Search Documents

By Todd W, Stone C

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

By Moorrees C

Carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite yields a magnesium bicarbonate leachate with a substantial soluble iron concentration. The iron concentration depends upon the leaching conditions (particularly time, temperature and pulp density) but is generally in the range 0.005-0.5 g/litre. If this soluble iron is not removed prior to the precipitation of the magnesium as a hydrated carbonate, then this product will be contaminated by the iron, and will not yield a final product (high-purity magnesia) that meets specifications.The soluble iron content of the magnesium bicarbonate leachate can be reduced to an acceptable level by addition of solid aluminium sulphate either during carbonic acid, leaching of the crude calcine or to the clarified leachate. Chemical analysis and X-ray diffraction revealed that the iron is precipitated as an iron-containing hydrotalcite-type compound, [Mg6(Al,Fe)2(OH)16]CO3.4H2O. The actual composition of the precipitate depends on the amount of aluminium sulphate added and the precipitation technique used. Because precipitation of iron in this manner also results in reduced magnesium recovery from the leachates, It WIll be necessary to develop methods for recovering the magnesium component of the precipitates.

Jan 1, 1984

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

By S C. Goel

The Obuasi Mine in Ghana, West Africa is the largest producing gold mine in Africa, outside South Africa. The mine has changed from a mine producing from narrow vein, high grade quartz orebodies to a mine producing from wide, lower grade sulphide rebodies. Traditionally mining methods were cut and fill and sublevel caving. Now the preferred stoping methodologyis long hole open stoping. Transverse or longitudinal methods are both used, dependent on the orebody characteristics. The change has been technically, socially, economically and politicallychallenging and at times has tested the abilities of those responsible for the operation of the mine. However, the benefits have been many. Safety has improved significantly, ounces from underground have doubled. Productivityhas doubled and underground unit costs have reduced bya third. These achievements have allowed the Obuasi mine to staycompetiti ve in this time of falling gold price. During 1999 and 2000 a full review of the mining and processing operations was undertaken, and as a result, the mine is now in a phase of restructure. Efforts are being made across the mine to improve efficiencies and to reduce costs. The future for the Obuasi Mine is an exciting one.

Jan 1, 2000

THE following description of the surface plant of the Great Fitzroy Mines is to be understood as having been compiled by a mechanical engineer, who concerns himself more with the various appliances used, their correct construction to enable them to accomplish their prescribed work, and the production and transmission of the power required to operate them, than with the reasons for the physical and chemical processes which those appliances are called upon to assist in carrying out. Hence the metallurgist will not find herein more than the skeleton of the organism, which perhaps he would wish to be clothed with the detailed description of the substances undergoing treatment, in their various combinations, at all stages, and the results attained in separating the valuable constituents from the worthless. So, also, no details will be found of the methods employed by the management for. the purpose of determining by sampling and assaying the nature of the various products obtained.GENERALThe ore being worked at the Great Fitzroy Mine is divided into two classes :-1. Ore that requires concentration before smelting.2. Ore that can be smelted direct.Flow-sheet (Fig. 1) shows in outline the process of treatment to which ore of the first class is subjected, and the writer will endeavour to fill in that outline with some details of the appliances used.

Jan 1, 1911

Until 1937, the mining of ore was carried out by conventional methods, using pneumatic drills and standard drill steel. The adoption of the diamond drill, formerly used for exploration work, for blast hole drilling in stopes, was first developed by Noranda Mines Limited, Noranda, Quebec, although it had been used previously in Northern Ontario and Western United States, to remove weak pillars and ore remnants left by conventional methods. Previous to the adoption of the diamond drill method at Noranda, a sub-level benching system of stoping was used. Sub-levels were driven at 35 ft. intervals and the benches drilled off by pneumatic drills using sectional steel. Results were very satisfactory, in sulphide ore, where the drilling was comparatively easy, but in the harder rhyolitestopes the footage drilled per machine-shift was only half of that obtained in the sulphide stopes, and owing to the high gauge loss, there was often difficulty in drilling holes to the required depth. This led to trials with the diamond drill for this type of work. While the cost per foot was more than with sectional steel, an appreciable saving in development work could be made by increasing the sublevel interval from 35 ft. to 60 ft., and stope widths from 60 to 100 ft. This saving, together with the increase in blasting efficiency, resulted in a substantial reduction in overall costs.CONDITIONS FOR SUCCESSFUL APPLICATIONWhile long diamond drill blast-hole mining has widespread application, there are certain conditions which appear to be desirable, if not absolutely necessary, for its successful use.

