Search Documents

By Das A. K

Investigations were carried out to understand the effect of liquid viscosity (u = 1 x 10-3 - 5 x 10-' Ns/m2) on the size of primary bubbles formed at high gas injection rates (Q = 100 - 1000 cc/s, U = 0.04 - 0.42 mach) under room temperature conditions using flush tuyere (3 mm diameter) operating vertically upward. Tuyere pressure fluctuations were correlated to the mode of bubble formation by simultaneously filming the bubble and the corresponding tuyere pressure fluctuations displayed on an oscilloscope screen. A simple mathematical treatment is presented to estimate bubble size in viscous liquids. The theoretical results are compared with the experimental measurements.

Jan 1, 1987

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

To discuss this relationship both the problems of the mechanisms of ore accumulation and the origin and cause of volcanism must be faced. Volcanic activity is associated with hydrothermal activity but the causes of volcanism are inseparable from the problems of the origin of magmas generally. To be more in accord with the inevitable reaction between water and silicates at high temperature, it is suggested that reconsidera- tion be given to the role of water in magmas such that our general concept of magmas becomes one of hot hydrous pastes rather than melts with water in them. It is claimed that a general concept of magmas as gelatinous hydrosilicate masses is a far better assumption because the rheological and diffusive properties of such materials enables an adequate explanation of a greater number of observations. It is consistent with the mergence of magmatic and metamorphic rocks and requires low to modest temperatures at the time of liquifaction allowing convergence with mobilised and disturbed sediment masses. The physical and chemical properties of both wet sediment pastes and magmas envisaged as hydrolised silicate masses are entirely dependent on the enormous internal surfaces of their disordered solvated components. Mechanical disturbance, such as reliquifaction

Jan 1, 1974

By Hellsten K, Eshuys E

The best long-term approach to exploration involves the use of extensive quality data and the integration of many different factors, methods and techniques. The successful exploration manager needs to integrate people, area selection and exploration methods, with the use of descriptive and genetic geological models. Based on a syn-metamorphic genetic model for Archaean gold, successful exploration in Western Australia requires the integration of data on anomalous gold, alteration, lithology and structure. Many other parameters such as geophysics, geochemistry and regolith studies provide additional, indirect information that needs to be integrated into the overall exploration programme. Timely access to research findings and ability to integrate these into immediate exploration has contributed considerably to the success of the gold industry in Western Australia since 1980. Extensive and deeper drilling, and the ability of computers to handle the volume of data generated have enabled effective testing of many more geological targets.

Jan 1, 1996

The common notion that the Box Hole Bore mineralization represents a variant of the Mississippi Valley type, has not been supported by the present investigation. Most of the common characteristics of Mississippi Valley type, namely 1. saturated saline brines; 2. low temperature domain; 3. mineralization in intraformational breccias and collapsed anticlinal structures; 4. hydrocarbon-rich or foetid carbonates, and 5. very simple geochemistry seem not to be applicable. The Box Hole Bore mineralization features: 1. moderately saline brines (18% NaCl); 2. very high temperature (495¦-520¦C) and low density brines, of critical vapour:water ratio and low pressure of formation (700 bars); 3. mineralization confined by faults and ex- tending laterally into carbonates of high pore volume such as stromatolitic dolo- mites; 4. ore environment characterized by oxidizing conditions, such as ferruginous carbonate and silica sands of high energy environment (heavy mineral banding) and 5. more complex geochemistry than is normal for Mississippi Valley type deposits (copper sulphosalts, and appreciable silver content). Additionally, the ore has un- usual textures formed by the replacement of carbonates and barite by large idiomorphic galena crystals. The pressure and temperature domains of the Box Hole Bore mineralization indicate post- Devonian emplacement and local high heat flow, possibly related to the Alice Springs Orogeny. Because of high lead and zinc trace element con- tents (100-600 ppm) of the carbonates, even out- side mineralized areas, it is possible that the mineralizing fluids have derived their metal con- tent from a local source, possibly aided by evap- oritic concentrations of the tidal to supratidal sequences. The new model for Box Hole Bore gives treater importance to the confining faults.

