Search Documents

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By P. A. Gonzalez Contreras

Scorodite is considered as a secondary mineral formed from the product of weathering of primary minerals by chemical or biological reactions. In the case of biological scorodite formation, microorganisms mimic and accelerate what in nature takes a very long time, i.e. biocrystallisation. The goal of the biological scorodite formation is to form very stable arsenic crystals suitable for long-term and safe disposal. The biological formation of scorodite is a novel combination of biological oxidation, biocrystallisation, and proper bioreactor design to achieve the biological formation of scorodite crystals in one step. We have explored simultaneous biological arsenic and iron oxidation at 30ºC and at 70ºC leading to arsenic-jarosite phases and scorodite, respectively. As biologically formed scorodite crystals are very stable (TCLP < 1 mg/L As (V)), the risk of arsenic toxicity is minimized when leaching takes place. This process is suitable for arsenic concentrations above 0.5 g/l As achieving up to 20 mg/l As in the effluent. This biological scorodite formation system is a selfsufficient bio-oxidation system and therefore many new applications can be explored such as reprocessing of arsenic trioxide, orpiment or calcium arsenate to scorodite crystals for a stable and safe disposal.

Jan 1, 2014

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

Electric Vehicle Controllers Ltd. ?EVC started in 1981 ?Underground electric locomotive drive systems ?Developed tandem load sharing system and radio ELOS controls ?Locomotive autonomy systems ?Entered space technology development in 1999 with NORCAT to develop Mars drill for CSA ?Commercial distributor for drilling systems, lunar physical simulants, electric mobility systems and lunar mining technologies

May 1, 2009

By Ramesh Subramanian

Overview Background / History Undergraduate Programs Mining Engineering Chemical Engineering Mechanical Engineering Graduate Programs and Research Student Enrolment (2002 -) Future Plans

Oct 1, 2010

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By B. Kruger

The Dundee Precious Metals Tsumeb Smelter has evolved over the last decade to meet the challenges and opportunities brought about by a changing copper concentrate market, technological advances, environmental legislation as well as social and political changes. The paper discusses some of the challenges, successes and lessons learnt through the expansion and modernization of its smelter complex. It considers the details and impact of the transition from slag granulation to that of slag slow cooling as well as the improvement program that was implemented to more than double the refractory campaign life of the Ausmelt furnace from around 6–9 months to 15–18 months. In addition, given the evolving world we live in, it considers the challenges that the smelter faces today, not the least of it being how to remain relevant in an age of digital and other 4th Industrial Revolution disruptions. INTRODUCTION Dundee Precious Metals Tsumeb (DPMT) Smelter is located just outside the town of Tsumeb, in the Oshikoto region of Namibia. It is the largest town in the region with a population of approximately 45,000. The smelter was built in the early 1960s to treat concentrate from the nearby Tsumeb copper mines. Construction of the site was completed in 1962 and the smelter was officially commissioned in 1963 by Tsumeb Corporation Limited (TCL). At the time the smelter consisted of a lead section (including a refinery), a copper section and plants that produced cadmium, sodium antimonite and arsenic trioxide. Production commenced in early 1964, with 3,500 tonnes of copper and 6,000 tonnes of lead being produced per month. TCL was acquired by Gold Fields South Africa in 1988, and a few years later the lead section was shut down due to reduced lead content of the mined ore. In mid-1996, all mining and smelting operations were halted due to labour strikes. Ongopolo Mining and Processing Limited (OMPL) re-opened the mines and the smelter in 2000, only operating the copper section of the smelter. At the end of 2008, all mining operations were halted by the new owner of OMPL, Weatherly Mining International, while the smelter continued to operate. The closure of the Weatherly owned mines in Namibia, the primary feed source to the Tsumeb Smelter, meant that the smelter had to transition its business model from operating as a ‘captive smelter’ to that of a ‘toll smelter’. Its Ausmelt Top Submerged Lance (TSL) smelting technology and various ancillary plants made it especially suitable for accepting and treating complex concentrates that were available on the global market.

Jan 1, 2019