Search Documents

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By Arthur Laing

"IT is indeed a pleasure to have the opportunity of addressing this group today. Not only does it give me the opportunity of meeting with representatives of what is considered by many to be the most dynamic segment of industry in Canada today, but it also allows me to talk about a subject of para-mount interest to myself, the development of the North, and to explain, if even only briefly, some of our beliefs and hopes in this regard.It is inconceivable that all lands north of the 60th parallel, representing 35 per cent of Canada's total land area, which we believe contain a great natural resource potential, will remain as an undeveloped portion of Canada. The re-sources are there, although the people and private industry are as yet not there in sufficient numbers.It has been estimated that in the west and north of Canada there are 1.6 million cubic miles of sedimentary rocks. Of this figure, 342,-000 are thought to lie in Alberta, 115,000 in British Columbia and about 1 million cubic miles are thought to lie in Canada's northern regions, the bulk in the Arctic Islands. On the basis of apparent volumes of sedimentary rock, we estimate that as much as 13 billion barrels of petroleum may lie beneath the permafrost of the North-west Territories, another 3 billion barrels in the Yukon Territory and 33 billion barrels in the Arctic Islands. This is, indeed, a rich and elusive prize, and one which must be sought with a view to fulfilling demands on the production of petroleum."

Jan 1, 1966

By Jun Xiao, Xiaodong Li, Chunming He, Daixiong Chen

"Benzohydroxamic acid with double dentate can react with copper to form cyclic hydroxyl oxime acid copper chelate, indicating a good selectivity for copper oxide minerals flotation, especially for malachite. The flotation results of the pure malachite mineral show a strong synergistic collecting effect between hydroximic acid and xanthate at a ratio of 3.5:1, achieving a malachite recovery of 95.5% when certain sodium sulphide is used as a sulphidizing agent in the optimal pH range. Thanks to the synergistic collecting effect, the flotation recovery of malachite of a real refractory ore flotation ,can reach over 92% under the optimum condition, a 12% higher than the recovery achieved with the conventional collectors. In industrial application, the flotation of the copper oxide minerals is improved , leading to a high efficiency utilization of copper oxide resources.INTRODUCTIONBeneficiation of copper oxide ore is one of the recognized challenges in mineral processing industry. Copper oxide ore is a vital component of copper resource in the world, which has abundant reserves. Majority of sulphide deposits has oxidized zone on the top, and some deposits are oxidized to become the large and medium-sized oxide deposits (Willam & Chavez, 2001). Most copper oxide ores have problems in processing such as high slime consumption, poor floatability, complex ore property and low flotation recovery, so it is of great significance in beneficiation of copper oxide ores to develop an efficient collector, especially for malachite (Fu & Gu, 1997; Wen, 2010; Riet, Kier & Elford, 1980). At present, sulphidization-xanthate flotation is the most important method for treating copper oxide ore. In recent years, due to the decreasing ore grade, the utilization of refractory copper oxide ore draws more and more attention (Zhou, 2003), except for sulphidization-xanthate method, chelating flotation method (Lu, 2009), chemical beneficiation method (Lenormed, Salman & Yoon, 1979), microwave radiation flotation method, hydrothermal sulphidization-flotation method (Mao, Wen & Fang, 2014) and ammonia leaching of sulphide precipitation-flotation method (Lekang, Stevik & Bomo, 2003) have occurred."

Jan 1, 2016

By Tuula Mäkinen, Lauri Pesonen, Peter Björklund, Jouni Pihlasalo, Mikko Korpi

Outotec Direct Blister Flash Smelting technology has proved to be an efficient and environmentally friendly way to treat copper concentrates from the Zambian Copperbelt at Konkola Copper Mines' (KCM) Nchanga smelter in Zambia. The modeling of slag chemistry and thermodynamics with MTDATA software played a central role in deciding the operation parameters for the smelter. Outotec FSF Online Process Advisor is used to calculate the process parameters and to give valuable information of the process state for the operating personnel. The pre-calculated slag liquidus graphs are also integrated to the Online Advisor.

