Search Documents

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited's rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By Euler De Souza, Kyle Penner

"Booster fans play an important role in assisting main fans by boosting the air pressure of the ventilation air passing through it. The correct placement of underground booster fans in a mine is a critical decision since it not only influences the mine’s operational capacity in terms of costs and efficiency, but also affects safety and environmental conditions. There are many booster fan installations around mines that are inappropriate, in some cases resulting in system failure (fan stall) or in a major negative impact on mine production. Inadequate booster fan placement has resulted, in some cases, in extensive air leakage which has compromised the economics of the operation and, in other cases, in recirculation of contaminants which has seriously compromised safety. This paper provides guidelines for proper design and siting of booster fans underground, to not only achieve an economic ventilation system but to create safe work conditions and efficient atmospheric conditions. Procedures for the planning, installation, operation and maintenance of booster fans are also presented. A case study illustrating the design and siting of a major booster fan installation in a potash mine, supported by computational fluid dynamics analysis, is presented.INTRODUCTIONIn large underground operations with complex ventilation networks offering high resistances, the never ending increased required quantities of air can almost only be supplied through use of high pressure main fan systems. These fans may, in effect, induce significant leakage losses in the system, having a negative impact on safety performance. In such cases, booster fans can be designed to decrease the main fan pressures and reduce the leakage flows, improve system efficiency and reduce costs. In well designed systems, booster fans can thus be used to redistribute the airflow and assist the main surface fans.When the pressure supplied by the main fans is insufficient to meet the ventilation circuit pressure requirements, booster fans are placed in strategic locations where pressure boosting is essential. Booster fans are typically sited in sections of the circuit offering high ventilation resistance and requiring this form of ventilating air motivation. Booster fans are thus required when the mine expands, and so the resistance of the ventilation network, and the primary fans no longer can supply the required pressure and flow."

Jan 1, 2019

By A. E. Hall

"This paper summarizes findings of a two-month investigation in Zambia and Zimbabwe and a one-month visit to Britain in1990-1991. United States contacts have supplied information about that country.Zambia's political unrest and severe devaluation, combined with developments in Namibia and South Africa, enhanced staff recruiting problems in the School of Mines. Zimbabwe has a strong and developing mining department. The departments of mining in the United States and Great Britain are readjusting and contracting due to the reduction in the scale of the industry.The above factors are reviewed and their impact on the countries evaluated.IntroductionCanada trains the majority of its mining engineers domestically but a significant number are recruited from other countries. Examination of the qualifications of 200 professional engineers registered in the mining discipline in British Columbia showed that125 received their first degree from a Canadian university, 33 graduated from institutions in the United States and 42 from the rest of the world including 30 from the United Kingdom. This is a rough and-ready sample but it indicates that developments in the education of mining engineers in the United States and in Britain are relevant to the Canadian mining industry.The recent changes in the world economy and political structure have significant implications for the mining industry and for the supply and training of engineers. Change in eastern Europe coupled with the downturn in mining, especially in the European coalfields, has enabled many engineers to travel freely to the West. The low gold price and the legislative changes in Africa that have improved access to education for Africans with the ability to fill responsible positions, have reduced the South African mining industry’s overseas recruitment to a minimal level. The Australian recession has also lowered their recruitment of mining engineers from other countries."

Jan 1, 1993

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By Lise-Aurore Lapalme

Structure of the Presentation ? sustainable development and its social dimension ? challenges that mining is facing ? responses by industry ? corporate social responsibility ? the role of government Sustainable Development ? new perspective on how we view development ? consider how minerals and metals contributes to sustainable development ? challenge to better understand economic, environmental and social aspects ? make social aspects more broadly understood and appreciated

May 1, 2002

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By Wang Wenqian, George W. Poling

"Devices and flowsheets for recovering fine placer gold are reviewed. Inefficiencies of gravity processing techniques are documented and discussed. Prospects of combining gravity and froth flotation techniques are presented. Possibilities of using other separation techniques, such as magnetic and electrostatic devices are also discussed.IntroductionSeveral new methods for beneficiating different types of placer ores have been developed in the last two decades. Improved efficiencies in the recovery of fine particles have been achieved by improving gravity flowsheets and machines as well as by developing multiple treatment techniques involving flotation, magnetic and electrostatic separations. Placer gold processing, however, has been an exception to some extent. Gravity concentration using riffled sluices accompanied by mercury amalgamation is still the main method in use today. Because of this, the recoveries of fine gold and the other associated values are often similar to those achieved several decades ago. For example, very few sluice systems recover significant placer gold finer than 100µm in size.Only a few proposals for using alternatives to simple gravity methods for recovering fine placer gold can be found in the published literature. The fixed, low gold price discouraged research in this field for many years. Development of more efficient processes has not kept pace with the recent rapid escalation in the price of gold. Froth flotation for saving fine placer gold might now prove economic, for example. This paper reviews literature published on the recovery of fine placer gold over the period 1907 to 1980. Suggestions for improving the performance in this field, based on the authors' current testwork, are also presented."

