Search Documents

By L. Gawlik

Since the beginning of the 20th century, coal has been the world?s main source of primary energy. In the last few decades, consumption of coal has gradually decreased in some European countries and elsewhere due to the introduction of other energy sources. Regardless, industry continues to use solid fuels for energy production despite of their association with carbon dioxide emissions (about 7 billion Mg). For global development going forward, it is important to estimate what level of energy consumption can be expected as far into the future as the next few decades. To answer this question, specialized global institutions such as the International Energy Agency, the World Energy Council, the World Coal Institute, the U.S. Energy Information Administration, the International Institute for Applied Systems Analysis, as well as oil companies (BP, Shell), conduct periodic forecasts of world energy consumption. The development of such forecasts is very complex because their reliability is influenced by many factors that are difficult to estimate, such as economic development, population growth, climate change, and public awareness. We are all aware that the global demand for electricity will rise significantly in the coming years as a result of anticipated population growth, industrial development, rising living standards, and the general development of civilization. The world?s mineable resources in 2010 were as follows: coal 665.6 million Mg, brown coal 195.4 billion Mg, oil 163 million Mg, and natural gas 185.5 billion m3. The annual global primary energy demand in 2008 was more than 12 billion toe (12,267 Mtoe). In 2006, electricity production in the world amounted to 18,921 TW?h. The structure of the primary energy mix in TW?h (2006) was as follows: coal 41.0%; natural gas 20.1%; nuclear fuel 14.8%; hydro energy 16.0%; liquid fuels 5.8%; and other renewable energy sources 2.3%. The European Union (EU) is one of the largest coal consumers in the world. In 2010, the EU-27 produced 396.1 million Mg of brown coal, and 132.9 million Mg of hard coal; 188 million Mg of coal was imported from outside the EU. The largest hard coal producers in the EU-27 are Poland, Great Britain, Germany, the Czech Republic, and Spain; major brown coal producers are Germany, Greece, Poland, the Czech Republic, and Hungary. For many years, the Polish energy sector has been based on domestic fuel sources ? hard coal and brown coal. The characteristic feature of the Polish balance of primary energy resources is a very high share of coal ? much higher than the world average. Pursuing the decarbonisation of the Polish economy may jeopardize Poland?s energy security, leading to a significant increase in electricity prices, which would hamper the country?s economic development. Price volatility and supply uncertainty are now the dominant features of the international markets for oil and natural gas. The high share of these fuels in meeting energy needs is the reason for unrest in many countries, including those in the EU. Under these circumstances, coal may become the stabilizing element of EU energy security.

Aug 1, 2013

By Antonio Laguna

During the past few years, synthetic efforts have been addressed to the synthesis of polymeric materials with optical or semiconducting properties or even with capabilities to act as sensors for volatile organic compounds (1). The most recent studies have been concerned with the synthesis of heterometallic systems with short metal-metal interactions and the determination of their optical properties. These complexes are undoubtly interesting from a theoretical viewpoint and include an emerging class of luminescent materials, in which the observed luminescence results mainly from the interactions among the different metal centers, as well as the environments of these atoms. The understanding of the photophysics and photochemistry of these products could permit the design of complexes with appropriate metals and ligands chosen for individual applications. Following a synthetic strategy consisting on reactions between acid heterometal complexes and basic gold precursors we have succeded in synthesizing supramolecular assemblies formed via acid-base stacking, which display tunable luminescence or selective and reversible sensitivity to Vapour Organic Compounds (VOC?s) (2-5). In this sense, in accord with previous Mössbauer studies carried out in the gold precursor complex [AuR2]- (R = C6F5), the basic properties of this and related materials have been employed as building blocks of supramolecular assemblies in their reactions with complexes in wich the metallic centers act as lewis acids as, for instance, Tl(I) or Ag(I) (6). For instance, in the case of silver, by reacting equimolecular quantities of [NBu4][Au(C6F5)2] with AgClO4, in acetone, a solid of stoichiometry [Au2Ag2(C6F5)4(OCMe2)2]n is obtained. The polymeric nature of this material in solid state is confirmed through X-ray analyses (figure 1). It consists of polymeric chains formed by repetition of Au2Ag2 moieties linked through short gold-gold interactions. Nevertheless, in solution, the nature of this polymeric materials was still a matter of controversy and, in this case, the optical properties have been shown as useful tools in order to obtain information. Thus, while dilute acetone solutions of this complex give a emission coming from pentafluorphenyl localized ??* excited states, in accord with the presence of isolated tetranuclear Au2Ag2 units, when the measurements are done at different and higher concentrations, a band that does not obey the Lambert-Beer law appears. This deviation is consistent with molecular aggregation in solution of these units through gold-gold interactions, and a clear correlation between the emssion wavelength and the structure in the solid state and in solution is shown (figure 2). DFT calculations accord with the observed experimental behaviour and show the nature of the orbitals involved in each transition.