Jan 1, 2011

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By D. Gaboury

Most hydrothermal gold deposits contain quartz with fluid inclusions that record composition and temperature of the mineralizing event. Quartz has strong chemical and mechanical resistances to weathering and abrasion. Hence, quartz fragments occurring on weathered surfaces or in till cover have the potential to be used for gold exploration as far as we know what is the signification of the volatile content of the fluid inclusions for gold mineralization. In this perspective, fluid inclusions were analyzed in pure quartz by solid-probe mass spectrometry from gold deposits hosted in the Archean Abitibi (Canada) and Paleoproterozoic Birimian (Western Africa) belts. This approach provides the relative abundance of volatiles from families of fluid inclusions decrepitating at specific temperatures (Td). Fluids in gold deposits are aqueous-dominated with CO2 and minor H2S in accordance with their fundamental role as gold-ligands (H2S) and for pH-buffering (CO2) of the gold-bisulfide solubility. However, there is no correlation between CO2 and H2S contents of fluid inclusions with the gold grade of the samples. This suggests that trapped fluids represent a marginal portion of the fluid history recorded by the veins. However, in barren quartz veins away from known mineralization CO2 or H2S are commonly absent. Wide ranges in H2O Td from 250 to 450°C and CO2-H2O Td offsets are common, indicating phase separation. The content of other volatiles seems to be more dependent on the geological setting. Helium content may suggest proximity to a crustal-rooted fault, a critical parameter for gold mineralization. Methane and especially C2H6 appear to be indicative of fluid buffering by organic-rich material such as graphitic-shale. These rocks may provide an important primary gold reservoir from sedimentary metal-rich pyrite. Nitrogen-bearing fluids may be related to a magmatic component but can also be derived from organic-rich sedimentary rocks. For gold exploration, quartz containing CO2- H2S-bearing fluid inclusions and having H2O-CO2-Td offsets within 250 - 450°C has strong vectoring potential.

Jan 1, 2011

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By W. E. Newton

THE following notes are offered primarily to show that industrial minerals or their products have a much more important place in the metallurgical industry than is perhaps generally realized, and with the hope also that some statement by the metallurgical consumer of the relative merits of various materials for particular requirements or services will l;>e of value to the industrial mineral producer. These notes are not in any way presented as complete. Also, some of the statements made may be debatable. The grouping adopted is as follows: (1) Refractories; (2) Fluxes; (3) Construction materials; and ( 4) Miscellaneous applications. Fuels are not dealt with in the present paper. REFRACTORIES GENERAL: Refractories are materials which will withstand high temperatures with-out melting or becoming markedly soft or pasty. While their primary function is to withstand heat, they are usually called upon to resist one or more of the following destructive influences: abrasion, pressure, corrosion by slags or fluxes, and rapid changes in temperature. Refractory materials may be conveniently divided into three classes: (1) Acid refractories-consisting of silica, or containing silica as their chief constituent. They combine more or less readily with metallic oxides, forming silicates, and are hence termed 'acid'. The most important of these are quartz, quartzite, siliceous sand, tripoli, Dinas rock, and ganister. Most fire-clays, although generally considered neutral sub-stances, contain relatively small amounts of free silica and are, to that extent, acid. (2) Neutral refractories-the term is merely relative in most cases, since, at high temperature, many of the refractories that are classed as neutral will react chemically with a strong base, functioning as a weak acid; or, conversely, with a strong acid, functioning as a weak base. Chrome and graphite are the most nearly neutral of all the commonly used refractory materials.

Jan 1, 1936

By Paul-Henri Girard

La Mine Agnico-Eagle division Laronde situé à Cadillac, est un producteur d?or, d?argent, de cuivre et de zinc. Cette propriété est situé dans les cantons Bousquet-Cadillac le long d?une des ceintures géologiques les plus productives au monde. La mine Laronde a débuté la production en octobre 1988 à un rythme de 1360 tonnes par jour. Ensuite, elle a augmenté son rythme de production successivement à 1800 TPJ en 1990, 3300 TPJ en janvier 2000 et 4500 TPJ en octobre 2000. Agnico-Eagle, fondé par feu Paul Penna, a toujours eu comme politique la participation des employés aux décisions de la compagnie pour le déveleppement de celle-ci. Cet écrit va permettre de mieux comprendre la façon dont la division fût développé.

May 1, 2001

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By D. Yuan, L. Yan, R. Kalanchey, M. J. Collins, I. M. Masters

Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project located in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Since the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The "lime boil" process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95 to 98%; silver extraction was up to 94%.

Jan 1, 2011

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011