Jan 1, 1946

By Hohnen CA, Limerick JM, Hall DRT

An uniquely-designed flash furnace for smelting of nickel concentrate and for the recovering of metal values from the slag generated has been in successful use for nearly six years. Within the last eighteen months the ability of the furnace to treat slag arising from converting operations without significant reduction in capacity has also been successfully demonstrated. Previously, converter slag had been treated separately in an electric furnace. The salient features of smelter developments are outlined and slag chemistry is discussed. The low cost method for the introduction of coal to partially replace light fuel oil is reviewed and total energy requirements evaluated.

Jan 1, 1984

By Reynolds JO

This contribution by. The Australasian Institute of Mining and Metallurgy has three main thrusts. First, an Institute (and industry) view on academia and the need for more entrepreneurship at top academic levels, second the need to lift our technological game, and third, professionalism and the perceived role of mineral industry education. While I will deal with each of these separately they are of course inter- related and can be brought together under the frequently used, but insufficiently practised title, "communications". First then, The Institute and industry view of academia. There are some academics in the audience and I imagine they may wish to reply to my remarks with an academic view of industry. That is not unreasonable. Like all human institutions, academic institutions vary in quality and characteristics. Some are successful and some less so. Some historically are well renowned. Others that were once successful schools have declined. Lesser known schools have grown into prominence. What is it that sets apart 'good' highly regarded schools from those that are not so well regarded? It comes down to one main ingredient - "leadership". The strong mining schools in the past 100 years have been strong because they have had outstanding and clearly identified leaders. Strong clearly identified leadership has always had rapport with, and the support of the industry. The two go hand- in-hand, each nourishing and supporting the Other.

Jan 1, 1986

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003

The Copper Concentrator at Mount Isa Mines Limited treats approximately 6 Mt of chalcopyrite ore annually. The ore is currently sourced from the 1100 and 3000 orebodies at Mount Isa. Chalcopyrite is the only significant copper bearing mineral, with pyrite, quartz and dolomite being major gangue minerals. Ore is typically 10% chalcopyrite, 11% iron sulphides and 79% non-sulphide gangue. Copper ore is treated through two autogenous mills, two ball mills and a flotation circuit. The autogenous mills replaced a crushing plant, two rod mills and two primary ball mills during 1991. For routine analysis of concentrator performance, composite samples of mill feed, final concentrate and tailings are generated every 4 week period. All samples are sized and size fractions are assayed. Recovery of mineral species to the concentrate are then calculated for each size fraction. Sometimes liberation analysis was also performed by QEM*SEM (Quantitative Evaluation of Material by Scanning Electron Microscope).

Jan 1, 1990

By P Knights, M S. Kizil

Truck/shovel operations constitute 50 - 60 per cent of the cost of open pit mining operations. Mining companies, therefore, are constantly seeking to close the gap between actual truck/shovel productive capacity and maximum potential truck/shovel capacity. This paper analyses the performance of a mixed truck/shovel fleet in an open cut coal mine in Australia. It analyses operating delays, and proposes a novel graphical means of determining truck-limited or shovel-limited operations. A goal seeking algorithm is advanced in order to maximise truck/shovel match factors (MF) and hence optimise fleet productivity.

Sep 26, 2011

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988

By Carlie JC

Many low sulphidation epizonal gold and zinc-lead vein deposits within magmatic arcs are situated on basement highs, and post-date both the main volcanic episode and porphyry copper (gold) mineralization. These features are best explained by emplacement of a flat batholith a few kilometres beneath each mineral district, as recently demonstrated by geophysical data in the Baia Mare district of Romania. The batholith provides heat for the hydrothermal system, and results in extensional faulting both through up-doming of the overlying rocks, and in some arcs through incipient collapse of the thermally weakened crust under regional extensional stress. More water-rich magmas emplaced at greater depths could explain some deep epizonal and mesothermal gold deposits situated outside magmatic arcs.

Jan 1, 1995

By Winter W, Steele DA, Trudu AG, Gray CM

The Luzon arc extends for about 900 km from Taiwan to the island of Mindoro (central Philippines); in this area late Tertiary to Recent volcanism is considered to be the result of eastward subduction along the Manila Trench. The arc is composed of five segments, all of which have individual characteristics with respect to tectonic setting and magma chemistry (Defant et al., 1989). From the north to the south these are (Fig. 1): (1) the eastern Coast Ranges of Taiwan and the islands Lan-Hsu and Lu-Tao (Taiwan Segment), (2) the islands off the north coast of Luzon (Babuyan Segment), (3) the Northern Luzon Segment, (4) the Bataan Segment, and (5) the Mindoro Segment. Defant et al. (1988) suggest that the Bataan and Mindoro segments of the arc, both of which are characterized by different isotopic compositions and levels of large ion lithophile element (LILE) enrichment in the lavas, are separated by a 'pull-apart' zone, the Macolod Corridor.We are currently studying the mineralogy and petrochemistry of Late-Miocene to Pliocene volcanism in the Northern Luzon Segment (NLS), which comprises the geographic area of the Cordillera Central. This area has so far received limited attention, inspite of its wealth of porphyry copper, skarn and epithermal gold deposits. In this contribution we report the first results of our study of igneous rocks from the Mankayan Mineral District (MMD) which is located in the centre of the arc segment under consideration.

