Search Documents

By K Paki, K Parker, J F. Dupont

The Mount Charlotte grinding circuit at KCGMÆs Fimiston mill was recently equipped with three 650 mm CAVEX cyclones in order to improve the overflow P80, reduce the fines bypass to the underflow and improve the underflow density/recovery of water to the overflow. After the first two sets of surveys were conducted air core boosters (ACBs) were installed on the 650 mm CAVEX cyclones in an attempt to further increase their performance. JKTech was approached to assist with the examination of the data obtained from the surveys; this data was intensively modelled to determine, to a high degree of confidence, the impact the changes to the cyclones had on the classification and the benefits to the plant. This paper outlines the outcomes of the trial and the methods used to determine those outcomes.

Jan 1, 2007

By Paine G

Kidston Gold Mines commenced mining in 1984 and currently mine approximately 10 million tonnes per annum of ore and waste using a conventional truck and shovel open pit method. The overall mine grade is a low 1.82 grams per tonne.The mineralisation is generally uniform within the ore zones and mining boundaries are staked out from blasthole assays according to pre-determined cut-off grades. Buffer blasting is necessary to minimise post-blast lateral movement of in-situ grade for digging control.The characteristics of the rock currently mined vary widely from soft oxidised to hard unweathered rocks. Blasting problems have been experienced during the initial mining phase in these harder rocks.

Jan 1, 1986

By Manzoori AR

From a detailed combustion testing program and earlier experience with Leigh Creek coal, the Electricity Trust of South Australia (ETSA) gained a wide insight into the use of low rank coal fired boiler plant. This work is fundamental for the selection of boiler design parameters and other details which in turn determine the correct coal deposit selection for future power station development. In addition it gives boiler designers a good indication of the measures required to give reliable plant operation. Extrapolation from experience with existing plant, the designers main source of information, was not considered appropriate because of the lack of experience with similar coals. Brown coal beneficiation is also being assessed by ETSA in an attempt to improve the coal quality by the pretreatment of the raw coal prior to combustion in future coal.fired boilers. ETSA is also involved in the development of circulating fluid bed and gasification processes to determine whether these alternative processes are a more viable method of utilising the South Australian coals than pulverised fuel firing.

Jan 1, 1987

By Thomas R

The successful `marriage' between a company seeking to raise funds to develop a project and their financiers calls for a strong mutual understanding of each other's needs. For a company attempting to raise funding, the alternative methods are ever expanding. The optimum method will vary depending on the financial position, risk/reward outlook of the company and the strength of the project for which development capital is being sought. It is likely that small mining companies will need to raise equity funds for advancing projects to the development stage. At that time, they will probably still require a reasonable level of shareholder equity to meet the requirements of banks and other parties to cover potential cost over-runs on the project and feasibility costs. Larger companies, however, are likely to find it much easier and cheaper to raise debt from banks. When evaluating companies and projects for funding, banks will pay particular attention to the quality and experience of management in developing similar projects and it may be necessary for some companies to retain the services of outside consultants. Before a project needs funding, companies should meet with potential financiers to develop relationships to select and ensure a smooth transaction to funding in the future.

Jan 1, 1997

Chemicals derived from petroleum raw materials satisfy so much of our industrial needs today that it is good to pause and realise two things -ò the petroleum chemical industry is so new, and the use of chemicals is a very old one.Petroleum is such an'abundant and convenient source of raw material that in little more than 30 years it has become the major source of supplyfor chemical rdanuf ctiree This paperw~l'l 'disc'uss t1.e main 'r`easons' for this rapid development by considering the : sub jest -under tkzree headings ea. Source of Raw Materials.b. The Impact of Petroleum Chemicals on Plant Design and Processes. ce Scme of the Major Chemicals Used Today.

Jan 1, 1962

By Harrison J

The correct selection of equipment to use in a mine is a problem which constantly faces the mining engineer. In some cases a wide choice of equipment with different operating characteristics is available. If this equipment is to be used to assist in moving the ore it may be possible to build a computer simulation model to predict how it will perform. Typical problems that lend themselves to this type of analysis are presented. The computer models are constructed using a recent form of the GPSS computer language, namely GPSS/PC for the personal computer. This language allows the programmer to construct models in a very short time and at a low cost. Of great importance is the easy way in which it is possible to change the models to answer any of the "what if?" questions the engineer may pose.

