Search Documents

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultra- mafic complexes related to two orogenic episodes which took place during Paleozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe- Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

The population and the per capila consumption of mineral resources have both grown dramatically during the century past. It is argued that growth will continue through the century ahead but that the magnitudes of undiscovered resources are probably adequate to meet demands. The challenge that the mineral explorer of the future will face is finding deposits beneath several kilometres of barren rock.It is further argued that the principal challenge that society will face in the century ahead is the amelioration of environmental stress.

Jan 1, 1993

By DiStefano AB, Dale SG

This paper describes the laboratory study implemented to investigate the application of the subaerial technique to tailings disposal for the proposed Olympic Dam Mine. The results of the study and the resulting design parameters are presented. The subaerial technique of tailings disposal is described and the advantages of the method for disposal in arid climates highlighted.

Jan 1, 1984

By Myers PA, Noble MR, Lawrence JS, Cannings WR

The Perseverance orebody presents the Agnew Mine with a wide variety of geological settings, necessitating the application of several mining methods within the limited strike length being extracted.Mining methods have been introduced and modified during the six years' production history of the property and that evolutionary process remains very active.The methods used, in use or planned, are:Hand held scraper cut and fill Hand held mechanical cut and fill Post pillar cut and fillOpen Stoping (uphole benching) Modified vertical crater retreat Sub-level caving

Jan 1, 1985

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

Discontinuities often have a very detrimental effect on the stability of mine highwall faces. The west wall of the Muja open cut is remarkable for the number and variety of discontinuity sets which occur over a relatively small area. To-date 14 separate structural domains have been identified over an area measuring approximately 560 m by 120 m.The structural domains have been grouped into four structural assemblages on the basis of their angular relationships to each other and to regional folding and faulting. The distribution of these structural assemblages appears to be erratic and no controlling factors have been identified to explain or predict them other than in the most generalised terms.

Jan 1, 1993

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

By Nevolina VG, Zakharova IB

The results of a study on the flotation of baddeleyite and associate minerals are presented, together with effective flotation reagents. Detailed microcrystallomorphological analysis of the benefication products were made to find out the features of distribution of different baddeleyite generations between froth and chamber products. To reveal the dynamics of interaction of technological properties of minerals with their morphology and constitution, a method of onthogenetic analysis was used. It is well known that the difference between technological properties of the particles of the same mineral depend greatly on its genesis, but also the relation is direct - by means of constitution (habit). Thus, flotation behaviour of minerals depends on morphology microinclusions, distribution of impurities, dislocations and physical properties of individual particles. The microrelief of baddeleyite grains and crystals from froth and chamber products was studied with an electron scanning microscope. Chemical composition was determined by means of laser, microprobe and chemical analyses. The difference between baddeleyite generations, their distribution in benefication products, and the effects of grain sizes, number of inclusions and chemical compositions were valuated. Conclusions on baddeleyite flotation properties were made. Mineralogical study on eudialite grains from rough ore and eudialite concentrate was carried out. The interrelation between eudialite and associate minerals and negative effect of aegirine on technological properties of eudialite were revealed as well.

Jan 1, 1993

By Young DJ

Gold mineralisation at the Hamata prospect is related to a series of stacked pyrite and quartz-pyrite veins associated with a number of shears which strike N to NE and dip E. Mineralisation is contained entirely within the Morobe Granodiorite close to the intersection of the Upper Watut Fault and some younger NE to SW striking faults. The prospect was originally detected in 1987 by a regional stream sediment sampling programme. Subsequent mapping and sampling outlined an anomalous zone approximately 900m long by 300m wide. Drill testing has indicated a resource of 46Mt at 0.9 g/t Au.

Jan 1, 1991

Japanese pig iron production in 1973 registered about 90 million tons. As clearly seen from the productivity (2.04 t/m3/D), and fuel ratio (494 kg/t-pig), the Japanese steel industry has maintained quite high levels of efficiency in blast-furnace (BF) operations. Among the many factors which have contributed toward these high levels of efficiency, the use of high quality coke is very important. The Japanese steel industry imports about 85% of its metallurgical coals from various countries of the world, including Australia. The effective use of these metallurgical coals of various origins in accordance with their re- spective properties is most essential for maintaining coke quality. This paper describes coking properties of various metallurgical coals and blending techniques based on these coking properties, in relation to the specifications of coke quality required for efficient BF operations. This paper also describes briefly new technology for expanding the scope of the use of coking coals.

Jan 1, 1975

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

By Xu C

This paper describes the structure and operation of an interacth.. computer program for mineral industry financial analysis and production planning. It includes comprehensive risk analysis with correlated variables and optimal production scheduling using Lane's balancing cut-off grades and the general dynamic programming approach.

Jan 1, 1995

By Sen A. K

The Chiria Iron Ore deposit falls within the well-known Horse-shoe-shaped Singhbhum-Bonai-Keonjhar belt in India, where most of the deposits supplying ore to various steel works of Steel Authority of India Limited (SAIL) and Tata Iron and Steel Company (TISCO) are located. With an estimated reserve of about 2000 million tonnes of ore (at 55 per cent Fe cut-off) spread over four contiguous blocks, it is the largest iron ore deposit in India and one of the largest in world. The present study is confined to only one of the four blocks of Chiria viz North Block, comprising an area of 2.11 km2. `Corporate Plan 2005' of SAIL envisages development of a large open cast mine at Chiria to meet its enhanced requirement of iron ore by 2001-02 AD.

Jan 1, 1995