Jan 1, 1990

By E Villaescusa

This paper summarises research work carried out at the Western Australian School of Mines on mine backfill properties in the last few years. The fill properties presented relate to cemented aggregate fill and cemented tailings fill. Emphasis of these studies has been placed on the composition of backfill materials including aggregate particle size distribution, cement dosage and influence of cement admixtures. The unique features of the backfill research carried out at WASM during the last few years are the accomplishment of a study into the properties of large cemented rockfill samples by triaxial testing and the investigation of the properties of fill material made from highly saline ground water prevailing in the Goldfields region of Western Australia. Exploring different cost-effective binding agents for mine backfill was also carried out at WASM. Special effort has been put on the development of fill materials compatible with hydraulic and paste fills. During the process, specific methods and procedures for laboratory testing of backfill material have been formalised. The on-going backfill research on sample scaling is summarised and the future direction of WASMÆs backfill research focus is outlined.

Jan 1, 2000

Modelling of Synergistic Effect of Cyanex 302 and D2EHPA in Zinc Solvent Extraction A comprehensive model is presented to predict the synergistic effect of D2EHPA and Cyanex 302 on co-extraction of zinc and manganese. The experimental results indicated that pH, temperature and the extractants ratio have strong effects on the extraction process. Correlations were proposed to predict the distribution coefficient of zinc and manganese between two phases at different conditions by multiple linear regression. The correlations were simplified by eliminating less important terms by analysis of variance. Optimum conditions (ie pH, temperature, extractants ratio and aqueous to oil phase volumetric ratio) for obtaining maximum separation of zinc from manganese at different zinc concentrations and number of extraction stages were determined. For finding the optimum condition genetic algorithm was used. Comparison the model estimations and the experimental data show that the presented model has good ability to predict the behaviours of zinc extraction system over Cyanex 302 and D2EHPA.

Sep 13, 2010

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By C McMahon, S G. Walters

Mineral maps of æintactÆ and large particle textures have been produced routinely from optical microscope images. Polished thin sections of large particles (1 - 3 mm) provide a balance between representative sampling and the preservation of primary rock textures. Optical microscopy is an efficient way to generate mineral maps suitable for geometallurgical applications. The automated optical mineral identification was carried out using a Leica DM6000¬ microscope with a high precision stage suitable for direct tiling of image frames and good registration of multiple image layers. Standard images collected were 10 x 10 frames (20 mm x 16 mm). Four image layers were recorded: ætransmitted light plane polarisedÆ, ætransmitted light crossed polarsÆ, ætransmitted light crossed polars with 1l tint plateÆ and æreflected lightÆ. All image analysis was carried out using Definiens Professional V5¬. The four image bands were read directly in 12 greyscale bands. A segmentation algorithm produced objects based on homogeneity across all bands. These objects were then classified using a complex set of rules (Process Tree) that are based on image brightness in all 12 bands. Opaque and non-opaque minerals were classified in the same sample. Using this protocol up to 12 minerals can be satisfactorily classified in one sample. The opaque minerals were recognised using colour ratio and reflectance intensity in the reflected light image. Non-opaque minerals are more difficult because of the complex variable colours of many minerals and the complexity of interference colours. However, object-oriented classification using three transmitted light image layers and multiple rules is a powerful technique for recognition of these minerals.

Jan 1, 2008

Australia is the dominant iron ore supplier to the Asian market, a position that began to emerge with the development of the Pilbara in the 1960s. Iron ore is now one of AustraliaÆs main commodity exports and is likely to remain so well into the future. The annual price negotiations are the focus of widespread comment and speculation by financial analysts, journalists and mining professionals. Much is written on the subject, but how much is understood? What is the process all about and what can mine managers learn from understanding the pricing mechanism? Every one of the major regional iron ore markets has its own characteristics. The focus here is Australian supply specifically to Asia, far and away the biggest and fastest-growing of these regional markets. The core of the paper reviews and explains the key elements and procedures that contribute to pricing iron ore in Asia, a market that has long been dominated by the Japanese steel mills (JSMs) and that is now feeling the full force generated by the rapid industrialisation of China. First, however, it is important to understand how this market has evolved over the past 40 years, and the key relationships that have shaped and continue to shape the iron ore price. A description of the essential technical and commercial factors follows. Each area is explained in some detail to provide an overall demonstration of the linkages and the importance of understanding the various influences on the pricing process.

Jan 1, 2006