Search Documents

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993

By G. J. McTeer, D. L. Verhelst, D. J. Rioux

Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training and monitoring.

Jan 1, 2015

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By Alessandro Navarra, Kristian Waters

Mineral concentrators are designed from preliminary geological data, and are therefore subject to geological uncertainty. This uncertainty has a demonstrable impact on the mining lifecycle, and has motivated stochastic strategic mine planning algorithms. The current paper describes how these algorithms may be extended to consider mineral processing operations in conjunction with open-pit mining operations. In particular, the paper describes an effective way to incorporate variable concentrator feed grade into these algorithms, which is the first step toward more elaborate representations of mineral concentrators. The resulting framework will be able to connect geological data to alternate configurations of the downstream resources, hence comparing the benefit of each configuration, and the corresponding capital investments. Sample computations are presented, comparing the NPV and utilization for several different mineral processing capacities.

Jan 1, 2015

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By D. M. Maijer, S. M. Mohseni, A. B. Phillion

The microstructure evolution kinetics of aluminum alloy B206 during artificial aging has been investigated using non-isothermal calorimetry. A combination of differential-scanning calorimetry (DSC) and tensile tests have been utilized to develop an Avrami model to predict the precipitation kinetics as a function of the thermal processing parameters. The Avrami coefficients, found based on a Kissinger analysis, compare well against those reported in the literature for aluminum-copper alloys. The rapid precipitation kinetics predicted by the Avrami model at temperatures higher than 200°C were assessed through a qualitative comparison against hardness measurement results. In contrast to the continuous hardening observed at 150°C, the material softens with continuing heat treatment at 250°C resulting in an overaged state. This can be attributed to the rapid precipitation kinetics at this temperature, leading to the termination of the precipitation-hardening effects at early stages of artificial aging.

Jan 1, 2015

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By Lauri Pesonen

"Although electrical energy use at copper smelters is typically about 15-20% of operational costs, it is something which is not very often analyzed and discussed at a detail level in technical papers and presentations. This paper aims to list different equipment configurations per smelter area and estimate their electrical energy consumptions versus unit of material processed. In addition chosen smelting technology and oxygen enrichment rates affect the overall electricity consumption and therefore some overall guidance is provided for efficiency gains.INTRODUCTION In principle, processing plants, such as copper smelters, require electrical and chemical energy together with some degree of human input to process input materials into desirable output form like metallic copper. From the standpoint of metallurgical plant designers, the thermodynamics of smelting, when it comes to releasing and conserving thermal energy, is sufficiently understood and frequently discussed in the literature in detail, but judging from the quantity of publications, the way how we exactly utilize electrical energy is not. This article is meant to illustrate how electrical energy consumption is distributed among different process units and equipment types at copper smelters using various smelting technologies. In general, typically about 15-20% of operational costs are related to electricity and at locations with high electricity prices the potential savings can be quite significant for the overall profitability of the plant operations. In today’s tight profit margin environment any potential savings are more than welcome. The purpose here is not to promote any certain copper smelting technology, but to open a discussion on how and where we use electrical energy, and how the overall energy use could be lowered with the implementation of newest electric power saving designs and solutions. Using the principles outlined in this article, it should be fairly easy and straightforward to replicate the calculations and even improve them wherever it is seen necessary for the greater benefit for us all in this industry"

Jan 1, 2017

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017