Search Documents

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By D. C. Peck, James. R. S., Chubb. P. T.

"Abstract -The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered matie intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendritic­ pegmatitic matie pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and mag­ matie breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to lOOJo within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that af­ fected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd :Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Severa! factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic inter­ action with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion .The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Com­ plex, U.S.A.) in terrns of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economie concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginal­ type POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By P. Cleyle, K. McDermott, M. Hall, C. A. Harris

"This paper describes the implementation of an expert system for monitoring and control of the NO. 4 autogeneous mill and spiral circuits at Wabush Mines.This process control system incorporated the mill operating expertize of Wabush Mines operating personnel and was implemented to improve spiral iron recovery and mill productivity by:1. Continuously monitoring the mill power draw and ensuring that the mill feedrate is regulated to prevent damage to the mill motor, while simultaneously maintaining the feedrate at or as close as possible to the maximum feedrate determined by the process supervisor.2. Improving control over the spiral density and feed rate.3. Improving control over both tbe rougher and cleaner wash water.4. Reducing the frequency with which pumps are plugged.5. Allowing modifications to be made easily and quickly to test various operating strategies.This system was installed using COMDALE/C, a real-time Expert System for Process Control. It was readily accepted by the process operators and produces higher production performance in comparison to the other 5 parallel mill lines at a lower power draw."

Jan 1, 1992

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By F J. Kelly

A chemical process, based on laboratory investigations, is proposed for the production of high-purity niobium oxide from a pyrochlore-perovsk1te flotation concentrate produced from ore obtained at the Oka, Quebec property of Columbium Mining Products Limited. The method developed included the decomposition and dissolution of the flotation concentrate with hot, concentrated sulphuric acid. The dissolved niobium was purified and concentrated by a solvent extraction step, using methyl isobutyl ketone as the extractant. The niobium was recovered from the extractant with ammonium fluoride solution from which niobium oxide was precipitated with ammonia. Finally, the filtered and washed precipitate was calcined. Ninety-six per cent of the niobium was recovered in a product analysing 99.9 per cent Nzo.. The reagent cost was in the range of $1.00 to $1.25 per pound of niobium recovered. Introduction OVER the past few years, Columbium Mining Products Limited has been engaged in the development of a niobium-bearing mineral deposit in the vicinity of Oka, Quebec. One phase of this program resulted in a flotation process capable of producing concentrates containing up to 50 per cent Nb205? Flotation pilot-plant

Jan 1, 1965

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By E. LaRocque

Denison Mines Limited has been processing uranium ore in the Elliot Lake area for the past 20 years. As the original concept of uranium processing has been modified somewhat over this period, the present paper will describe the current recovery practices at the Denison mill from crushing through concentrate drying and packing . Special emphasis will be placed on the leaching, ion exchange and precipitation sections of the process, with consideration being given to the entire circuit. Descriptions will be given of equipment now being used and control strategies will be discussed.

Jan 1, 1979

By T. Beamish, I. Vasilev, T. Nikolov, E. Marinov, D. Kirilov, P. Barrios

In April 2005, Umicore Copper de-merged from Umicore Group and created a new independent Copper company called Cumerio. As a separate company, Cumerio is a major European copper smelter and refinery and a leading producer of copper products such as wire rod, billets, cakes and specialty rod with a total production capacity of copper products in excess of 500,000 tpy with production plants in Belgium, Italy and Bulgaria. The Pirdop Smelter is the only state-of the-art smelter in South East Europe and it makes Pirdop the natural hub for the copper industry in the region. In order to be competitive in the international market the main challenges facing Cumerio are to maintain its low cost structure and to achieve higher production volumes while reducing its impact to the environment and striving for continuous improvement of the production process. Cumerio's state-of-the-art smelting facility in Pirdop has recently increased the anode production capacity to 250,000 tpy by the installation of the third evaporative cooler on the converters section that allows operating with three-hot converters. In April 2007 a general shut-down for repair and modification on the Flash Smelting Furnace and Waste Heat Boiler is envisaged. At this time a revamp of one of the existing Sulphuric Acid Plants is planned, resulting in a further copper capacity increase to 275,000 tpy with modest Capex. In 2005 Cumerio received from the Bulgarian Ministry of Environment and Water the Complex Permit under the EU IPPC criteria. Accordingly an Environmental Compliance Program was defined targeting a large reduction in the secondary emissions. The system will be commissioned in May 2007. In order to better integrate the smelter and refinery in Pirdop and to respond to the growing demand for cathodes in the region, a new state-of-the-art Electrolytic Refinery with an installed capacity of 180,000 tpy will replace the existing refinery. The new refinery is expected to be fully operational as from early 2008. This paper describes the challenges and the projects.

