Search Documents

By F. Boudreault, C. Hendricks, M. Scobie

Drilling accuracy represents an important quality control factor in minimizing dilution. Apart from geology, the factors governing drilling accuracy are largely within the control of the mine. Setup location and alignment, as well as actual drilling accuracy, can all be monitored toward their improved control. Trajectory deviation during drilling, although usually beyond the control of even the most experienced and conscientious driller, can be accounted for (if not full controlled) by down-hole surveying of blastholes prior to explosives loading. This paper reviews the available instrumentation for improved drill setup and recent field experience with several commercial systems designed for monitoring borehole deviation. It reports on a recent survey of 50 Canadian mines which use blasthole stoping and addresses the reasons for the apparent lack of interest in instrumentation: i.e. does this reflect a lack of awareness of the technology, perceived inadequacies in its performance or a predominant reliance on productivity (drilling and mucking) as a measure of operational efficiency? The survey findings supported the latter viewpoint and showed that very few Canadian mines operate drilling incentive programs that are related to drilling accuracy.

Jan 1, 1994

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

"The first record of a kimberlite found in Canada (1946) was the identification of thin dykes intersected while drilling for gold in Michaud Township, Ontario.Sampling of the Munro Esker (1964) in the Kirkland Lake area, Ontario, by the Geological Survey of Canada identified the occurrence of detrital grains of pyrope garnets along a length of 35 km of the 113 km tested. A search for the source of the garnets resulted in the identification (1968) of a narrow subsurface kimberlite dyke in the Upper Canada Mine. This discovery resulted in a staking rush. Unfortunately, subsequent work did not identify the source of the kimberlite indicator minerals.During 1978 the Ontario Geological Survey started a multi-discipline study of 29 townships (2560 krn2) in the Kirkland Lake area, to encourage exploration for gold, base metals, and kimberlites. Back-hoe sampling (1979 to 1982), where the overburden was thin, and reverse circulation drilling, in areas of thicker drift, yielded samples of the till. These were analyzed for several elements and a mineralogical identification of the heavy minerals was completed. Pyrope and chrome diopside grains were identified.Studies of the Pleistocene geology indicated only the most recent direction (167 degrees) of ice advance (Matheson) and the associated deposits, out of a possible three advances known to occur in the general region straddling the Ontario-Quebec boundary, is present in the immediate area of Kirkland Lake. Contouring the distribution of pyrope grains (1990) showed a concentration centered over an area of 616 km2 extending down-ice from Gauthier Township. This included a smaller area containing chrome diopside grains. Kimberlite boulders were identified (1981) in gravel pits on the Munro and Misema River Eskers located within this anomalous area. The next step would be to use the airborne geophysical data to locate the kimberlite pipes which yielded the indicator minerals and boulders. The source area is likely to be in the northern half of the Ontario Geological Survey study area."

Jan 1, 1992

By B. Misra, B. S: Sastry, Kollu S. Rao

"This paper reports the results of a finite element study of the geothermal heatflow into dry mine airways. For isotropic and unsteady state conditions the heatflow into mine airways is studied for a range of surface heat transfer coefficients between rock and air, and age of the airway. Dimensionless temperature gradient values are presented in tables for different values of Boit and Fourier numbers and the results are compared with Starfield tables and Gibson algorithm. It is found that Starfield tables have consistently over-predicted the G values with errors ranging from 2% to 10%. The differences between results obtained from the finite element study and the G values calculated from Gibson's approximation method are mapped. The small error values over a large range of Fourier and Biot numbers confirm the suitability of Gibson's algorithm to rapidly calculate G values for estimating the heat transfer from surrounding rock to mine air.IntroductionIn many underground mines heat is a major problem, and the provision of acceptable working conditions requires considerable expenditure on ventilation systems. The rational design and operation of these systems depend upon an understanding of the various sources of heat in the mine. The natural source, i.e. geothermal heat, contributes up to 80% of total heat added to mine air and it is difficult to analyze and predict the heat owing to a number of influencing variables. The problem of geothermal heat flow has been studied by many investigators (Goch, 1940; Starfield, 1966; Hemp, 1987; Amano et al., 1982; McPherson, 1986).The primary concern of this paper is to develop a better ready reference dimensionless transient temperature table for estimating heatflow at any stage of mine airway life."

