability and its long-term business case.This paper will discuss the need for a methodical approach for integrating sustainability principles into mineral processing plant design, present the key elements of SUSOP®, and outline its development path through real case studies. In addition, the reasons why such an approach will have growing importance into the future will be raised.

Aug 8, 2011

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997