Jan 1, 2007

By N. H. Grace

"IntroductionDURING the past half century, the economy of Western Canada was largely centred on agriculture. However, the impact of World War II has led to an acceleration in the development of a variety of natural resources so that, today, Western Canada is experiencing great industrial development. Consequently, the availability •of low-cost energy assumes prime importance. In the final analysis, industrial growth and expansion are intimately linked to the energy resources.Coal ReservesHas Western Canada adequate coal reserves to meet the present accelerating demand for power in the days that lie ahead? This question must be answered before detailed consideration can be given to the probable patterns •by which various energy sources in Western Canada may be expected to meet the expanding demand. Figure 1 indicates the extent and distribution of the Canadian coal reserves, the data having been prepared by Dr. B. R. MacKay for the Royal Commission on Coal in 1946 (1). The amount of readily recoverable coal is listed as one-half the quantities shown on the chart. It is interesting-to note that upwards of 90 per cent •of the Canadian coal reserves .are located in the three most westerly Canadian provinces. It has been estimated that the coal reserves, at the present rate of mining, would be adequate for about 3,000 years. Consequently, it may be concluded that the coal •reserves in Western Canada •are indeed adequate to meet tremendous energy demands for many centuries. When the oil and natural gas have been exhausted, the great coal reserves will still be available."

Jan 1, 1953

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

By A. S. Bayne

THIS paper will present a review of the mining operations of one of Canada's most lately established gold mining districts (1). The history of the Little Long Lac and Sturgeon River areas is interesting in view of the fact that, although they have long been the scene of a certain amount of mining activity, they remained little more than an uninhabited wilderness until 1933, since which time ten producing gold mines and mills have been established in permanent operation, eight of these having entered production since the beginning of 1937. As complete a background as possible will be given concerning the major influences having a bearing upon living and economic conditions in the mining communities. The object, here, is to show the diversity of problems which demand the attention of the operator starting up and operating a new mine in present times, and to indicate the ways in which these problems are successfully met in this district. A description of the power facilities and plant equipment will be followed by a summary of the problems encountered and methods applied in exploration and development. This is to aid in forming a background showing the circumstances which influence the mining methods and costs of the various operations. The paper will conclude with a description of the mining methods used and the costs of the operations, including summarized analyses of the stoping methods and mining conditions. The various phases of operation will be dealt with separately, in so far as this is possible, in order to present clearly the salient features. It is necessary, however, that the reader bear completely and constantly in mind the fact that in actual operations these phases arc, to a large extent, intimately related and greatly affect each other, as well as being, in turn, affected by other circumstances beyond the control of the operator. A few of these circumstances are: capital available during the development period and early stages of productive operation; strength of rock comprising the ore and its boundary walls; grade, size, shape, and location of ore-bodies; and many other natural items which must be carefully weighed in relation to the details of operation.

Jan 1, 1940

By Patrick Moore

In 1971 the government of British Columbia issued a permit for the Island Copper Mine to commence disposal of 33,000 tons per day of mine tailings into Rupert Inlet, a marine fjord on the northwest coast of Vancouver Island. There was considerable controversy surrounding the development, public hearings were held, and as a requirement of the permit the company was obliged to carry out a comprehensive environmental monitoring program. The results of this program provide a thorough assessment of the environmental impact of submarine tailings disposal over the 24-year life of the mine. Following closure in December, 1995, the monitoring program continued for three years to determine the extent of marine ecosystem recovery and re-colonization. It is apparent from the findings of the monitoring program that the mine tailings were dispersed more widely than was originally predicted. It is also clear that widespread heavy metal contamination has not materialized. In retrospect it appears that submarine tailings disposal has resulted in far less severe environmental impacts than if the alternative of land disposal had been adopted. This review highlights significant aspects of public policy decision-making, design of environmental monitoring programs, and questions of interpretation of monitoring program data.

May 1, 2002

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By Greg Yuriy

Over the past two decades, Vale Canada has used discrete-event simulation in a key role to support many underground mining studies. Traditionally, general purpose simulation software was developed for manufacturing and service applications. Not until recently have Mine Designers and Simulation Specialists been able to model the dynamics of underground mining scenarios without extensive manipulation of the inherent tools and entities contained within these simulation environments. This paper discusses Vale Canada?s past experiences with a variety of simulation software, describing model development methods and highlighting some of the lessons learned. The paper concludes with a review of recently considered software and provides a framework of desired attributes/functions for modeling mining scenarios.

Aug 1, 2013

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003