Jan 1, 1983

By RALPH R. STEA, John H. Fowler

Clay, quartz sand and lignite deposits overlie Carboniferous rocks in central mainland Nova Scotia. Recent evidence indicates that these deposits are fairly extensive. Sands consist of almost pure angular quartz grains. Clays are highly plastic and range in colour from black through grey and blue to mottled red and white. Palynologica/ information dates the sediments as Ear{y Cretaceous, and mineralogical studies show them to consist primarily of quartz, kaolinite and mica. There is not yet enough evidence for detailed stratigraphic description, but sequence and thickness of sediments are known to vary greatly over short distances. Drill logs from Musquodoboit Valley recorded Cretaceous sediments at 168 m thick. Of the three active pits in Cretaceous sediments of central Nova Scotia, two are for silica sand production and are located at Elmsvale and Brazil Lake while a third pit at Shubenacadie produces clay for manufacture of structural clay products.

Jan 1, 1984

By J. P. Nowlan

"This paper is an attempt to outline the structural problems at the Cochenour Willans mine, in so far as their details have been tentatively worked out. It must be emphasized that there are considerable data that can be interpreted in more than one way, and that further work may modify or completely change some of the hypotheses presented herein. Certain features, however, are sufficiently constant to warrant reliance on them when searching for extensions of orebodies.As the individual ore shoots usually have relatively small dimensions, but are often very high grade, structural details are of more than usual significance in laying out a mining programme. An illustration of this is a small shoot recently located and mined as a result of studying a minor slip cutting off a part of high grade gold ore in No. 319 stope. The shoot, which is bounded on three sides by slips, and on the fourth by the original stoping, was roughly triangular in plan, 20 feet on the base, and 40 feet in length. The average width mined was 4.5 feet, but the gold obtained totalled over 1,800 oz.The property lies in Dome township, east of McKenzie island, and consists of an original group of thirteen claims acquired from the Cochenour Willans syndicate, plus one additional group of five claims obtained by purchase from the Kelson Red Lake Gold Mines, Limited, and one other claim that rounds out the southeast corner of the block.The claims of the original group were staked by W. M. Cochenour, Dan Willans, and Horace Young, during 1926 and 1927. The Cochenour Willans Syndicate was formed in 1928, and until incorporation of the present Company work was carried on at varying intervals by several different interests, including Ventures Limited, Hollinger Consolidated, who sank a shaft to open up the 150-foot level, and by the Syndicate itself. The first ore from the property was shipped to the Gold Eagle mill by the present Company in 1939, and amounted to 4,959 tons, from which 2,360 oz. gold was recovered. The first brick was poured in December, 1939, and production has been continuous since that date. To the end of June, 1946, gold having a value of $5,982,000 has been produced from 345,033 tons of ore treated."

Jan 1, 1954

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By R. Vergunst, E. A. Devuyst, G. Robbins

"INTRODUCTIONThe Inca process for continuous cyanide removal from industrial wastewaters was patented in 1984 by G.J. Borbely, et.al. (1). The process requires SO2, air, lime and a copper catalyst. Both free and complexed cyanide are oxidized to cyanate in the pH range 8 to 10. Cyanide bound to iron is removed by precipitation as a ferrocyanide insoluble salt and other base metals are removed as hydroxides.The process was piloted in 1982 on barren bleed solution at Campbell Red Lake Mines Ltd., Ontario (2). Since 1982, the Inca SO2-air cyanide removal technology has been applied in twelve commercial installations. The process has significant advantages over other commercial processes in the completeness of cyanide removal and lower reagent requirements and costs.COMMERCIAL INSTALLATIONSBy the end of 1988 Inca will have applied its patented cyanide removal technology to twelve commercial operations. Three of these, namely Scottie Gold Mines, Dupont of Canada Expl. Baker mill and Carolin, all in British Columbia, Canada, have ceased cyanidation operations but SO2-air cyanide destruction results were good for all mills, particularly so for over two years for the Scottie mill.Removal of cyanide from CIL slurry tailings is applied at Equity Silver (9,500 tpd) and Inca's new 1,200 tpd mill at Inca/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3,600 tpd) and Canamax's Ketza River operation (360 tpd). Repulped tailings from Merril-Crowe flowsheets are treated at Total Erickson's Mount Skukum mill (300 tpd) and Skyline's Johnny Mountain mill (200 tpd) and barren bleed at Inco/Queenston's McBean mill (500 tpd). Lynngold's MacLellan mill (1,800 tpd) treats pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating in Kitchener, Ontario. Many of the above commercial operations were described in some detail in previous publications (3,4). Typical installations are described in this paper. A summary of operating results is given in Table 1."

Jan 1, 1989