Search Documents

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By J. E. McMenamin, R. B. Hall

"With the emphasis in the past decade on larger and more efficient equipment for open-pit operations, the Normandie mine of the Asbestos Corporation has followed the trend, switching from the smaller type of percussion drills to down-the-hole rigs. One 5 Y2 -in. percussion drill is still in use, but is limited to a ""smooth blasting"" role or to the control of the slope on final benches.In keeping with the times, an attempt was made to eliminate, as much as possible, the use of high explosives and to maximize the percentage of ammonium nitrate -fuel oil mixture. As the concentration of ground water increased with increased mining depths, small pumps were initially employed for the dewatering of boreholes. This proved unsuccessful, and a hole-blowing rig was built and a conversion to plastic liners made. The acquisition of a bulk-mix AN-FO truck has permitted the changeover from an AN premix to an ammonium nitrate prill -fuel oil combination at the borehole."

Jan 1, 1966

By R. C. E. Bray, Peter Price

"The property of Pamour Porcupine Mines, Limited, is in the eastern Porcupine area, about 12 miles northeast of Timmins. It covers parts of lots 3-6 (inclusive), cons. 5 and 6, Whitney tp., Cochrane district, Ontario. It is an amalgamation of the old La Palme, Three Nations, and Porcupine Grande properties.The first discovery on the Pamour was made in 1911. During 1911 to 1914 a small shaft was sunk on the Three Nations vein to the 200-foot level and a 100-ton stamp mill was put in operation, but only a small production was achieved. The property remained idle from 1914 to 1923. In 1924 some diamond drilling was done along the Keewatin-Timiskaming contact with some encouraging results, but the gold mineralization encountered was too low in general at the price of gold then prevailing to warrant further · work. The increase in the price of gold revived interest in the area, and the above noted amalgamation was effected in 1934. Options were taken and successively dropped by two large mining companies. Following this, exploration both on the surface and underground was started by Quebec Gold Mining Corporation, Limited. Diamond drilling in the early part of 1933 showed considerable ore in conglomerate and greywacke to the east. In the middle of 1935 Noranda Mines, Limited, assumed control and management. A new shaft was sunk and the property was ·equipped with a mill having an initial capacity of750 tons a day. This was subsequently enlarged to 1,500 tons a day.From the commencement of milling (May 16, 1936) to the end of 1946, 5,025,545 tons of ore having an average grade of 0.1327 oz. a ton ($4.64 at $35 an oz.) have been mined and milled."

Jan 1, 1954

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006

By A. W. White

Introduction To discuss all the technical details of incorporation laws, security laws, underwriting procedures, codes, and ethics-as laid down by varous associations -would be impossible in the time which has been allotted to me. My remarks, therefore, will be made in a very general way and will naturally be coloured with experiences which my firm and I have had. There is a common expression that "money makes the mare go". I hardly have to mention here that the best prospect in the country is of very little value unless its prospects can be developed-and this requires large capital expenditures. The art and problems surrounding the raising of this money is a long and interesting story. Since by its very nature mining is risky, the appraising of its risks in the many phases of its development programme is continuous. Very few men-if any-and very few corporations -if any -can afford to take all the risk of mining. Because of taxation policies-and the very scheme of present-day living -the truth of this statement can be seen throughout the whole industry by a close examination of the records. Since this is so, it is essential that the mechanics of distributing risk on a sound, and equitable basis be known to those engaged in the business and to the investor or spectator who proposes to risk his funds in the industry. Perhaps the greatest stimulant to modern business activities has been the creation of corporate bodies. It is evident, from the number of charters being granted by various jurisdictions, that this method of doing business is becoming more and more important. A limited company -or corporation-can be defined as a fictitious person existing solely in contemplation of the law.

Jan 1, 1951

By R. Laucournet, E. Billy, M. Joulié

Today Li-ion batteries are considered as one of the most attractive available energy storage solutions. However in order to overcome environmental, legislative and economic issues, the management of used batteries has to be considered and mainly the recycling. The present paper deals with the recycling of used Li-ion batteries and the recovery of high value metals from active materials of electrodes. Lithium nickel cobalt aluminum oxide (NCA) and lithium manganese nickel magnesium oxide (LMNM) cathodes, which contain most of valuable elements typically used in the composition of active materials for Li-ion batteries are investigated by a hydrometallurgy route. The process is divided into two steps: the materials leaching and the elements recovery by a selective chemical separation. Some experimental parameters (acid nature, concentration, time and temperature) are studied to determine the most efficient conditions of dissolution. Then, the valuable elements such as nickel, cobalt and manganese are selectively recovered with a high efficiency close to 100 % and with a high purity by precipitation. By this study, an adaptable hydrometallurgy process can be defined according to the composition of Li-ion batteries to recycle.

