Search Documents

By M. Mirnezami, J. A. Finch, S. Uddin

A fast, reliable and practical way of measuring zeta potential using sedimentation potential method is proposed. A cell was designed along with the instrument control software to determine the required variables simultaneously i.e. sedimentation potential, specific conductivity, volume fraction of solid as well as pH. High purity alumina and silica powders were used as test samples. Measured zeta potential using the proposed technique was comparable with the results by electrophoresis.

Jan 1, 2009

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By E. Talebi, P. Roghanchi

"This study aims to discuss personal and behavioral parameters contributing to heat-related accidents. To study the prevention approaches, it is essential to look at the various factors at the individual, management, and industrial levels. Qualitative risk analysis methods are used based on the public data in the USA to find the impact of the environmental and behavioral parameters on the heat stress and heat strain of mine workers. The effects of individual factors such as worker experience, age, fitness, lifestyle, acclimation, and more are illustrated. The significance of factors such as the roles of the mine management and regulatory agencies are addressed.INTRODUCTIONOccupational hazards in mining industry endanger the health and safety of the workers and productivity loss for mining companies. Among those hazards is the exposure to excessive heat that has adverse effects on the health of mine workers. The intensity of heat load is a significant factor in fatal and non-fatal heat-related accidents. Severe environmental conditions combined with a high level of activity in the mining industry increases the vulnerability of individuals to health and safety hazards (Ngwenya, Oosthuizen, Cross, Frimpong, & Chaibva, 2018). Lack of regulations and legislation addressing the heat issue in the mining industry (i.e., underground and open pit mines, processing plants) also raises widespread concerns.Along the climate change, various sources contribute to the overall heat load at a mine site (Hanna, Kjellstrom, Bennett, & Dear, 2011; Kjellstrom, Lemke, Hyatt, & Otto, 2014). In underground mines, the majority of heat comes from different sources such as geothermal gradient, equipment, auto compression, groundwater, and blasting (Maurya, Karena, Vardhan, Aruna, & Raj, 2015). On the surface, however, the majority of heat load can be sourced to solar energy. The exposure to excessive heat might result in heat-related illnesses, fatigue and fainting, loss of concentration, performance reduction, and production loss (Kocsis & Sunkpal, 2017; Roghanchi, 2017). The severity of the effects depends on duration and level of exposure and the response of an individual to heat stress. The response of an individual is influenced by different factors including age, gender, fitness, lifestyle, experiences, and past medical history."

Jan 1, 2019

By A. J. Rigby

The wear mechanisms of the tuyere lines of Peirce-Smith and Hoboken converters are a subject of endless debate and speculation. However, there has been an indication that one of the primary factors in the deterioration of tuyere lines is due to the batch operation of the converting process. The cooling of the brick in the tuyere line during out-of-stack times leads to shrinkage of the brick and resultant opening of the joints. Subsequently, on re-entry of the tuyere line into the bath, the joints become penetrated with matte and re- expansion of the brick is prevented. It is thought that this regular cycle of exiting the batch for slag skimming and replenishment of matte and re-entering for further blowing leads to a gradual “ratcheting” of the tuyere brick lining. If no expansion allowance is furnished between the endplate and the endwall of the lining, then the generation of damaging compressive stress is unavoidable. INTRODUCTION It is generally accepted industry-wide that the integrity of a refractory lined vessel is determined by an inextricable combination of refractory brick quality, the caliber of the lining design and installation, and the severity of the process inflicted upon the high wear areas of the vessel lining. Rigby has summarized the concentrated attempt, over the past several years, to optimize the microstructural, chemical, and fracture properties of the refractories used in non-ferrous pyrometallurgical vessels. Furthermore, lining design concepts involving larger and longer brick and the extent and positioning of expansion allowance in the joints have been extensively trialed. All these efforts have provided some, but not startling, improvements. The simple fact is that a vessel lining composed of bricks with an optimized microstructure and chemical inertness must installed with a well-conceived design to decompress the lining stresses that are generated by the batch operation of copper converters. REFRACTORY QUALITY Converting is conducted by injecting air into the molten matte and white metal for the very purpose of generating iron and copper oxide slags. These slags must be contained by a refractory which, by its mineralogical formulation, is optimized for chemical inertness.

