Search Documents

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

By W. G. Worcester

Generally speaking, the term 'clay' appears to convey but little to the average layman other than of a sticky substance to be rigidly avoided when making a cross-country drive in the family ark- especially so if the chains have been left behind. On the other hand, the technical ceramic; engineer, though his chariot be bogged in the self-same mud-holes, will, more than likely, be planning on ways and means for the conversion of the troublesome gumbo into paving bricks over which all might ride with pleasure and security. However, to come to the point, the term 'clay' bears much the same relation to the ceramic world that the term 'ore' does to the metallurgical; in other words, as there are many kinds of ores, so also are there many kinds of clays, and it therefore becomes necessary to classify and sub-classify them previous to a discussion of their relative values and importance. Hence, a brief digression will be made from the main topic of this paper in order to enumerate and classify a number of the more important types of clays. By so doing, the relative position of Saskatchewan clays, later discussed, will be better understood.

Jan 1, 1929

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By Thom Sedun

No sector of the mining industry is more closely tied to local communities than aggregates. Noise, dust, traffic, visuals aesthetics and environmental impacts all fall under the purview of neighbours, local governments and nongovernment organizations. It is no surprise that aggregate operations may not be welcome neighbors in many communities. In British Columbia (BC), the regulatory environment for aggregate operations includes a local component of municipal bylaws and land use-planning in addition to the usual suite of federal and provincial statutes that apply to its sister mining sectors. Additionally, under common law aggregate extraction is not considered to be a land use subject to land use zoning, and some aggregate processing activities can be regulated by zoning. Often traversing multiple local government jurisdictions, aggregate producers find themselves negotiating not only local traffic, but also a mosaic of regulatory environments. There is an opportunity in this present situation to facilitate the application of current technology and practices in the mitigation of many community and environmental concerns associated with aggregate operations. Moving a bulk commodity is a volume-based business, and operators often don?t have time for matters that don?t directly or obviously affect the bottom line. Regulatory agencies often play multiple and complex roles with respect to their industry, not the least of which is the fiduciary role. Balancing how and when to assist an industry is often a difficult decision. For the aggregate industry in BC, the Ministry of Energy and Mines saw an opportunity to assist not only aggregate operators, but also regulatory agencies, local governments, and the general public. Through investing in the Aggregate Operators Best Management Practices Handbook (handbook) project, the Ministry of Energy and Mines (MEM) believes that it will realize a return of upheld community values, enhanced environmental protection, improved regulatory compliance, reduce disputes and a stronger provincial aggregate industry. It is the intent to publish the handbook electronically through the MEM website later this year.

May 1, 2002

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015

By W. Griffith

"While oxalic acid precipitation practices are commonly applied on purified rare earth elements (REEs) pregnant leaching solutions (PLS), few efforts have been reported using oxalic acid (OXA) to recover REEs directly from untreated PLS. High oxalic acid demand is the most significant issue in all these direct oxalic precipitation (DOP) practices. Preliminary research on DOP of REE from a dilute PLS originating from an acid bake followed by water leaching was conducted. At 75°C, the oxalic acid demand was between 12 and 18 times the stoichiometric requirement for complete REE precipitation. Conducting DOP at 25°C had superior REE recovery but the product purity and filterability declined. Between 75°C and 100°C, REE recovery increased with increasing temperature. When sodium hydroxide was used to adjust the pH during DOP, in the range of 0.5 to 1.5, higher pH benefited REE recovery. Using ammonium hydroxide in place of sodium hydroxide, the REE recovery was reduced by close to 5%. Sodium chloride addition to the PLS was also investigated and the results showed that at both 75°C and 25°C, the REE recovery was enhanced substantially. At 25°C, when the oxalic acid addition was controlled at 4.7 times the stoichiometric requirement, the overall REE recovery reached 95% with the addition of 240 g/L NaCl. Other reagents such as KCl, NH4Cl also showed significant enhanced REE recovery at the same oxalic acid addition. The addition of sodium sulphate appeared to largely enhance the precipitation of LREE but inhibited the formation of HREE oxalate. All results indicate the formation of rare earth double salts may play an important role in REE DOP sulphate media.INTRODUCTIONThe conventional routes for recovering rare earth elements (REEs) from a sulphuric acid pregnant leaching solution (PLS) involves an initial purification step for removal of iron, aluminium for example by precipitation through neutralization, followed by precipitation of REEs as hydroxide, oxalate or carbonate salts, or by bulk solvent extraction for REE recovery (Xia, 2013). Another route was used by Bayan Obo in their historical flowsheet, where the PLS was first subjected to double sulphate precipitation, then the remaining REEs, mostly heavy rare earth elements (HREE), were recovered by oxalate precipitation (Li, 2011)."

Jan 1, 2016

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By R. Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as an inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1995; Walsh and Rao, 1986; Walsh and Kelly, 1992). In November, 1993, the author inspected the grinding circuit at La Mine Doyon in Rouyn-Noranda, Quebec and made recommendations to recover coarse gold and to eliminate gold traps from the circuit. In 1995, the author salted mineral processing circuits with radioactive gold particles. The gamma and X-ray radiation from gold’s nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment using scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps and improving security.Nuclear TracersWhen particles of gold are placed in a nuclear reactor, some of the gold atoms (Au197) absorb another neutron in their nucleus to form gold’s radioactive isotope (Au198). In the process of radioactive decay, this isotope emits high energy gamma rays and X-rays which are easily detected (even through steel) with scintillometers.Radioactive gold (Au198) has a very short halflife of 2.7 days. At the relatively low activity levels used for tracing, the particles remain detectable with a small hand-held scintillometer for about 10 to 14 days. After 14 days the irradiated gold is close to background levels and within two months it is essentially non-radioactive. The radiation has no effect on the recovery characteristics of the gold particles. The gold radiotracers are very safe due to their very low level of radiation, short half-life, and their inherent physical and chemical stability. However, the use and possession of even mildly irradiated gold is strictly licensed and regulated."

