Search Documents

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

Secondary steelmaking (or ladle metallurgy) has been developed as a post- steelmaking ladle treatment to produce steel of superior quality. Its rapid growth has resulted from quality improvements, productivity increase, operational flexibility and process route economics. Advances in secondary steelmaking are very impressive during the past decade, and many commercial systems have been developed for performing one or more of the following unit operations: degassing, atmosphere regulation, reheating, refining with synthetic slag, rinsing gas treatment, injection of solid materials and alloying. The metallurgical requirements imposed by the current competitive steel market include more precise analysis tolerances, minimum level of detrimental elements, improved cleanness, demanding service performance and better processability. In most cases, these requirements could only be realized by the application of appropriate secondary refining facilities. Continuing developments in simplicity of design, cost advantage, quick cycle time, improvements in peripheral services such as refractories, instrumentation and in-situ analysis, extensive exploration of new applications, and the use of computer, can be expected. An exciting future is predicted for the widespread adoption of secondary steelmaking to perform most of the major refining functions over a variety of steel quality. It will also become a vital link in the total steelmaking process for production of tonnage steel at the large integrated steelworks and the mini-steelmills.

Jan 1, 1986

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

By Enga B. E

Following considerable laboratory studies concerning diesel particulate control systems for underground use, a Canadian program was initiated to implement practical, real-life systems. This program covers the application in seven mines throughout Canada, of a particulate control system, to 14 engine models from four engine manufacturers in 18 different vehicle types, for a total of 23 vehicles. Partially funded by the Canadian National Research Council (NRC), this program required detailed analysis of operating cycles, maintenance variabilities and installation problems. This paper summarizes the work carried out to date to define real-world targets and the success achieved so far in attaining practical underground particulate control.

Jan 1, 1988

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984

By Hatcher MI

Exploration undertaken at Copley diapir has located several occurrences of oxidized supergene and primary sulphide copper mineralization at the margin of the diapir or in adjacent country rocks. The mineraliza- tion is related to carbonate-rich epigenetic solutions which moved along major structural features closely associated with the intru sive diapir.

Jan 1, 1975

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By R Lovel, P Fung, J Manuel, M OÆCo

The iron blast furnace is the most widely used and efficient producer of liquid iron. The integrated steel works is however under environmental pressure largely due to emissions from sintering and coking. The combustion of coke breeze during sintering contributes to greenhouse gases (eg carbon dioxide) and is the source of much of the emissions of SOx and NOx. Coke breeze, the fines produced during coking of coal, is also suffering supply issues as coke demand increases while coking capacity is constrained by environmental concerns.CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide can be sequestered into growing biomass prior to combustion. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource. Samples of pine wood flour, sawdust and red gum wood char were characterised and used in small-scale granulation and sintering tests. Red gum char granulated as well as coke and could be used to make acceptable sinter. Large-scale sinter pot test were conducted with char to produce sufficient sinter for ISO quality tests and calculate sintering performance parameters. Results showed that coke could be completely substituted by red gum char during sintering without loss of quality and with actual improvements in sintering performance. Furthermore, gas analyses made during sintering showed that there were significant reductions in SOx and NOx when char was substituted for coke. It is anticipated that the results reported here, although preliminary, will stimulate an increased effort into further research on the use of char in iron ore sintering.

Jan 1, 2004

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

Nickel laterite approximately 40% of the remainder caning deposits. ores are the source of the world's nickel with from sulphide ore Although laterite ores are near the surface and cheap to mine they require significantly more energy to treat than sulphide ores. The escalation of oil prices comiencing in 1973 meant that nickel laterite refineries using oil as an energy source were placed at distinct disadvantage relative to sulphide refineries or those with coal derived energy. The Queensland Nickel refinery commenced a construction programme; in 1980 to allow ore drying and power generation to be converted from oil to coal. Since late 1981 ore drying has been undertaken using heated air from two moving grate spreader grate stokers. The changeover from oil to coal drying proceeded without process disruptions. This paper discusses the plant changes required to allow the receipt of coal and the operating performance obtained from the coal fired air heaters.

Jan 1, 1987

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

The ownership, policies, organisation, structure, market, financial considerations and communications of a large resource project vary significantly through its discovery, feasibility, development and production phases. The extent of these changes, from discovery in 1957 through to 1979, is examined for the Mt. Newman iron ore project in the Pilbara region of Western Australia and some of the factors that influenced it are detailed. This shows that only some of the influences are under the control of the mine owner/operator, despite their significant impact on the returns for the massive capital invested. The effect of the general business climate on the various phases is also examined.

Jan 1, 1980

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

Western Mining Corporation (W.M.C.) operates a nickel refinery at Kwinana, 30 km south of Perth. The refinery commenced pro- duction in May 1970, with a rated capacity of 15 000 tpa of nickel metal. A hydrometallurgical route was chosen as the most expedient way to produce nickel metal at a time when world demand for nickel was outstripping the supply. Later events dictated that an increase in production from the refinery be achieved. To this end, matte produced from Kalgoorlie Nickel Smelter, which was commissioned in 1972, was used in varying proportions as a complement to the concentrate initially utilised as input to the refinery. The effect of matte addition was to increase the capacity to 30 000 tonnes of nickel per annum. This was accompanied by other benefits which were 1. reduction in energy consumption per unit of nickel produced, 2. improved metal extraction, 3. improved precious metal recovery, 4. reduced production of ammonium sulphate by-product. Refinery operating results for the years 1970 to 1983 show how matte feed has improved refinery performance in these areas.

Jan 1, 1984

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

By Moon N. T, Torrance A. C

This study has considered the effect of mechanical shock on the resilience of the glass microspheres commonly used to sensitize an explosive emulsion. The damage to the glass microspheres caused by detonating cord, emulsion manufacture and the manufacture of the glass microspheres were considered along with the effect of sensitizer concentration on explosive performance. Reductions of up to 50% in the glass microsphere concentration of an emulsion explosive can result from poor initiation practice, such as the use of high strength detonating cord as downlines during initiation. Laboratory results suggest that detonating cords of strength greater than 3.5 g/metre should not be used as this can seriously affect explosive performance, particularly in small diameter charges. This reduced performance results from damage to the sensitizer elements and recrystallization of part of the emulsion phase.

Jan 1, 1990