Search Documents

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson's Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson's Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this 'clay belt' the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

1.Assessment of methane content in coal. Given a naturally low methane content in 11 Coal Seam and the fact that the areas of the 11 Seam adjacent to the tunnelway were degassing for a very, very long time due to previous development and mining, it is conservatively estimated that the remaining in -situ methane is less than 0.5m3/tonne. 2. Continuous miner cutting rate based on the past practice. The best loading rate recorded at the past operations of Smoky River Coal was 45 seconds for a 8 tonnes shuttle car. Using these records, the maximum peak loading rate potential at the face is calculated at 0.178 tonnes per one second or 10.67 tonnes per one minute. 3. Methane release at the face. ?The actual face methane liberation, conservatively assumed at 40% of the total in situ content: 0.20 m3/tonne ?The peak cutting rate: 0.178 t/sec ?The maximum (peak) face methane release: 0.20*0.178 = 0.036 m3/sec

May 1, 2003

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By N. Geoffroy, E. Benguerel, G. P. Demopoulos

In the late 1990s, a chemical process to remove mercury and selenium from weak sulphuric acid solutions was patented and implemented in the CEZinc refinery in Valleyfield, Quebec. The CEZinc process comprises two stages. In the first one, sodium sulphide is added to the weak acid solution in order to precipitate the soluble mercury. The solution is then treated with sodium dithionite in order to reduce the selenium to elemental form. Because of recent changes in the composition of the industrial solution, a project to study the background chemical reactions was started. In this paper, a review of the background chemistry is presented on the basis of several eh-pH diagrams on one hand, while on the other experimental results are reported dealing with the reaction of selenium (IV) species with either dithionite, sulphide or a combination of the two. According to this work, elemental selenium enjoys a wide pH-eh range stability with selenium sulphide being metastable. Selenium (IV) in single metal synthetic solutions was found to be reduced - to elemental state - at ambient temperature down to ppb range with dithionite as long as the stoichiometric ratio (dithionite/selenium) was in excess of two and the pH < 1.7. Under these conditions the reaction was very fast reaching completion within one minute. Sodium sulphide proved equally effective in reducing selenium (this time as selenium sulphide) to ppb range from single metal solutions. However, in mixed Se-Hg solutions deviations from this "ideal" behaviour was observed resulting in higher levels of residual soluble selenium left in solution.

Jan 1, 2008

By A. G. Storey, J. B. W. Bailey

"The Noranda Process at the Horne Division ofNoranda Mines Limited now smelts approximately 350,000 short dry tons of concentrate a year, which is 40% of the total smelter throughput. Campaigns are averaging 200 days and refractory consumption is much lower than in the conventional smelter.In this paper, details ofrecent operation are given, together with updated projections for operation with higher levels of oxygen enrichment.IntroductionThe Noranda continuous smelting process has been in operation at Noranda, Quebec, for six years and in that time it has smelted a million and a half tons of concentrate. It is currently smelting 1,200 to 1,250 tons per day of concentrate on an instantaneous basis"" and it is handling approximately 40% of the Horne smelter throughput.This paper will describe the current operation of the process and the improvements that have been made since 1976, when the process was described by L.A. Mills et al.lSince early in 1975, a high-grade matte averaging 73% copper has been produced, which is then sent to the converter aisle for final treatment. All the information in this paper refers to the operation of the process in the matte mode .Early in 1978, Kennecott Copper Corporation started up their new smelter near Salt Lake City, Utah , which has three Noranda Process reactors operating with high oxygen enrichment of the tuyere air (2). These furnace s incorporate some design improvements, which will be described briefly."

Jan 1, 1980

By Jason J. Ballentine

This paper presents a case study of how an asset strategy and zero based budget was developed for an existing crushing plant that had been purchased from the contract service provider by an Australian Iron Ore miner. The goal was to directly align the strategies and budget to the business goals. This however was not a simple task due to poor historical records and a general lack of information. These challenges were overcome and the benefits of a documented maintenance strategy, a justifiable zero based budget and employee engagement were realized.

May 1, 2007

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By J. R. Giegerich

Purpose It is the purpose of this paper to describe the application of underground conveyor systems to the transportation of ore in the Sullivan mine of The Consolidated Mining and Smelting Company of "Canada, Limited, at Kimberley, British Columbia. General Applications Conveying has been recognized as a means of underground transportation for a great number of years but only during the past fifteen to twenty years has there been any extended application of the method to underground metal-mine operations. Coal miners became conveyor conscious before metal miners. Probably one reason for this is the fact that there are more flat coal seams than flat orebodies. A second reason is that coal is light and is a less abrasive material than most metallic ores. The vast improvements made in belt construction during the past few years, together with improvements in mechanical conveyor equipment, have gone a long way in making this form of transportation attractive to the metal miner. In new mines being opened today, or in major extensions to older mines, the possibilities of conveyor transportation should receive serious consideration. There may not be any widespread application of the belt conveyor as a replacement for the conventional hoisting and locomotive haulage. Where there is an application, tl1e saving in cost can be appreciable and many operating ad-vantages gained because of ease in operation.

Jan 1, 1951

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010