Search Documents

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By Funsho K. Ojebuoboh

With several “green” applications on the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulphide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter-blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure where by calcium and magnesium is used todebismuthise lead was developed. The present conduct of this 1936 process, the Kroll-Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1996

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By C. Overton, R. W. Nice

"With todays economic trials and tribulations we have all become deeply engaged in costs and cost cutting in our field of mineral processing. Grinding is one of the most expensive unit operations. The cost of grinding media is the most expensive item in grinding costs. Therefore, it is only reasonable to attack the cost-cutting area by trying to reduce the consumption of media. This introduces the field of autogenous or rock-on-rock grinding.Rock-on-rock grinding is not new to us. It has been known for many decades;The South Africans used pebble grinding in the '20's for gold.Mr. B. Crocker was prompted for the same reasons to introduce pebble grinding at Lakeshore Mines in Kirkland Lake during the last war.The Buffalo Anchorite used beach pebbles in grinding prior to the war.Autogenous and semi-autogenous grinding is used quite successfully in the iron ore field. Base metals have their examples in Australia at Caba, in Africa at Komato and in Sweden at Aitik.Recently three mills in British Columbia and one in Arizona started with autogenous mills in their circuits. One was originally conceived to utilize a modified autogenous grind with a crusher in the circuit. All except the same mill had contingency plans for converting to semi-autogenous. All four mills have since converted to the semi-autogenous mode. These are Island Copper, Lornex, and Similkameen in B.C. and Pima Mining in Arizona."

Jan 1, 1975

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By F. Habashi

"A short account will be presented on the extraction of rare earths from monazite sand, bastnasite ore, and phosphate rock of igneous origin. This includes mineral beneficiation, leaching methods, fractional crystallization [of historical interest], ion exchange, solvent extraction, precipitation from solution, and reduction to metals. INTRODUCTIONOriginally, the term rare earths was only used for the oxides, R2O3, which are similar to one other in their chemical and physical properties and are therefore difficult to separate. Within the rare earth group, the elements scandium, yttrium, and lanthanum differ in their atomic structure from the elements cerium to lutetium (the lanthanides, Ln). Scandium occupies a special position with respect to this classification and its other properties, and therefore does not belong to either of these groups. The rare earth elements always occur in nature in association with each other. The isolation of groups of rare earth elements or of individual elements requires costly separation and fractionation processes owing to the great similarity of the chemical and physical properties of their compounds, which explains why the history of their discovery has extended over such a long period.The word “rare”, when used to describe this group of elements, originates from the fact it was thought that these elements could only be isolated from very rare minerals. Considering their abundance in the Earth’s crust, the term rare is now inappropriate. These elements are lithophilic and are therefore concentrated in oxidic compounds such as carbonates, silicates, titano-tantalo-niobates, and phosphates.The abundance of the rare earth elements taken together is quite considerable. Cerium, the most common rare earth, is more abundant than cobalt. Yttrium is more abundant than lead, whereas Lu and Tm are as abundant as Sb, Hg, Bi, and Ag. For all practical purposes promethium does not occur in nature. It forms only in nuclear reactors."

Jan 1, 2012

By R. C. Becker

Welding is playing an important role in the manufacture of construction equipment as used in the mining industry. It provides design possibilities which are unique to this method of manufacture, and normally makes possible lighter weight but stronger products, which can be a definite advantage to a user. Welding is an industry that has experienced major developments over the past decade, all of which have improved our capability to make better welds and make them more economically. International Harvester Company has been introducing these newer welding methods into its manufacturing plants, particularly those producing construction equipment, just as fast as their value has been proven. This paper discusses how modern welding methods are contributing to the manufacture of strip mining equipment.

Jan 1, 1966

By A. E. Flynn

THERE is at the present time a revived interest in amalgamation, due to the number of mines starting up, usually on high-grade ore, and utilizing this relatively cheap and convenient means of recovering gold, more especially in their initial stages of production. The marked increased use of the amalgamation process has revealed a dearth of amalgamators and there is no doubt the art of amalgamation has stood still for a generation or two and is not readily applicable to the modern practice of milling gold ores. Mill operators of long experience are learning the art for the first time and are giving it intelligent study, and considerable testing and research work is now being undertaken Most millmen consider amalgamation a simple process, and so it is when we have a clean ore with coarse gold, specially when stamps are used for crushing. In treating Nova Scotia ores by stamps and amalgamation, recoveries of 95 to 97 per cent are common and easily obtained. So-called 'under-water feed' is almost universally used in Nova Scotia and is quite beneficial. The water is supplied through jets between the dies and below the die surface and maintains this space as a live trap which catches the gold particles before they are overground and spoilt for amalgamation. With this method, the portion of gold recovered in the battery is higher than usual and often amounts to 80 per cent of the total gold in the ore, the remaining 20 per cent being caught on the plate. As a continuous amalgamator, the simple plate cannot be excelled. Some of the modern devices having moving or covered and not very accessible plates, which cannot be readily inspected and dressed to keep them in condition, do not give the best results in service. An exception might be drawn in the case of amalgamation of very heavy ore or concentrate which would bank up unless the plate is carried at such a steep inclination as to weep mercury. Difficulties in stamp-mill amalgamation are encountered when acid water is used or when grease is present. Also, certain sulphides and graphitic and talcose ores give trouble, resulting in poor gold recovery and high mer-cury loss. The older literature on gold milling deals with the common troubles of this type and the old-time amalgamator was well able to take care of day-by-day difficulties. When the difficulties were unsurmountable, the ore was classed as 'refractory' and other processes were used.

Jan 1, 1939

By B. Surender Mohan

Mining lignite pollutes the environment and causes ecological damage if unattended. Being conscious of the importance of environmental resources for the well-being of the living system, the Neyveli Lignite Corporation (NLC) adopts the policy of environmental regeneration as the foundation on which productivity is built. NLC started investing on Eco Care and Environment Protection long ago and it continues. Early investment in environmental protection has resulted in steady growth of the Company along with a healthy environment. The future vision of NLC is to be in the vanguard among the contributors to the community, environment and the nation by developing and utilizing industrial and human resources to the optimum. Untiring efforts are being put in mines (NLC as a whole) to maintain and sustain the ecological balance arising due to continuous mining activity. NLC?s Environmental Management System is becoming a symbolic role model for many of the opencast mines in Southeast Asia. NLC has been bestowed with number of prestigious Environment and Sustainability awards in recognition of the mammoth contribution in maintaining a clean and green environment.

Aug 1, 2013

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector&apos;s problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924