Jan 1, 2014

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014

By E. Krause, V. G. Papangelakis, S. Garg, R. Mahadevan, E. Edwards

"Bioleaching uses iron and sulfur-oxidizing bacteria to extract base metals from sulfide minerals. As bioleaching involves breaking the iron-sulfur bonds by ferric attack, the biologically mediated rate of iron oxidation is recognized to play a key role in influencing the overall kinetics. In this study, we investigate the catalytic ability of an indigenous AMD culture for oxidizing Fe(II) in solution. This culture was subsequently adapted on pyrrhotite tailings (0.6% Ni) by gradually increasing the solids loading. Results from this study show that such an adaptation reduces the initial lag phase in the biotic oxidation of Fe(II), thereby allowing for a higher Ni extraction when compared to experiments with an un-adapted culture at a similar solids loading. The use of adapted cultures also helps to reduce the residence time for bioleaching of Ni from pyrrhotite tailings. INTRODUCTIONAs the world demand for pure base metals grows; the mining industry is increasingly faced with the burden of processing lower grade ores and mining waste streams in order to recover the occluded metal VALUES ((Watling, 2006). The extractive metallurgy of nickel from sulfide minerals focuses on using a combination of mineral processing, pyrometallurgical (smelting) and hydrometallurgical techniques to extract Ni from its ore bodies.Pyrrhotite (Fe1-xS) is commonly found in association with pentlandite and chalcopyrite in sulfidic Ni ores, such as those found in Sudbury, Ontario, and in Russia, e.g. Norilsk. The vast majority of this pyrrhotite needs to be removed using mineral processing techniques, in order to minimize the Fe and S contents of the concentrates that proceed on to smelting. If all pyrrhotite were left in the concentrate, much more slag and SO2 would be produced, and the smelter throughput would be limited. Beneficiation of Ni sulfide ores leads to the rejection of unwanted constituents as mining wastes, which may still contain extractable amounts of Ni (Edgar Peek et al., 2010)."

Jan 1, 2012

By D. Marotte, M. David

"A new exploration procedure is proposed for volcanogenic massive sulphide deposits of the Abitibi belt. ""Samples"" of acidic volcanic rocks (Si02 > 60%) were compiled from the literature. From the 574 samples collected, 322 were used in each of a number of experiments. Forward inclusion linear discriminant analysis performed on the untransformed geochemical data shows a general depletion in Na20 and CaO along with an enrichment in MgO for a ""proximal"" group of samples relative to a ""distal"" one. The percentage of misclassified samples reaches 20% to 30%, but test sets shows good stability.The exploration procedure was applied to the Normetal deposit, where the authors took 160 samples during the summer of 1977. It quickly leads to the definition of targets for more detailed exploration together with a good recognition of the old known deposit.IntroductionVolcanogenic massive sulphide deposits in the Abitibi belt (Quebec) are mainly found in rhyolites or acidic pyroclastics in the uppermost portion of a calc-alkaline volcanic series (Descarreaux, 1972). The deposits are thought to have formed syngenetically by the action of volcanic hydrothermal exhalations during the waning episode of a felsic volcanic cycle (De Rosen Spence, 1976). Alteration pipes of disseminated sulphides are commonly present. Metal deposition from hot springs, initiating convection cells in a submarine environment, may have been the dominant process in ore formation (De Rosen Spence, 1976)."

Jan 1, 1981

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By M. Narita, S. Nakayama, M. Fujihara