Oct 1, 2003

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By A. Miura, R. Winarko, D. B. Dreisinger

Chalcopyrite leaching in acidic ferric sulfate media at ambient temperature exhibits slow kinetics and poor leaching efficiency, which is typically attributed to surface passivation. Recently, the presence of small amounts of iodide in the leaching media has been reported to significantly accelerate chalcopyrite dissolution. To further explore the behavior of chalcopyrite leaching in the presence of iodide, it is essential to determine the factors that control the leaching kinetics. In this study, we investigated the effect of initial solution potential, iodide concentration, particle size, and temperature on the kinetics of copper extraction from chalcopyrite. The key in the experimental setup was to minimize iodide loss by iodine evaporation and precipitation as cuprous iodide. The former was achieved by performing the leaching tests in fully sealed leaching systems. The latter was achieved by maintaining the solution potential higher than 420 mV (versus Ag/AgCl electrode), where formation of CuI precipitate is possible. The experimental results show that higher solution potential and higher iodide concentration had a pronounced positive effect on the rate of chalcopyrite dissolution. There was no effect associated with particle size, which might be due to the narrow size range tested. The positive effect of increasing temperature only manifested itself when the solution potential was sufficiently high. INTRODUCTION The main challenge of chalcopyrite leaching using ferric ions as the oxidant at ambient temperature is the slow kinetics and poor extraction. The reason for this leaching behavior has been attributed to passivation resulting from formation of insoluble passivating layers on chalcopyrite surfaces, which could be metal-deficient sulfides, elemental sulfur, polysulfides, and iron precipitates (Klauber, 2008). To overcome passivation, technologies using higher temperature and pressure have been developed to leach chalcopyrite concentrates, such as the CESL process (Mayhew, McCoy, Mean, & Woeller, 2013), FLSmidth Rapid Oxidative Leach (ROL) process (Mulligan et al., 2017), Galvanox (Dixon, Mayne, & Baxter, 2008), Albion process (Hourn, Turner, & Hourn, 2012), HydroCopper (Hyvärinen & Hämäläinen, 2005), TPOX (Dreisinger, 2006), and AAC/UBC process (Dreisinger, Dempsey, Steyl, Sole, & Gnoinski, 2003). Even though they are effective in accelerating copper leaching kinetics, those technologies typically have higher capital and operating costs associated with production of concentrates and application of autoclaves. This makes them unsuitable for treating low grade primary copper sulfide ores.

Jan 1, 2019

By Zia Pirzada

"Time is of the essence" and "Time is money" These are powerful and true statements during a project life cycle and have far-reaching implications on the success and failure of the project Time and progress management is crucial to the project success. Project delays may increase the cost to an unacceptable level and may render the project as economically unfeasible. On the other hand, if the project is completed on time or earlier than as planned, it may generate economic benefits greater than what had been envisioned To take advantage of the financial opportunities and to improve the cash flow as well as Return On Investment (POI), project schedule can be accelerated to complete the project earlier than planned Project schedule acceleration can be achieved by using analytical tools, such as "Schedule Optimization", "Schedule Reduction", "Schedule Compression" or a combination of any of these concepts along with the "Planning for start up". Schedule optimization does not entail any extra cost, however, other acceleration methods, such as Schedule Reduction and Schedule Compression, may require extra expenditures from the owner. Based on the forecasted early start of the revenue stream, the extra expenditure could become a worthwhile venture with a very high rate of return To accelerate the schedule, all aspects of the project should be reviewed with acceleration costs calculated. All risks and opportunities should be evaluated and taken into consideration to determine if the acceleration is feasible and advisable and will provide definite financial advantages Sometimes schedule acceleration may be desired to prevent the company from paying liquidated damages. This is especially true when the project is not expected to complete on the contractual completion date and when the cost of acceleration is less than the liquidated damages that may accrue against the company.