Jan 1, 1984

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991

By Fengyan D

Removing the interference of latter events, the data of geophysical (such as gravity and aeromagnetic) anomalies may indicate whether the mobile belt exist and whether the adjacent terrains of the mobile belt originally belong to one single unit. The petrotectonic assemblage can provide informations about the tectonic setting where it was generated from. The structural style can exhibit the kinetic and kinematic processes. The form of ancient isogeotherm may reflect the ancient geothermal regime which is related to the tectonic mechanism. In general, the early Precambrian terrains suffered polymetamorphism and multiple structural deformation. The researches must be carried out for the distribution of paleogeotharm and m.tamo'phic facies and zones on the basis of recovering the early structural style with structural analysis method; then a relatively correct conclusion may be geined on the ancient geothermal regime. This method can be known as "Ancient Thermotectonic Analysis". Through the sythetical research, a real knowlege about the tectonic setting of early Precambrian mobile belt can be obtained.

Jan 1, 1990

By Noakes MJ, Willsteed TV

In the past few years an elevated gold price has resulted in the evaluation of many small scale surface gold deposits in Australia typically containing about 2-3 g/t Au. Operators have tended to assume that at the lower end of the grade spectrum only heap leaching is economically possible whereas above some assumed "cut-off" grade, carbon-in-pulp or similar techniques can be considered to have economic advantages.Studies made on a number of these prospects has indicated that this rather arbitary choice of treatment method can be mis-leading.A case study has been prepared assuming a "typical" situation and is presented. The deposit contains three million tonnes of ore assaying 3 g/t Au and is amenable to open pit mining methods. The mine site is remote but accessable and existing infrastructure is minimal. There are no unusual environmental constraints.

Jan 1, 1984

AXTAT is a computerised system developed by the Western Australian Department of Minerals and Energy in conjunction with the local mining industry for recording and retrieving information about fatalities and work related injuries. Since its inception, the system has gained considerable recognition by consistently demonstrating its usefulness as a tool, not only to the Department, but for the entire industry nationwide. AXTAT has played an important role in the continuous improvement process in management of occupational health and safety in the Western Australian mining industry with gains in both human and financial terms, by regularly providing timely and accurate statistical feedback on fatalities and lost time injuries to industry.

Jan 1, 1996

By Hashimoto H, Arai Y, Sikong L

For utilization of solid carbonaceous materials produced in processes of cracking heavy oil, such as petroleum pitch, as powder fuel, it is necessary to develop a process for fine grinding of these materials. It is known that grinding' additives are effective for fine grinding of cohesive and heat-sensitive materials such as petroleum pitch, therefore in this study, effective methods for fine grinding of petroleum pitch with some grinding additives were investigated. Experiments were carried out by using comminution kinetics based on mass balance. From the results of the investigation by using a batch ball mill, it was found that sodium stearate, calcium stearate and carbon black were effective additives for the improvement of grinding efficiency. Optimum concentration of the grinding additives was also found to give a required particle size of products. Concerning to the action mechanism of these additives, it is considered that the additives which adhired to, or were absorbed on the surface of petroleum pitch particles not only prevented cohesion of the particles but improved dispersion of the particles as well. From the results of the investigation by using a laboratory screen mill which is a representative built-in classifiered impact crusher, carbon black was found to be an effective additive for the improvement of grinding efficiency and mill performance. It is also considered that the improvement of classification efficiency by carbon black affected the mill performance.