Hibi Kyodo Smelting Co., Ltd. was founded in 1968 and celebrated its 50th anniversary in 2018. In 1972, we started producing copper cathode with a production capacity of 84 KTPY. Since the company founding, we have undertaken seven expansion projects, and our current copper-cathode production capacity is 290 KTPY. To increase our production efficiency, two tank houses were converted from Conventional process to ISA process in 2006 and 2014. In another investment, we equipped a continuous glue dosing system, which allowed for strict additive-concentration control, yielded quality improvements and reduced the power-consumption rate. Along with an increase in the production of copper cathode, the amount of impurities eluted from the anode increases. To solve this problem, the chelate-resin purification process that was introduced in 1983 was renovated, and impurities could be recovered more efficiently. In this paper, we report various improvements that have been implemented at the refinery since 2000. INTRODUCTION Tamano Smelter and Refinery of Hibi Kyodo Smelting Co., Ltd., founded in 1968, celebrated the 50th anniversary of its founding in 2018. The Tamano Smelter opened its No. 1 tankhouse in 1972, and began operating No. 2 tankhouse in 1984. Thereafter, with continuous production increases and technical improvements, electrolytic copper production was increased from 84 KTPY to 290 KTPY as shown in Figure 1. Table 1 shows the major operating facilities and operation data in 2017.In this paper, details of equipment introduced to continuously dissolve and add glue, various improvements made to the chelate resin process, enhancements made to the crude Ni sulfate process, and another vibrating screen introduced to the copper slime processing flow in accordance with the expansion of copper production capacity since 2000 are reported.

Jan 1, 2019

By W. W. Beaton

The Coxheath copper mine is situated on the north side of the Coxheath hills and opposite the French Vale, at a distance of about 10 miles southwest of Sydney, Cape Breton county. The deposit was discovered in 1880, and the first work on the property was carried out with local capital. Lacer some Boston men became interested and formed a Company to finance the undertaking. This group operated the mine intermittently for approximately 20 years, spending close to one million dollars on the undertaking. Three shafts were sunk to depths of 110, 190, and 340 feet, and further underground workings to the extent of approximately one-half mile were driven. Also, an extensive surface programme was carried out. in which many test pits and hundreds of feet of trenches were dug, Early in the summer of 1928 the Arno Mines, Limited, optioned the property and immediately started an exploration campaign. A series of trenches were dug along the parallel vein system, and over 4,000 feet of diamond-drilling was done. The results obtained were so encouraging that a mining plant was erected in the fall of chat year and No. 2 shaft was drained. A complete new plant was installed, consisting of one 120 h.p. Fairbanks-Morse Diesel engine, direct connected to a Sullivan angle compound, air compressor; an 80 h .p. Leonard boiler, which supplies power for the 7 by 11 Ingersoll-Rand hoist; and a Sullivan class C steel sharpener and oil furnace. Two 250-gallon Cameron pumps, one operated by steam and the other by air, were placed in the mine so that, in case of a break-down, the mine would not be flooded.

Jan 1, 1930

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By A. Khan

The purpose of this paper is to demonstrate the value of identifying and optimizing throughput constraints by utilizing a Constraint Model. This will be achieved by first understanding the overall concept of Operational Excellence, Continuous Improvement and Theory of Constraints as practiced within Vale Canada Limited. Next, the value of utilizing a Constraint Model is demonstrated by primarily identifying constraints. The applications in utilizing Constraint Models will be demonstrated, including the primary benefit of identifying constraints. The remainder of the paper will focus on how to properly setup a Constraint Model using discrete simulation (regardless of simulation software). Benefits of understanding the severity of constraints and movement of the bottleneck will be recognized. The paper will conclude with the summary of real applications within Vale Canada Limited.

Aug 1, 2013

By J. B. Mawdsley

From the view point of the mining engineer, the square-set method of stoping as practised at Butte, Montana, is one ?of the outstanding features of well conducted mining operations in that camp. The following information was obtained in the course of two months underground work in the Granite Mountain mine, during the summer of 1920, which is one of the properties of the North Butte Mining Company, situated on the well known Speculator vein. Most of the information was derived from personal observation and from discussions with various miners and with members of the staff. Geology The copper mining area of the Butte district is some two miles long by one and a half miles wide, a mineralized area in a great batholith of monzonite granite, locally known as the Boulder batholith. This extensive body of granite is traversed by several series of mineralized fault-fissures which differ in strike but generally dip steeply. Geologists agree that following the formation of the fissures, alkaline solutions ascended and decomposed the felspathic portions of the granite in the immediate vicinity of the fissure walls, and that these alkaline solutions were followed by cupiferous solutions which filled the fissures and replaced the granite next to the walls. A zone of oxidized ore, varying in thickness from 10 to 400 feet, overlies a sulphide zone containing chalcocite, enargite, bornite and chalcopyrite, with a small amount of quartz gangue. The veins are from 3 to 100 feet in width and contain, on the average, 3 per cent of copper, 2 ounces of silver, and 15 cents in gold per ton.

Jan 1, 1925

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016