Jan 1, 1997

By K. Musgrave

"The ISO 9000 Quality Management System Standards have become internationally accepted as the way to manage quality assurance. The author has developed a Maintenance Management System Standard using ISO 9001as a model and is working with a major basemetal mining company to implement this. This paper describes the structure of the standard and the steps required for its implementation.Using a management standard ensures that a system is maintained, reviewed by internal audit, and when instances of failing to follow the procedures (nonconformances) occur, that corrective action is taken. It also ensures that regular reviews are made and that the sys-tem is continuously improved.The Standard is designed so that if an organization decides to register to an ISO 9000standard, the Maintenance Management System will be in a format that is compatible and can be incorporated with little effort into the Quality System.IntroductionIn reviewing maintenance operations at many mining companies, and often seeing those same organizations some years later, two recurring issues have been noticed..The first issue is how dependent effective maintenance is upon individual supervisors and crews. In one situation, a mine that had an excellent maintenance system in the 1980s. Now, with new supervisors and crews, it is starting to develop a system that will bring it back to where it once was. No written procedures remain from the earlier excellent system.The second issue is that most operations feel that maintenance is the sole responsibility of the maintenance supervisors and crews. Nothing could be further from the truth. Maintenance, like safety, is everyone’s responsibility. If the operator does not report problems and perform daily checks, and if the production supervisor runs equipment until it fails, then nothing the maintenance crew does will prevent emergency breakdowns and lost production. More importantly, equipment will be operated in unsafe conditions, putting employees at risk and, with today’s regulations, leaving supervisors open to prosecution.The Maintenance Management System outlined in this paper is designed to establish the present best practices as standard procedures, to provide a continual review so that these practices are improved in the future, and to identify instances where the system fails so that corrective action is taken. The mine referred to above is using this approach to make sure that, this time, the system it implements will survive."

Jan 1, 1997

By John B. Hodgeson

AMMONIA is an essential constituent in the production of the ammonium-sulphate and ammonium-phosohate soil fertilizers manufactured by the Consolidated Mining and Smelting Company of Canada, Limited. The fertilizer plant, built in 1930 at Warfield, near Trail, provides a means of utilizing the large amount of sulphuric acid produced from the sulphur dioxide which is removed from the smelter smoke. The plant has an avail-able source of cheap power which makes the production of fertilizer economically possible. The fundamental operations involved in the production of ammonia at the Warfield plant are, first, the manufacture of hydrogen by the electrolytic dissociation of water; next, the recovery of nitrogen by the fractional distillation of liquid air; and finally, the combination of hydrogen and nitrogen in proper proportions and under suitable conditions to form ammonia.

Jan 1, 1938

By D. Haraguchi, S. Izawa, C. Tokoro, S. Owada

"Arsenic is widely known as a toxic element for humans, animals and plants. Because of more stringent wastewater standards not only in Japan but also around the world, research for appropriate and efficient treatment method for arsenic is becoming increasingly important. Coprecipitation or adsorption process using ferrihydrite is widely implemented for dilute As(V) removal from wastewater. In this study, the sorption mechanism of dilute As(V) with ferrihydrite in coprecipitation or adsorption process was investigated. To accomplish this, we conducted batch experiments of coprecipitation or adsorption and compared these results for sorption isotherm and zeta potential. These experimental results showed that sorption mechanism in coprecipitation process depends on the initial As/Fe molar ratio; simple twodimensional adsorption onto the surface of ferrihydrite when the initial As/Fe molar ratio was < 0.4, and some three-dimensional uptake with ferrihydrite when it was = 0.4. We also evaluated the sorption mechanim by analysis of X-ray diffraction (XRD) and X-ray Absorption Fine Structure (XAFS). XRD or XAFS spectra showed that surface precipitation of amorphous ferric arsenate was formed when the initial as/Fe molar ratio was = 0.4, beyond the thermodynamic bulk precipitation range for ferric arsenate.INTRODUCTIONArsenic is toxic to animals, including humans, and long-term exposure to arsenic via drinkingwater causes cancer of the skin, lungs, urinary bladder, and kidneys, as well as other effects on the skin such as changes in pigmentation and thickening (Ghosha et al., 2008). Elevated levels of arsenic are often present in the environment as a result of the weathering and dissolution of minerals as well as in response to numerous anthropogenic sources including the discharge of mine wastes, coal fly ash and the use of pesticides that contain arsenic (Nriagu, 1994; Singh et al., 2007). Indeed, the potential for arsenic exposure affects many people, as evidenced by several million people in Bangladesh and India being at risk of exposure via drinking water obtained from contaminated groundwater sources (Ahmed, 2001).Acid mine drainage (AMD) containing arsenic is a global environmental problem (Dold, 2008; Liang and Thomson, 2008) that also affects Japan, which has many abandoned or closed mines that have been generating AMD for the last few decades (Masuda et al., 2008). Several such facilities in Japan produce AMD containing dilute concentrations of arsenic that exceed Japanese effluent standards (0.1 mg/dm3) (METI, 2006). For example, AMD from the abandoned Horobetsu sulfur mine, the largest AMD source in Japan, contains approximately 10 mg/dm3 arsenic."

Jan 1, 2012

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015