Jan 1, 1987

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By W Boughton, L Gilbert

The Australian Water Balance Model (AWBM) has found widespread use in Australia in estimating the streamflow behaviour of catchments. It has been used at the Ridgeway Gold Mine, in central west New South Wales, to estimate streamflows in creeks potentially affected by loss of spring-fed baseflow due to mine dewatering. The AWBM estimates are used to assess the effect of mining on streamflows and the need to provide compensatory flow releases, which would be drawn from mine water supplies, into the creeks, in compliance with regulatory consent requirements. The monitored flows in some of the creeks exhibit non-typical behaviour, with streamflows increasing in autumn months despite a lack of significant rainfall. This behaviour is believed to be due to the combined effects of discharge from rock fractures and the effects of evapotranspiration in the riparian zone. A modified version of the AWBM has been developed which much more closely simulates the observed flow behaviour and which will be used in ongoing flow assessments for the mine. This paper outlines the difficulties involved in modelling low flows in small catchments that are subject to a number of influences (other than mining), describes the development of a refined model to improve simulation of low flows and baseflow in small headwater catchments and highlights the need for good baseline data to calibrate such models.

Jan 1, 2006

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

Small mines exist because of a restricted deposit or a small market. With the right management at the present time the small mine can have lower total costs than larger mines. Charbon is an example of a small mine with a restricted deposit and a specialised product. The development which incorporates a unique rail loading facility and flexible coal preparation plant was achieved with a modest capital outlay and in record time. To remain competitive in future with large scale mines who seek increased production the small mine must achieve increased productivity through automation, higher speed equipment and a multiskilled workforce. Deregulation of the industry, scrapping the Coal Industry Tribunal and the Joint Coal Board would benefit small mines greatly. Management of a small operation also requires multiskills which need to be supported by outside help in the form of consultants and temporary staff. In the 21st century small mines will continue to provide a service to the market.

Jan 1, 1988

Lower Silesia Coal Basin/SW Poland/ is adjacent to highly gas saturated igneous massiv and since the beginning of this century more than 1500 outbursts have occurred in four existing mines, including 1295 in the most hazardous mine Nowa Ruda. Prevailing part of these are carbon dioxide/coal outbursts of ejected masses 50-5000 tonnes/av.200/t and gas volume released from 200 m3 to 800,000 m3 Magnitude of these phenomena is growing with the depth and for present extraction levels/ 375-753 m/ may be expressed by a formula: M = 4.25/H-400/, where M-masses ejected, t and H - depth of extraction, m. Regulations obligatory hitherto call for gas pressure measurements to be made in 3 m long and 42 mm dia. boreholes spaces not more than 25 m along the longwall face and taking sample of drillings for desorption testing. Criteria of a hazard are following: pressure higher than 30 kPa /for C02/ or 80 kPa /for CH4/ and desorption more than 1,44 cm3/g. These criteria are not satisfactory because many outbursts occurred in spite of low values of parameters measured and for several times no hazard was evident after very high values were obtained. Moreover, observations show that a huge majority of case outbursts occurred in coal weakened by local geological distortion.

Jan 1, 1980

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

Manganese ore has been mined from the Peak Hill Gold- field since 1948 and from the Pi'lbaraòGoldfield since 1954, and it is probable that some deposits- In and, near the Phillips River Goldfield will be mined at a future date', There are also several million tons of mariganiferous ;naterial which is too low in manganese. .co.ntent_ for . present requirements. The manganese deposits¦of Western Australia are mostly superficial. They hav' been formed during the Cainozoic Era by supergene enrichment ò6f Precambbrian: manganiferoius sediments, and by deposition from -solution on, or'in caves in, the Cain- ozoic land surface. The manganese in solution was derived from the weathering of Precambrian manganifer.ous s.edimexsts, None of the deposits are of hydrothermal origin, nor are they related to igneous rocks in any war, other than as ultimate source rocks. There is ho evidence-'t.o.:sugge,st that meta- morphism has been responsible for.the emplacement of any deposit. The tenor of the ore varies'aec'ording'to the quantity of gangue in the orebody and- also to the nature of the part- icular ore minerals. The main ore.mine.rals are the oxides pyrolusite and cryptomelane and the 'o'xide-silicate braunite. The main gangue minerals are hematite, limonite and quartz. The deposits of high grade oreò(-above.45 per cent Mn) range in size from 50 tons to many thousands of tons but most of them are in the 500-5,000-tons r .nge .

Jan 1, 1964

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993