Jan 1, 1987

The introduction of legal certification of mine managers is a matter of history. It was introduced as part of legislation for mine safety. It has been said that such legislat- ion was written in blood. Like all legislation this legislation is divided into three sections; commands, obligations and sanctions. While legislation in all States on this subject is similar, the differences are great enough to have prompted the preparation of a Uniform Code by the Annual Conference of Chief Inspectors of Mines. This Uniform Code has not been adopted fully by any State to date. Legal certification of mine managers has made managers more aware of the requirements of the legislation covering their industry, legislation that reads as a summary on past accidents and methods of preventing them. While budding managers spend considerable' time in their early years in the preparation for certification, history has shown that the industry has benefited from their efforts. A better knowledge of the safety acts by the managers has produced safer operations, and a higher standard of management has raised the technical standards of mining operations to a stage where Australia can be proud.

Jan 1, 1980

By C Gourdon

The present study concerns a new type of mixer-settler unit where coalescence is promoted by means of the phase inversion method (MSPI). Using two different systems (alkaline etching solution û LIX 54 in kerosene and acidic aqueous solution û LIX 984 in kerosene) the influence of the total flowrate, the A/O phase ratio and the hydrodynamic conditions in the nozzles of the scattering device on the extraction and separation efficiencies are studied. Two modes of operation are clearly outlined and a theoretical model predicting the separation efficiency is proposed and compared to experimental results. A comparison between mixer-settlers with classic decanters and the MSPI unit has demonstrated the advantages of the latter where throughputs in the range 20 -25 m3.m-2h-1 can be easily realised.

Jan 1, 2000

Most mineral products exported from Australia to Japan, with the notable exception of coal, are purchased with weight and quality determined on discharge. Sampling of imported minerals for purpose of payment is done at facilities owned and operated by the purchaser. The selling shipper is represented at the weighing, sampling and testing by an independent inspection group who supervises the whole procedure. Sampling and testing are done within the provisions of the contract between the two parties, and normally in accordance with the relevant Japanese Industrial Standards (JIS). These JIS specify such things as the number and mass of increments to be taken; the practice of taking these increments; the method of determination of moisture, size distribution and quality. The JIS concerned with sampling however, are meant to be basic guides rather than rigid rules. Hence sampling and testing practice varies from plant to plant. In general Japanese sampling facilities and methods are elaborate and efficient. Opportunity is given for the discussion of varying technical viewpoints between consumer and shipper. However the resolution of differences and the implementation of changes normally takes a long time. Such discussions seem best reduced by prior contract agreement on reasonable specifications and detailed testing methods. The independent inspectors

Jan 1, 1976

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

By Hart J. G, Anderson J. S

The presence of platinum metals in the nickeliferous copper ore of the Thomson River Copper Mine near Walhalla, Victoria, was first revealed in 1905 by assays made in the laboratory of the Department of Mines (1).These disclosed the presence in the ore of 5 dwt. platinum metals, 1 dwt. gold and 13 dwt. silver per ton. Attempts to isolate the platinum-bearing mineral were unsuccessful, and the absence of obvious native platinum led the assayer, Mr. P. G. W. Bayley, to suspect that the platinum might be present as sperrylite. Subsequently, Mr. C. M. Lyons, then metallurgist to the Long Tunnel Gold Mining Company, Walhalla, tried to isolate the platinum mineral from samples of ore containing as much as 7 dwt. platinum metals, but again without success.In 1912, a sample of copper matte from this ore was submitted to Messrs. Johnson, Matthey and Company, Limited of London, for analysis. The analysis, which is quoted below by their courtesy, revealed tnat a large proportion of the metal pi'eviously reported as platinum was palladium, there being about two parts of palladium in the matte to one part of platinum.

Jan 1, 1942

By Braham B

The Australian mining industry isstill labouring under the impression. created by the Fitzgerald Report that it does not pay suffic- ient tax. This would appear to be the raison d'etre of the resource rent tax debate. The authors quantitatively compare the cash flows to the mine and government resulting from a large strip coal mine in central Queensland under a number of Australian and international taxation policies. The Liberal government policies are found to be internationally competitive while the Labor 1975 policy is excessively punitive. The present value of the returns to the public from the Liberal 1977 policy vary between three and six times the net present value to the mine, which belies the necessity for the imposition of a super tax. The levelling of a special royalty, excess rail freight, by Queensland could severely re- strict the development of new mines in the Bowen Basin. The impact of excessive freight rates is analysed on a combined strip-deep mine typical of the new projects nearing development in the region. Otherwise economic mines can be made marginal or even sub economic by this tax. Even with moderate rail freights, the mining tax laws of New South Wales are more favourable to the industry than are Queensland's.

