Search Documents

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

By J Brisebois

The derelict Lake George Mine is located at Captains Flat in NSW, acommunity of approximately 450, which lies some 43 km southeast ofQueanbeyan. It straddles the Molonglo River, which flows toQueanbeyan and thence the nationÆs capital, Canberra. Catastrophictailings dam failures in 1939 and again in 1943 resulted in the transportand dispersion of thousands of tonnes of sulfidic wastes downstream,with terminal settling in Lake Burley Griffin, in Canberra. The mine wasclosed in 1962, and major rehabilitation in 1996 - 1997 addressed the riskof further collapses, and reduced water flow into the underground mine.Nevertheless, acid mine drainage from the mine, and seepages ofcontaminated water from the capped tailings dumps continue to pollutethe Molonglo River for some 30 km downstream.Environmentally, the highest contributor to the total contaminant loadof the river is the Main Adit Spring. This was shown to be a constantgroundwater-driven acidic flow, with contaminant generation resultingalmost entirely from the ingress of gaseous oxygen into the undergroundworkings. Long term remediation may be possible at source, by pumpingreducing gases into the sealed mine, but the probability of thistechnology succeeding to the required degree is yet to be demonstrated. For at least the medium term, treatment of contaminated water flow(s)will be required to achieve any of the water quality targets that may beapplicable to the river. Three methodologies were short listed, but anumber of strategic uncertainties remain, which the NSW Derelict MinesProgram will address. Future risk arising from long-term contaminantrelease by the treatment wastes must be considered. Appropriate data,and realistic long-term performance parameters regarding the relativestabilities of water treatment sludges are scarce, and make properevaluation of competing technologies problematic.

Jan 1, 2003

By Bof J, Lowe S

BHP's newest colliery on the Southern Coalfield Is Tower Colliery. It is situated near Wilton some 60 kms south west from Sydney. It commenced its operations in 1978 and since that time has experienced considerable roof problems. In its eight years of operations, production has been 936 687 tonnes to December 1985. To a certain extent this is a reflection of the ground control r,,b1cros present in the colliery. paper out Iines the signif mt g,, logical features that are known to exist in the colliery and their influence on roadway development. Faulting has hindered the mine's development and an igneous intrusion has had outhursting associated with it. The prevailing roof rock has also had an impact on the roadway conditions. The paper will look at intersection deformation in present workings. Extensometers have been installed in these areas and provide measurements to verify visual observations. The results show a significant increase in roof movement as the roadway is developed from a single heading, to a T-intersection and then Into a four-way intersection.

Jan 1, 1986

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974

By Jeffery RI, Pollard CA, Fear NJ

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

In the southern part of China, car-bonate rocks outcrop in large areas. Ka-rst develops owing to hot, humid climate and heavy rainfall. In deposits of coal, iron, bauxite, tungsten, tin and base metals exist karst formations within or near the mineralization zones. Three pro-blems should be solved in the mine cons-truction in karst region. The first is the drainage and safety control of karst groundwater. Different methods are used to cope with local hydrogeological con-ditions, e.g. drainage from surface by submersible pumps in wells penetrating groundwater seams; drainage from under-ground drifts which intercept groundwa-ter flow with clusters of holes drilled into karst aquifer or with vertical ho-les drilled from surface to the drift underground; cement grouting to block off channels or to seal a part of aqui-fer; groundwater pollution control; etc. With those measures many Chinese mines of tremendous waterflow were success-fully developed and valuable experiences were gained. The second problem is the stability of buildings deteriorated by surface subsidence due to drainage. The occurence and distribution of surface cavings by drainage were studied.

Jan 1, 1990

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Walton M. C

A combination of flotation and smelting technologies is proposed as a cost-effective means to maximise the revenue of base metal operations. The proposed treatment route breaks the grade - recovery nexus associated with the treatment of ores exhibiting difficult mineralogy in conventional plants. Aspects of the two technologies are reviewed and typical capital and operating costs presented. A significant improvement in revenue is demonstrated in a worked example, where a copper-lead-zinc operation is examined in terms of the conventional and proposed treatment options. For the selected ore, the net smelter return per tonne of mill feed improved 57 per cent, from US$89.70 to US$141.10 with the proposed treatment option. This represents an additional US$51.4 million in annual revenue. Metallurgical operating costs increased by US$20.12 per tonne of mill feed for an incremental capital requirement of US$30.3 million for an existing operation.

Jan 1, 1992

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993

By Maiman R

One method of forecasting prices of metals is based on analysis of historic relationships between prices, inventories and consumption. The first, but generally overlooked step in this analysis should be to remove from the inventory and consumption figures the effects of seasonal variations. The next step is to construct diagrams which show prices plotted against ratios of inventories to consumption. These diagrams indicate that, when inventories are high, prices show little response to changes in inventories. Below a critical level of inventories, however, the psychology of the market changes and small changes in inventories lead to large moves in prices. The critical level of inventories is termed the "pinch-point"; the diagram which shows prices in relation to ratios of inventories and consumption may be called a "pinch-point diagram".

Jan 1, 1990

By Gray N. B, Grimsey E. J

A steady state heat and mass balance simulation of the Western Mining Kalgoorlie Nickel Smelter (KNS) flowsheet was developed within the framework of the commercial software METSIM. The KNS simulation can achieve all plant setpoints through the adjustment of controlled process inputs, and provides a useful tool for the evaluation of the current flowsheet and potential flowsheet developments The simulation model and a number of applications are discussed in this paper.

Jan 1, 1991

Computers represent substantial capital investment. A better return on that invest- ment comes from more effective use of the computer's facilities. By using Telecom's data communications facilities, more people in more locations can have ready access to those facilities.

Jan 1, 1983

By Tarvainen M, Mattila O

Outokumpu Oy has systematically developed the automation of mineral flotation covering the technology of both new devices and control methods, and as a practical result of this effort currently produces two on-stream X-ray analyzers. The Courier 300 system basing on conven- tional X-ray technology is applied to complex or large processes. The newer Minexan 202 dis- tributed probe system based on radioisotope technology is developed mainly for simple or small scale applications. In this paper aspects and experiences of these analyzer systems and their applications for flotation control are discussed with particular reference to the role of the computer

Jan 1, 1977

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

Filter Presses are used in a wide range of process industries where high quality filtration at elevated pressure is required. This is mainly due to the fact that modern presses are fitted with polypropylene filter plates which combine excellent corrosion resistance with high mechanical strength. Filtration pressures of 15 Bar at ambient temperatures are common ensuring low residual moisture content and easily manageable filter cakes. Recessed polypropylene chamber plates have been in use for the last 15-20 years and have replaced plates and frames almost entirely. The latest development in plate technology is the polypropylene membrane plate. These provide lower moisture content cakes at significantly higher capacity than recessed chamber plates. Because of their stayboss-free construction, membrane plates provide excellent cake washing facilities which make them suitable for a wide range of process applications. Membrane plates are available both as fixed and exchangeable membrane types. Overhung membranes can be fitted to existing plates manufactured in cast iron or plastic to enhance the performance of existing presses.

Jan 1, 1989

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

By Corbett GJ, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 in strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995