Jan 1, 2019

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By D. R. Boyle

"The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite _ arsenopyrite _ galena _ Bi-Sb sulfosalts _ chalcopyrite _ tetrahedrite group _ sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was transported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. R. Boyle

"Abstract - The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite > arsenopyrite > galena > Bi-Sb sulfosalts > chalcopyrite > tetrahedrite group > sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was trans- ported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD&apos;s , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

Accurate hematite solubility data are required to construct predictive solution chemistry models for complex hydrometallurgical solutions. These data are useful in understanding Fe(III) speciation and precipitation in a variety of hydrometallurgical processes. Hematite solubility data were generated in 10 to 70 g/L H2SO4 solutions and at temperatures from 130 to 270°C, using specially modified titanium autoclaves. These measurements represent an improvement over previous experimental data because of better in-situ filtration of the sample aliquots, the approach to equilibrium via hematite dissolution, and the inhibition of Fe(III) reduction on titanium surfaces. Fe(III) reduction was particularly studied to evaluate the inflationary effect of Fe(II) on hematite solubility measurements. Chromate was found to reliably inhibit Fe(III) reduction on titanium. Finally, the generated hematite solubility data were used to construct a solution chemistry model using the OLI software.

Jan 1, 2006

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

Five years ago, VALE Base Metals (then INCO), approached Pelton&apos;s group at McMaster and described a challenging mineral separations problem. The McMaster group has a strong track record in colloids, polymers, and chemical additives for papermaking; however, they had no experience in mineral processing. They proposed employing hydrophobic nanoparticles to replace conventional low molecular weight, water-soluble flotation collectors. Over the last five years, Vale, together with the Ontario Government (OCE) have funded two graduate students at McMaster who have worked closely with flotation experts at Vale. Experiments involving both very clean model mineral suspensions at McMaster and complex ores at Vale, have shown that hydrophobic nanoparticles do indeed function as collectors. Key nanoparticle properties and mechanisms have been identified and the technology has been protected in patent applications. Efforts to commercialize the technology are on-going. We believe that this project is a good case study demonstrating the advantages of industry-university collaboration and the use of outside experts, who may come up with novel solutions to complex problems.

Jan 1, 2011

By Mark W. Bartlett

Program Objectives ??Identify and implement a tool for haul truck drivers that: -Reduces or eliminates fatigue-related injuries and fatalities -Reduces accidents and equipment damage ??Following evaluation period, apply tool where most effective Why do We Need a Fatigue Monitoring Tool? ??Everyone has probably fallen asleep while driving ??Driver fatigue is a major source of property damage and serious haul truck serious incidents ??To protect ourselves from the other ?tired?driver ??To know when to ask for relief ??To know when we are seriously distracted from driving ??To measure improvements in sleep incidents based on shift changes and intervention ??To help prevent incidents like the following:

May 1, 2011

By R. H. Brooks

Blasthole stoping methods were introduced at Birchtree Mine as an alternative to the original cut-and-fill and shrinkage stoping methods. The object was to take advantage of the ore structure and conditions, and achieve increased productivity. This paper outlines the design, operation and economics of three areas which utilized blasthole stoping. The 108areafrom 2300 level to 1500level was converted from cut-and-fill to sublevel blasthole stoping based on a block mining-and-filling sequence. The second area, the crown pillar of 110 mechanized cut-and-fill stope below 500 level, was recovered using horizontal rings drilled from raises within the ore zone. The third area, the 83 orebody from 1300 level to 1100 level, used the vertical crater retreat (VCR) method with large-diameter blastholes. Blasthole stoping has increased productivity and improved operating conditions.

Jan 1, 1979