Search Documents

By P. Espinoza, I. Yutronic, J. Olivares

"Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved.Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals.On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs.Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others."

Jan 1, 2012

By Irvine J. Berscheid

This paper describes a rock drill bit which, although conventional in the processes of manufacture and use on the job, has incorporated into the outer wall or periphery of the insert, where wear is always the greatest, a variable amount of extra metal, distributed in units of height of insert to withstand this excessive wear. Explained are variations of construction, how the extra metal enables the bit to drill more footage, prevent antitaper and the need to gauge grind, increase penetration rate and the length of run per regrind, reduce shank breakage and ma-chine costs, and permit increased production per man-shift, without requiring any change in equipment already on the job. F OR purposes of clarity, reference to bits here means integral rods or multi-winged bits which have their inserts sharpened to a conventional shape. When dull, the insert has worn, on its face, a flat which increases in width as we progress from near the center of the bit toward the outer edge. Very

Jan 1, 1965

By S. F. LEAMING

Jade occurs with alpine-1ype serpe111iniIes in a be// of middle Paleozoic to Triassic rocks extending from southern British Columbia in10 Yukon Territory. Most known deposiIs are in BriIish Columbia and are associa1ed wi1h the Cache Creek Group. Jade deposits are generally small len1icular masses 1ha1 lie along con1acIs beIween serpenIinites and various countIy rocks; some are 1ec1onic inclusions wi1hin se1pen1ini1es. Qualify and quan1i1y of 1he jade varies widely. Deposi1s occasionally, but rarely, reach 3,000 /Onnes. The ma1erial may be rendered non-commercial by .frac1ures, impuriIies, inferior colour and poor IexIure. Because unit value of jade can approach $80.00 per kg, greaI incen1ive exisIs 10 exploi1 1his resource. Successful commercial operations, however, depend on large- *A more detailed version of 1hi paper occur in Leaming (1978). PHOTO I . Sawn blocks of nephrite ready for shipping. 270 volume sales, for which $6.00 to $15.00 per kg is more realistic. Many undiscovered jade deposits undoubtedly remain in the Canadian Cordillera.

Jan 1, 1984

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By A. Ockewitz, A. Trondl, D. -Z. Sun

"Numerical simulation of extrusion processes offers an efficient method for tool design and optimization of geometries and properties of extruded parts. However, until now there are few systematic investigations about influences of material model and different parameters e.g. for friction and thermal processes on calculated local and global responses. Since extrusion processes are essentially influenced by friction between billet and extrusion tools, new friction tests were performed in this work to develop a reliable friction model. Compression and torsion tests were performed at different temperatures and velocities to calibrate the material model for extrusion simulations. Extrusion processes for circular rods and U-profiles were conducted at TU Berlin with backward and forward extrusion for different extrusion ratios, billet temperatures, product velocities and cooling conditions. This work focuses on numerical simulations of the extrusion tests with the FE code HyperXtrude. Based on the calculated distributions of local strain, strain rate and temperature the recrystallized volume fraction and grain sizes were calculated with empirical models and compared with the experimental results from optical micrographs and EBSD scans. The calculated total and friction forces and temperatures were compared with the experimental results and the deviations between experiment and simulation were analyzed.INTRODUCTION Extruded aluminum components are widely used in vehicle constructions due to light weight and manufacturing consideration. Local mechanical properties in the components are inhomogeneous as a consequence of the spatial distribution of microstructure which is influenced by numerous factors like material composition, temperature, tool design, friction, extrusion ratio and speed during the extrusion process. For the optimization of the extrusion process with regard to all these factors numerical simulation can be an essential tool. Based on results of finite element simulations of the extrusion process the microstructure in the extruded components can be predicted and then the resulting mechanical properties can be numerically determined instead of by costly trial and error methods. The aim of the work presented in this paper is the development of a numerical method for the simulation of extrusion processes with modeling of microstructure."

Jan 1, 2018

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By J. Malone, D. Loth, J. Palmer

WMC Resources' Kalgoorlie Nickel Smelter was commissioned in 1972 at a design capacity of 30,000 tpa of contained Nickel in matte. A series of upgrades and progressive improvements have resulted in a design capacity increase to 110,000 tpa of contained Nickel in matte. The smelter sources nickel-in-concentrate from three Mine / Concentrators and supplies nickel-in-matte to WMC's Nickel Refinery and export customers. The Flash Furnace was last rebuilt in 1999, and is over halfway through the 10-year campaign target. The many modifications over the previous campaigns, including the Integrated Flash Furnace, are reviewed. Recent operation of the smelter and the development of the process during the current campaign are detailed herein. An overview of key interfaces with the Nickel Business Unit Concentrators and Refinery operations is provided.

Jan 1, 2005

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By G. A. Young

THE Geological Survey was created in 1842 to aid the development of Canada's mineral resources. Although the institution has been in existence for nearly 100 years and has accomplished an immense amount of work, the need for its services remains as great as ever and, indeed, it is difficult to imagine a time when the country will no longer require a Geological Survey. This is so because of the tremendous effort required to make an adequate geological examination of so large an area as is embraced by Canada and partly because what today may seem an adequate geological examination proves, later on, to be inadequate. The ultimate objective of the Geological Survey is to complete the study of all phases of the geology of Canada, that is, to determine how and when the physical features originated, how and when the soils and other unconsolidated deposits were formed, and how and when the solid rocks and associated deposits were produced and assumed their present conditions. When the study has been completed, any only then, will it be possible to make a reliable estimate of the country's mineral resources. This appraisal embraces more than determining the value of already discovered deposits: it also involves attempting to establish what kinds of undiscovered deposits may be present and where they may occur. The estimating of the potential mineral wealth can be clone only after the geology of the country is known. Not until then will it be possible to forecast what types of valued deposits may occur in a district and what types will almost certainly be lacking. A thorough knowledge of the geology of the country is desirable not only to permit estimating the potential mineral resources but also as an aid in locating and developing mineral deposits whether these are of the nature of a bed of limestone, a seam of coal, a reservoir of petroleum, a vein, an irregular body of sulphides, or any other type of deposit.

