Search Documents

By Gary Raymond

The Similkameen Division of Newmont Mines Limited operates a low-grade open-pit copper mine in southern British Columbia. The copper mineralization is extremely erratic.As a result, over seven years of operation, ore control methods have evolved from standard flagging based on blast-hole assays, through an in-pit grab sampling system, to the present method of mining to computer-determined ore-waste boundaries based on geostatistics. These improved ore control methods have resulted in a gain of at least 25% on ore tonnage miffed, at the same grade as obtained using earlier techniques. At the same time, geostatistical ore reserve estimates are now within 7% of milled ore tonnage and grade on a yearly basis, whereas the original polygon ore reserves under-estimated mineable ore tonnage by 15% to 45% and over-estimated grade by about 20%. The author discusses why traditional ore estimation methods give poor results in erratically mineralized orebodies and describes the geostatistical approach to the problem.

Jan 1, 1979

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By Paul Armstrong

THE first discovery of lead and zinc ore on Calumet island was made in 1893 by John Lawn, who then staked a portion of the property now owned by Calumet Mines, Limited. His discovery was developed by James and Calvin Russell, who are said to have shipped a few tons of sorted ore, averaging 39 per cent zinc, 13 per cent lead, and 11 oz. silver per ton. In 1898, the property was being operated by the Grand Calumet Mining Company, who mined and shipped, for treatment in a Belgian smelter, 1,100 tons of ore averaging 32 per cent zinc, 9 per cent lead, and an unreported content of gold and silver. After some indecisive exploration by an American syndicate in 1907, the property lay idle until1910, when the Calumet Metals Company-later reorganized as the Calumet Zinc and Lead Company-re-commenced exploration. After sinking an 85-foot shaft-the McDonald shaft-and doing a few hundred feet of drifting and cross-cutting, this Company, in 1912, erected a 150-ton daily capacity gravity-concentration plant, in which some 800 tons of ore, mined from the McDonald shaft and Bowie pit, were milled. Owing to very disappointing mill recoveries, the property was shut clown and-after several years of idleness-in? 1916 the mill and mining plant were destroyed by fire and the Company went into bankruptcy. In 1918, an unknown operator shipped to an Omaha, Nebraska, smelter 22 tons of ore, probably sorted from the dumps of the Ste. Anne shaft and Galena pits, averaging 44 percent lead, and 0.26 oz. gold and 61 oz. silver per ton. The British Metals Corporation (Canada), Limited, in 1926, optioned the property. They unwatered the McDonald shaft and, after doing an additional 300 feet of cross-cutting and drifting on the 85-ft. level, estimated there were some 33,000 tons of ore between this level and the surface. Surface exploration, including trenching, on other showings on the property gave discouraging results and the option was dropped.

Jan 1, 1941

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill? has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill? technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill? has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills? are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill? in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By J. E. Nesset

Significant progress has been made over the past few years on characterizing and understanding the hydrodynamic properties of frothers and collectors and their effect on flotation performance. This new understanding of the relationship between chemistry and hydrodynamics has dramatic implications for how flotation circuits should be controlled and optimized. Previous work has shown that choosing a frother of the right 'strength' is critical to the optimization process, and the work and discussion presented here serve to strengthen the argument. In addition, we know that collector chemistry may also influence hydrodynamic properties and needs to be taken into consideration. To achieve the desired outcome, the overall system of reagents and operating parameters must be considered. This paper describes and discusses some of the findings from recent research on frother and collector chemistry effects (on hydrodynamics), and how this knowledge can be used to improve flotation performance. Examples from plant experience are discussed.

Jan 1, 2009

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By Neil Camarta

$6 Billion Dollar Education ?? Construction is like war ? you need a command and control organization ?? A strong Owner?s team is a must ?? Smaller is better ? break the project into bite size chunks ?? New technology is risky ? lots of construction and start-up risk ?? Safety can be successfully managed ?? Don?t expect contractors to ?work well together? ?? Never, ever let Mining Engineers run stuff than can catch fire

May 1, 2008

By Daniel Hodouin, Claude Bazin

"This paper examines the economic advantages of adapting the production grade and recovery targets of a flotation circuit as a function of metal prices. The study is periormed using a steady state simulator for a Cu-Zn differential flotation circuit operating under the following strategies of 1) Maintaining constant operating targets, 2) Maximizing individual circuit Net Smelter Return and 3) Maximizing the global Cu-Zn circuit efficiency. Results are compared to assess whether or not one of the strategies produces benefits significantly higher than the others. A discussion of the tools required to achieve such a kind of control completes the paper.Paper not Available at Time of Publication"

Jan 1, 1997

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By R. J. Munday

Although uranium deposits in northern Saskatchewan are clustered around the Athabasca basin, basement lithostructure determines their distribution. Basal Wollaston Group pelites are invariably graphitic and carry uraninite in felsic segregations and biotitic pegmatite. Where these intersect the Athabasca Formation, remobilized uranium concentrated as pitchblende. Uranium is also concentrated in silicified and hematized sandstone where the Athabasca Formation overlies post-orogenic faults. Presumably, pregnant solutions associated with the fault were stripped of their metals as they emerged into the contrasting physico-chemical environment of the sandstone basin. Both these types of mineralization correlate with a Grenvillian (-1,000 m.y.) heating event and associated diabase intrusions. However, the rich pitchblende veins at Uranium City appear to predate the Athabasca Formation, but display spatial correlation with the Martin Formation. They are tentatively associated with a syn- to post-D3 retrograde metamorphic event which thoroughly leached crystalline basement and generated uraniferous fluids which escaped, and precipitated metals, into fractures associated with faults that define the grabens in which the Martin Formation was deposited. Remobilization events allowed some of this uranium to move upward into fractures within Martin sediments.

Jan 1, 1979

By R. Melley, P. Wissner

The paper looks at the basic theory of tri-bological wear and the role played by the lubricant and its additives. It presents the argument that the “real cost of lubrication” is not the purchase price of the oil or grease, but rather the costs associated with not using the correct lubricant. A number of examples are presented, covering oils, greases and additives, in which a detailed evaluation of the application has shown that when all of the benefits of using the best lubricant/additive are evaluated, the savings achievable greatly surpass the incremental cost of the superior lubricant. One of the emerging classifications of costs in industry today are those associated with environmental protection. Two of the examples used describe the replacement of more conventional lubricants with environmentally acceptable products, compounded to compete in all aspects of serviceability, but which have the added bonus of being not only biodegradable but also of being of low toxicity.

Jan 1, 1997

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017