Search Documents

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

Developments in mining technology are outlined which point out that longwall face technology has the capacity to produce 20,000t/d on a regular basis. The optimum length of longwall faces is about 250m. Developments of headings and gate roadwyas require radical changes to meet longwall developments. New conceptual models are outlined to meet the challenge.

Jan 1, 1988

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By M Coulthard, J Rivalland, K Dugan

Prior to 2001 Yallourn Mine has pumped approximately 1000 Megalitres of water per annum from aquifers beneath the mine floor in order to control aquifer pressures that were thought to have an influence on mine floor and permanent batter stability. In 2001 one of the deep aquifer pumps was shut down for five months in order to measure the aquifer recoveries. Prior to the shutdown a UDEC model was created in order to predict what level of recovery in the aquifer pressures would be critical to mine stability. The shutdown showed that the aquifer levels recovered and stabilised at levels that did not threaten the stability of the mine. The aquifers recovered to levels below the critical levels identified in the UDEC model.

Jan 1, 2003

By Williams J. D

Magnetite has been used in coal processing for many years and it is likely that its use will continue well into the twenty first Century. While magnetite is only a minor cost component in coal processing, the use of processed magnetite in dense medium separation is essential to provide the split of quality coal products which the markets of today demand. The occurrence of magnetite in Australia is relatively abundant, but a combination of its iron content, magnetic properties, quality and proximity to the coal processing plants is essential to provide a low cost product for use in the Coal Industry. The demand for more splitting of coal in coal processing may require more grades of magnetite, particularly as a finer grade lower specific gravity medium to separate the finer quality low ash coals.

Jan 1, 1991

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

This paper discusses how the i-kon TM Digital Energy Control System may be deployed by miners of massive underground orebodies to deliver significant advantage in terms of safety, cost and environmental compliance. Digital Energy Control offers an exciting opportunity for mine operators to review their blasting and mining practice to gain the most advantage from this new technology.

Jan 1, 2000

By Orid A

A fast, non-contact technique for measuring sizes of rock fragments on a conveyor belt is presented. An image processing technique called active stereopsis is used which makes use of a light stripe projected on to the surface of the fragments on the conveyor belt. A CCD TV camera is used to capture the shape of the distorted light stripe. the video image of this shape is then processed by a computer program so that the 3D profile of the surface can be obtained by triangulation. The sizes of the rock fragments are then calculated from this profile. The speed of the technique is improved by calibrating the light stripe system before measurement begins so that the profile of the fragment surface can then be measured using simple geometry. The technique is fast and highly parallel so that it is able to operate in real time.

Jan 1, 1990

The number and severity of sulphide dust explosions in underground metalliferous mines have increased in recent years, despite various methods used to prevent or inhibit them. A dust explosion occurs when a cloud of combust- ible dust in an oxidizing atmosphere is exposed to an ignition source with sufficient energy to ignite the dust. A computer blast simulator model was used to investigate the movement of the fractured rock, temperatures and volumes of the explosion gases in a 70 m high, 24 m wide open stope.

Jan 1, 1988

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

Optimisation of capital in the development process is critical to the profitability of any new mining venture. The process of optimisation should apply to all aspects, that is the financing, management, revenue, reporting and, of course, the development of the project. Unfortunately, too much emphasis has been placed on the optimisation of the financing or reporting aspects and too little on the project itself. This paper addresses the latter.

Jan 1, 1991

The accurate calculation of ore reserves is one of the most important functions under- taken at a potential or operating mine. In recent years there has been a trend towards recommending more and more complex techniques for the calculation of reserves. However these are not always necessary and many improvements could be made by the use of all potential data and a heavier geological input. An ore reserve should be the result of geological not mathe- matical or engineering reasoning. All ore reserve estimates are wrong and the important thing is to.recognise why they-are wrong and to take action to minimize the errors. Geostatistics and other complex mathematical techniques may appear to answer all our needs for ore reserve accuracy but there are many drawbacks, not least of which is the communi- cation gap which may develop between the operator and both management and production Personnel.

Jan 1, 1979

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By R Ashworth, S J. Hall

During trials which began in May 2005, traditional steel dump bodies for transporting iron ore on 220-tonne haul trucks at a Labrador iron ore mine were compared to a novel rubber suspended dump body. Loads were measured and compared over some 93 700 loads, representing more than 20 Mt transported. Maintenance costs and downtime were also measured over the course of the trial, which lasted nearly one year. This paper outlines the parameters and results of the trials. Parameters measured included payload and production improvements, carry-back reduction, downtime due to body maintenance, and wear on the floor of the suspended dump body. These parameters were then compared to those for conventional steel dump bodies in use at the mine, and conclusions were drawn. The resulting comparisons were significantly positive in favour of the new suspended dump bodies, confirming that each truck could haul an additional 41 000 tonnes per year, that downtime hours could be considerably reduced, and that body availability and service life can be extended through use of the suspended dump body. There was also a high level of operator acceptance of the suspended dump bodies due to less loading shock and a smoother ride.

Jan 1, 2007

Commencing early in 1975, Saraji Mine in Central Queensland will product 3.56 million tonnes in the first year and then 4.57 million tonnes annually for the Japanese and European markets. The coal will be mined from a series of pits separated by corridors which will be mined at a later date. Through the corridors flow regional drainage structures and power lines. Relatively easy areas will be mined initially to assist the cash flow and to minimise start-up difficulties. For ease of scheduling it is desirable that pit lengths exceed 3 000m but this will not always be possible. Ramps were designed using 1 200m spacing and 5 per cent gradient as optimum but modified to suit specific conditions. One ramp will be in the end of each pit nearest the ROM hopper and stripping will commence from this end. The advantages so gained are shorter haul distances, immediate access to the coal after stripping and simplification of the excavation of the first ramp. Haul road location was defined by the minimum present value of construction plus operating costs. Road design utilised airfield construction charts because wheel loads were outside the range of available road design manuals. Low load resistance characteristics of

Jan 1, 1974

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002