Jan 1, 1940

By S. Haggarty, R. Walton

Barrick's growth and development plan will add three major new mines during 2005 including the Lagunas Norte Project in the La Libertad Province of Peru, the Veladero Project in the San Juan province of Argentina, and the Tulawaka Mine in north¬western Tanzania. Lagunas Norte and Veladero are similar in that they are both green-field open pit deposits at elevations over 4,000 meters above sea level, with two stage crushing and heap leaching followed by Merrill Crowe zinc precipitation for precious metal recovery. Operating sites will each generate in excess of 700,000 ozs Au per annum with commissioning and full scale operation planned during the third and fourth quarter of 2005. Details with regards to regional geography, development schedule, production and process specifics for Lagunas Norte and Veladero will be discussed in this presentation providing an overview for the respective properties.

Jan 1, 2005

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By I. M. Marshall

A review of technical literature covering Canadian mining emphasizes the advancement and changes that have been made in mining practice. However, current technical publications rarely outline basic principles or state definite rules that govern profitable mine operation. it may be argued that the broad principles of mining have long a go been outlined in various handbooks, text-books, and periodicals, and that these principles never alter. This is in great part true, but modern machinery, improved meta1-lurgical practice, and other advances, have in part modified these principles or changed the manner of their application. Many engineers hesitate to state specific rules, because it is so easy to quote an exception to a rules that any such statement appears to lose weight upon its very utterance. The exception to rules, and the reluctance to formulate rules, has forced such maxims as "the only rule in mining is the point of a pick," and "gold is where you find it". As an illustration of rules and their exceptions, one might quote the time-honoured maxim that a mill should not be built before a shaft has been sunk on a property in point of fact, Canadian mining history is replete with examples of wasted capital where a mill was built before a shaft had been bottomed. Y et this past year has seen a property enter profitable production whereon the building of the mill was started before the shaft was sunk. Instances such as this should not be accepted as evidence that a rule has been overthrown, but rather as an exception to the rule. The case cited pays tribute to the application of the diamond-drill combined with the correlation of sound geology. Incidentally, both these features emphasize a modern trend in the development of Canadian mining properties-a trend that is perhaps worthy of further comment. It is such trends that affect the principles of mining or modify their application. It is with such that this paper deals, at ]east in part. It is hoped that the statement of principles and the opinions herein outlined will be of sufficient interest to arouse discussion.

Jan 1, 1939

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By D. C. Fraser

"Geophysical Engineering and Surveys Limited of the Keevil Mining Group have routinely conducted ground surveys with VLF-EM receivers for the past two years. Both Crone's Radem and Ronka's EM16 have been used.VLF-EM dip-angle data often yield complex patterns which require considerable study for a proper interpretation. A method was developed which allows field operators to transform the noncontourable dip angles into contourable data, producing conductor patterns which are immediately apparent to exploration personnel untrained in VLF-EM interpretation.VLF-EM contoured data generally peak very close to the top of a conductor, thereby allowing drill holes to be spotted accurately. However, the data generally should not be used alone to select drill targets because structures may be sufficiently conductive to yield strong anomalies. Thus, magnetic and/or vertical-loop EM correlations may be considered as necessary criteria for drilling.VLF-EM surveys can replace IP surveys in certain environments. For example, the Restigouche orebody in the Bathurst camp of New Brunswick yielded a VLF-EM anomaly as distinct as that obtained by IP, although the body did not respond to vertical-or horizontal-loop EM. However, the cupriferous breccia pipes of the Triba mine near Batchawana, Ontario yield strong IP anomalies but not VLF-EM anomalies, illustrating that disseminated ore targets should be sought with IP rather than with VLF-EM."

Jan 1, 1971

By R. P. Smith

PRIOR to June, 1937, the employees of Hollinger Consolidated Gold Mines, Ltd., at Timmins, Ontario, received medical care for themselves under a contract system developed through an agreement between the employer, employee, and a contract physician. This form of practice is common to the mining industry in Ontario. But with the improvement in mining methods and conditions of living, and through an increasing demand for provision of a complete medical care, it was not any surprise when the employees of the Hollinger mine approached organized medicine and indicated their desire for a plan to provide their families with a more or less complete medical service in addition to that supplied for themselves. In April, 1937, this approach was made, and on June 18th, 1937, the Hollinger Employees' Medical Services Association was formed and started to provide medical services. A review of five years' experience is now presented. The Association provides complete medical service for the employee, his wife and family, as well as those dependents who are the total responsibility of the employee. The employee membership is limited to employees at the Hollinger mine in Timmins who reside in the immediate vicinity. The employee is examined by a Company doctor on application for employment and is subject to further examination by a specialise in chest diseases under the direction of the Workmen's Compensation Board of Ontario. The wife and family are not subject to examination but have to be registered when the employee is accepted for employment. The dependents, other than the immediate family, are subject to medical examination and approval after the employee has applied for such dependent or dependents to be admitted. Membership in the Association is obligatory when the employee is hired, but at the end of any Association year he may drop out if he so wishes.

Jan 1, 1943