Search Documents

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By Victor Rudenno

"Previous methods have employed statistical analysis to model future mineral resources. The method presented in this paper uses Zipj's Law to determine the size and grade of tin deposits still to be discovered. The law is applied independently to both known deposit tonnage and grades. A probability distribution for both 'tonnage and grade is computed/or those deposits still to be located and then, by applying a correlation between tonnage and grade, a distribution of the probability of metal content discovery is obtained.By considering an economic cut-off in metal contained in a deposit, the probability of economic success for the next tin discovery is computed, both for a world discovery and for the special case of Tasmania, Australia. The results indicate a probability of 11-37% on a world-wide basis and 18% chance of economic success in Tasmania.IntroductionIn the past , most attempts to determine the probability of success in finding an economic mineral deposit have relied on the accumulation of statistical data. These data are then used to predict a suitable frequency distribution to assess the probability of finding a deposit of a given size and grade (Singer,1975).The method not only relies on one having sufficient data, but also on the assumption that the data are not biased and that the distribution (usually log-normal) is a correct one. The method presented in this paper, to analyze tin deposits, uses Zipf's Law, which has been recently applied to oil, uranium, lead-zinc and gold deposits by Folinsbee (1977) and to Western Australian gold deposits by Rowlands and Sampey (1977). Tapp and Koniuszko (1978) have applied Zipf's Law to mineral distribution patterns in the Northern Australian orogenic provinces, which has enabled them to make predictions with a relatively small data source."

Jan 1, 1981

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By S. Yadav, T. G. Murthy, C. Saldana

"An experimental study has been carried out in order to study the deformation of porous brittle materials under plane strain indentation. Gypsum, which is well known model system for understanding the behaviour of soft rocks, is used in this study. The effect of wedge angle is investigated in this research through this series of experiments, using wedges of 3 different apical angles. High-speed, high-resolution images are captured using a CMOS camera during the experiment. The images obtained are analyzed using a Particle Image Velocimetry (PIV) algorithm in order to obtain the evolving velocity, strain-rate and strain fields.INTRODUCTIONThe problem of indentation, which is usually referred to in the context of hardness testing is ubiquitous as a material characterization technique for a large class of solids. Mechanical properties of materials such as yield stress, flow stress, fracture toughness, elastic moduli etc. can be related to the hardness of a given solid. The indentation problem involves a given material or solid (whose properties are to be determined) indented by a relatively harder material (indenter) allowing the solid to undergo plastic deformation, which is then related to the yield stress of the material. The problem of indentation and its variants see many applications ranging from mining and petroleum industry, infrastructure industry, manufacturing, and biomedical sectors. Indentation has been extensively studied in metals, with accurate measurement of deformation parameters, stresses and comparison with analytical solutions. On the other hand, understanding of indentation in other class of solids such as cellular solids, porous solids, rocks, and soft solids is still nascent. In case of rocks, a comprehensive understanding of the indentation problem is very crucial because of the obvious applications in mining, petroleum and infrastructure sectors. The inherent porosity, the brittle nature of the rocks, adds to the complexity of indentation in these porous brittle solids. Various theoretical models with degrees of simplifying assumptions have been proposed to study the indentation in rocks. The most common model used in the study of indentation in rocks is a cavity expansion model, wherein a blunt indenter indenting into a rock is approximated with the expansion of cylindrical or spherical cavity in an elastic-plastic material. Complementary studies in understanding fracture initiation and propagation due to indentation has been largely based on the studies of traditional brittle materials such as glass."

Jan 1, 2015

By S. Makni, G. Gagnon, F. Couët, C. Rochefort

"Comminution represents a significant part of mineral processing plant operating costs. Yet, autogenous (AG) or semi-autogenous grinding mills (SAG) are difficult to control because of disturbances like feed size distribution and rock hardness. AMIRA, within project GeMIII, developed a comminution index from laboratory crusher data. The index correlated with the Bond ball mill work index and with the A×b parameter. The present work extends the use of crusher data as a grindability indicator to real-time industrial applications. The aim is to improve comminution operation using online hardness estimation. Because the operational work index is proportional to the ore work index, rock hardness variations can be estimated from the feed and product size distributions, the throughput, and the power draw of a crusher. Real-time estimation of rock hardness can help understand the dynamic behavior of AG and SAG mills. Multivariate time series were analyzed to understand the impact of hardness on a SAG operation. Results showed that the estimated hardness influences the SAG operation and its throughput. Moreover, non-linear dimension reduction was used to ease the process visualisation and search for potential control strategies. In the future, online hardness measurements should also impact the understanding of comminution circuits and improve their operation.INTRODUCTIONThe variability in hardness, and the feed size distribution, are two of the main disturbances affecting comminution circuits (Sbarbaro & del Vilar, 2010). Size distribution can be measured by imagebased granulometry systems such as WipFrag (Maerz, Palangio, & Franklin, 1996), or by 3D vision systems when the fines are difficult to discriminate by 2D segmentation (Faucher, Makni, Gagnon, Lavoie, & Roberge, 2015).There are few examples of online hardness measurements. One example was the work of Casali et al. (2001) who developed a hardness indicator. The ore grindability soft sensor used the fraction of each lithological class in the ore, as determined by image analysis, to predict the work index of the material. The model was developed using a moving window with a width of 12 months and trends were shown over many years with one data point per month."

Jan 1, 2016

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By M. A. Vos

"Aggregates are the low-cost mineral raw material of building construction. Large volumes of aggregate are consumed each year. The availability of aggregates in southern Ontario is discussed in the context of the geological formations in which they occur. Sand and gravel are abundant in glacial deposits and in recent sediments. A knowledge of the glacial history is important for their discovery. Bedrock formations provide a variety of aggregates in Ontario. Knowledge of the rock types involved and of the depth of overburden are important for evaluation of the aggregate potential of bedrock resources in an area. Utilization of available resources intensifies as the population increases. Urban development makes it progressively more difficult to satisfy the demands of the construction industry. The effects of urban development on the aggregate resource base of an area are illustrated by developments and consumption statistics in the Toronto- centred region. There is an obvious need for a comprehensive survey of available resources in urban areas to serve as a guide in land-use planning. To fill this need, staff members of the Industrial Minerals Section, Geological Branch, Ontario Department of Mines and Northern Affairs, are engaged in mapping projects and mineral resource studies in southern Ontario as well as in some urban areas of northern Ontario."

Jan 1, 1972

By Yve Aymong

"The objective of this paper is to help readers benefit from the practical experience of persons who have been engaged for several year s in the testing and repair of power transformers. Power transformers are known to be reliable pieces of equipment with expected usage of 25 to 30 years, but simple problems such as leaking radiators, or a bad contact on a tap changer, could shorten the life of a transformer. To ensure a longer life span, transformers should be checked on a regular basis.What is a Power Transformer?It can be a 90 MVA transformer for Hydro-Québec or a power transformer can be a 500 KVA unit in a small hospital. Generally a power transformer is an oil -filled type of 3 to 5 MVA. It can also be a dry type transformer, that should be treated in the same manner as oil-filled transformers, and some of the tests explained in this paper also apply."

Jan 1, 1984

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By J. L. Blaylock

Normally, the hydraulic system and structures are considered to be unrelated items. In reality, the two cannot be separated because one affects and depends on the other to function properly. This paper explores the potential failure areas of hydraulic cylinders, and suggests possible methods to prevent failures from occurring. The use of high-strength low-alloy steel in frames is reviewed and the benefits discussed. Fabrication techniques and handling of material are noted in the hope that this knowledge will aid in the repair of frames in the field.

Jan 1, 1979