Jan 1, 1994

By K. Cybulski

Coal dust explosions still remain the main hazard in the coal mining sector, notwithstanding their relatively wide recognition compared to other hazards and the development of effective methods of prevention. Coal dust explosions are still the cause of numerous catastrophes, often leading to fatalities. Fortunately, they rarely occur, and it is for this reason that their hazardous impact is often underestimated. This problem in Poland is being exclusively solved by the Central Mining Institute, Experimental Mine Barbara. Here, basic research on the phenomenon of coal dust explosions and prevention methods is carried out, as well as investigations into the causes and circumstances of past accidents. After 15 years of no coal dust explosion accidents in Poland (1987?2002), a few coal dust explosions have recently occurred, with tragic consequences. These events have taken place not only in hard coal mines, where the presence of dangerous coal dust is the result of common production cycle, and safety measures against coal dust explosions are subject to specific regulations, but also in coal-fired power plants. This is of special concern because prior to 1987, such accidents had been been reported only for coal mines and not for coal-fired power plants. In recent years, two dust explosions occurred in Polish power facilities: the Dolna Odra and Turow power plants. In both cases, coal dust explosions occurred in the fuel supply system, but biomass dust was also involved. The explosions caused significant damage to the systems and buildings. This paper gives description and schematics of the regions of catastrophic coal dust explosions that have occurred in recent years in Poland, as well as the results of post-accident investigations, presenting the coal dust explosion hazard at the accident scene The results specify in detail the state of safety measures against coal dust explosions in light of the relevant regulations in force, including amount of deposited coal dust, content of incombustible matter in coal dust, free moisture content in coal dust, state of coal dust explosion safety zones, and state of explosion barriers. The conclusions from the site inspection and post-accident investigations presented enable us to determine locations of explosion initiation, probable ignition sources, range of explosion flames, and explosion barrier performance. A complete elimination of coal dust explosion hazard at the site of dust deposition is practically impossible to achieve. Similarly, a total elimination of ignition source, which may be related to the occurrence of other natural hazards, equipment malfunction or human errors, is impossible. The examples of tragic events that took place in Polish coal mines and coal-fired power plants highlight shortcomings and mistakes made in terms of assessment and prevention measures taken against the coal dust explosion hazard.

Aug 1, 2013

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

?Bank Lending to the Mining Sector affected by 2 broad factors since Mid 2008: 1. Economic Downturn (?the Real Economy?) for mining companies directly reflected in lower metal prices (current and forecasted). In the case of gold companies, minimal effect. 2. Financial Crisis (?the Credit Crunch?) as it has affected the lending activities of those banks active in the mining sector.

May 1, 2009

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By C. Bourgoin

"The factors constraining productivity in the mining of narrow vein ore deposits are numerous and often interdependent. This paper concerns mining techniques capable of reducing some of these constraints in the case of vein deposits whose dip is less than 45 degrees. Modifications of conventional mining methods as well as suggested new developments are presented, as are matters pertaining to the mechanization of operations as a mean of increasing both productivity and work safety. IntroductionThe mining of vein deposits, whose width (thickness) is generally less than 2 metres and whose dip is often variable, calls for the use of varying stoping procedures as well as appropriate infrastructure and equipment. In the case of intermediate dips (15 degrees to 45 degrees), it is generally conceded that the degree of mechanization is limited and that ore removal via gravity is impossible. This paper proposes certain innovations in matters of equipment use and stoping methods, together with certain technical data pertaining to the application of these new procedures Stoping MethodsTo mine vein deposits, one must choose a method that can adapt to irregular ore limits and allow, as well, for good ore recovery with as little dilution as possible. In addition, it is important to minimize development work in waste rock. In principle, one selects a method that is both safe and profitable; this method will be defined mainly by the nature of the vein deposit and its dip, by the competency of the rock formations and by certain technical considerations. Moreover, the stoping procedure in a given deposit may well change with time as a function of new layouts or new equipment."

Jan 1, 1994

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By E. G. Joe

The continuing increase in costs for power and fuel are affecting significantly the cost of milling Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors, carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that, in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc .ore mills were moderate in energy consumption, and uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. Although plant heating costs varied somewhat with location, it was apparent that the lowest heating costs were achieved by those plants built with proper insulation and energy conservation design. If the cost per million British thermal units is taken as $2.00, the mill energy costs generally ranged from 40ft to $1.20 per ton.

Jan 1, 1979

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By R. Lanthier, A. Broussaud, J. C. Guillaneau, D. Hodouin

This study presents a method for upgrading the information extracted from the measurements given by the sensors of a pilot grinding circuit. For that purpose raw signals are combined to process models for extracting, through filters, the best information on the process state. Two different filters are used; one is based on steady-state mass balance constraints and the other one uses dynamic mass balance equations allowing for material accumulation in the equipment. The filters are designed and tuned with the help of a grinding circuit dynamic simulator and are then implemented in the pilot plant. Their performances and usefulness are discussed.

Jan 1, 1989

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By J. E. Carter, D. P. Wall

"This paper details the highlights of the open-pit and underground operations of Mclntyre Mines Limited in the Smoky River area of Alberta. Mining methods, operating equipment and manpower are outlined, followed by a discussion of reclamation and environmental control.IntroductionMcintyre Porcupine Mines Limited was incorporated in 1911 and for many decades was known primarily as a gold producer in the Porcupine district of northeastern Ontario. The company, however , has held coal leases in the Smoky River area, near Grande Cache, Alberta, since 1921. Preliminary studies were carried out in the region from 1959 to 1963. In 1964, Mitsubishi, a leading Japanese trading company, (on behalf of Mcintyre), investigated the area as a possible source of coal for the Japanese steel industry. The initial report concluded that Smoky River coal was of high quality, comparable with some of the best metallurgical coals in the world."

Jan 1, 1981