Jan 1, 1978

The relevance of borehole and bore core evaluation to the design of underground coal mines is illustrated by considering the technical parameters of colliery design and the information from which they are constructed. The nature of this information is described, together with some methods for its storage, processing and presentation. Geophysical exploration techniques are compared as information sources. It is concluded that borehole and bore core evaluation is relevant and necessary for colliery design, but that optimum results will be obtained if drilling can be combined with geophysical techniques. Because of the inherent uncertainties in prediction of mining conditions the necessity of obtaining as much information as practicable from drilling evaluation is also stressed.

Jan 1, 1977

Mineral exploration conducted over a wide area of the State during the period 1960 to 1973 has resulted in the discovery of a number of significant deposits. Base metals, particularly copper, have been of prime interest while, more recently, the search for uranium and coal have assumed import- ance. Expenditure of $27.6 million by companies during the period under re- view has located 580,000 tonnes of cop- per, 370,000 tonnes of zinc, 350,000 tonnes of lead, 24 million Kg of uran- ium oxide and 2,500 million tonnes of coal. A variety of other metals and non metallic and industrial minerals have been investigated in a diversity of geological environments.

Jan 1, 1975

This paper deals with a few aspects of town planning and town management which affect human relationships within that town. Its scope is limited to the consideration of towns forming an adjunct to a mining operation, and particularly considers these aspects at the Hamersley Iron Pty. Limited, town of Parabur doo, Western Australia. Planning and standards of a new town and amenities are-discussed and related through living comfort to an effect on human relation- ships. Town administration and the promotion of many forms of social activities are dealt with in detail to illustrate the importance of quickly forming a cohesive community from a large number of newly arriving individuals. The results achieved by the planning and administration at Paraburdoo are highlighted by involving many residents by way of answers to a questionnaire.

Jan 1, 1973

The following is an outline of the main metallurgical process developments which have occurred at Port Pirie during more than 100 years of smelting. Emphasis is placed on those process developments which evolved from research and development at Port Pirie, rather than those based upon purchased or established technology and straightforward plant engineering. Most processes involved have undergone major change and improvement through the efforts of Port Pirie staff. A culture of metallurgical research and development evolved strongly during the years when G K Williams made such a great impact, and continued for half a century. This culture involved strong links with external research bodies, particularly universities. A near complete bibliography of these developments is provided, together with a listing of patents. Research and development by The Broken Hill Associated Smelters Pty Ltd commenced in 1918 at South Melbourne, and after transfer to Port Pirie in 1921, continued there until 1989. Three periods of highly successful innovation resulted ù that of G K Williams into the 1930s, the post-war period until about 1962 and the period with developments led by Denby H Ward from about 1970 to 1985.

Jan 1, 2000

By S Corbel, P J. T Donchak, W Gorczyk

The Hodgkinson Province numerical modelling project aims to develop an improved understanding of the physical conditions that lead to the localisation of goldbearing fluids within known systems and apply this understanding to the prediction of potential new sites of gold mineralisation. The project follows a series of stages from identifying the key parameters required to construct and test simulations through to reverse engineering of known deposits and ultimately applying the conditions identified in the preliminary stages to predictive simulations. Results of the modelling demonstrate strong geometric controls of the localisation of fluids during mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

By Sehic OA

One aim of testwork and flowsheet development is to ultimately provide a reliable and flexible plant that is simple to operate and maintain. Testwork can indicate amenability of ores to CIP treatment and provide a basis for process design and economic appraisal. Batch cyanidation and CIP tests are often sufficient for small projects. Continuous multistage test rigs can be operated to simulate plant operation and to provide data for flowsheet optimisation. Operating requirements, gold recoveries and potential problem areas can be anticipated at an early stage with more confidence. Subsequent project development involving decisions on the basic flowsheet, equipment types and general plant arrangements are based on practical considerations and experience. Computer aided process modeling and economic appraisal can be useful in analysing various tradeoffs, firming up the flowsheet and equipment sizes, and in specifying operating targets for the future CIP plant. INTRODUCTION Carbon-in-pulp (CIP) technology which has developed rapidly since 1974 is now accepted as an economically and technically viable process for the efficient recovery of gold. This paper describes testwork and flowsheet development procedures used for CIP evaluation and design.

Jan 1, 1982