Oct 1, 2010

By Laxman M. Amaratunga

"The fine fraction of tailings is usually excluded from the backfill process and generally disposed on the surface in tailings ponds. Because of the ever increasing demand for fine grinding in the extraction process for improved liberation of valuables in the ore, increased production of fines in the tailings has resulted. The negative impact of surface impoundment of tailings on the environment is well known. Amaratunga and Annor (1989) first presented a concept of fine tailings agglomeration for backfill.This paper presents the development of the novel cold-bond tailings agglomeration (CBTA) technology for non-reactive fine gold mill tailings. For cold-bond agglomeration regular portland cement was used as a binder. In order to cut costs, alternate binders such as lime, and blast furnace slag cement were examined. The effects of binder dosage, curing time, and agglomerate size on the fracture load strength of the agglomerate were studied.Fine tailings agglomerates are mixed with coarse tailings or non-agglomerated fine tailings to make high density fill compositions to be used as underground backfill. Alternatively, the agglomerates can be used as aggregates for surface applications. The paper discusses the environmental and operational benefits of this total tailings utilization and disposal technology.IntroductionIn Canadian mines, mill tailings are probably the most commonly used material for backfill. However, only the coarse fraction of tailings is desirable for use as hydraulic fill or high density fills. The fines are disposed on the surface in tailings ponds since they are unsuitable for underground backfilling owing to the following factors:i) slow settling ratesii) longer percolation timeiii) excessive consumption of binder due to drainageiv) poor compactionFor improved value liberation more milling operations have resolved to fine grinding in their comminution circuits. Gold milling operations driven by down stream leaching processes grind their ores excessively fine. In general, gold mines use hardly any tailings for backfilling. This can result in periodic short falls and the need to search for alternate backfill material from other sources. Apparently, the gold producers are the most identifiable sector which suffer from a shortage of backfill materials ( Amaratunga and Annor, 1989)."

Jan 1, 1994

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By J. Shen

Direct methanol fuel cells have been the subject of considerable research in the last decade. Performance levels realized in cells, stacks, and systems show that this technology is a promising power source for a wide range of portable applications. A direct methanol fuel cell (DMFC) operates directly on a methanol fuel stream typically supplied as a methanol/water vapour or as an aqueous methanol solution in liquid feed DMFCs. The fuel streams in DMFCs are usually recirculated in order to remove carbon dioxide and to re-use the diluent and any unreacted fuel in the depleted fuel stream exiting the DMFC. The concentration of methanol in the fuel circulation loop is an important operating parameter because it determines the electrical performance and efficiency of the direct methanol fuel cell system. The methanol concentration in the circulating fuel stream is usually measured continuously with a suitable sensor, and fresh methanol is admitted in accordance with the signal from the sensor. There are many factors to consider in developing a methanol sensor suitable for DMFCs. These factors include sensitivity, cost, size, simplicity, reliability, longevity, concentration range, and dynamic response. In particular, reliability and low cost should be addressed. Methanol concentration sensors measure methanol concentration by means of detecting the variations of physical/chemical properties of the solution. In this work, methanol concentration sensors based on electrochemistry, electric-capacitance measurement, infrared sensing, ultrasound sensing, and other techniques are reviewed to discuss their advantages and disadvantages.

Jan 1, 2005

By M. K. Aly

"ABSTRACTThis paper briefly describes the mining method proposed for the iron ore deposits in Wadi Shatti, western Libya. The iron ore produced will be used in the steel plant at Misurata on the Mediterranean coast. GeologyThe Wadi Shatti is located in the central part of western Libya. Flat iron-bearing sedimentary rocks are exposed with remarkable regularity in this valley. It occupies an area 200 km long by approximately 20 km wide trending in an eastnortheast direction between Jabal Fazzan in the north and Zel1af Sand Dunes in the south (Fig. I). Only a part of this valley has been ful1y explored by drilling on a 400- by 200-m pattern in an area of 18 km2 south of the town of Taroot. Farther to the south, no exploration by drilling can be done due to the presence of sand dunes .The iron-bearing bed is about 10to 15m thick, with a dip of 2 to 4 degrees in a southerly direction . The overburden consists mainly of clayey sandstones, 4 to 5 m thick, in the northern part, increasing to 35 m in the southern part. The iron ore bed consists of three different layers, from the floor upward: (1) Lower Reduced Ore (LRO), having a varying thickness of 1 to 7 m; (2) Magnetic Ore (MO), with a thickness varying from 4 to 12 m mainly in the central part of the area; and(3) Upper Reduced Ore (URO), with a bed thickness varying from 0 to 7 m."

Jan 1, 1980

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By R. W. Lawrence

Sulphide is an effective reagent in the precipitation of base metals for both metal winning and environmental control. BioteQ Environmental Technologies Inc. has successfully demonstrated in industrial plants that biogenic sulphide reagent can be generated cost effectively and used to win metals such as copper, zinc and nickel from low-grade leach solutions and wastewater. Commercial plants in which sulphide reagent is used to produce high quality treated effluents for discharge directly to the environment are also in operation. Operations utilizing biogenic sulphide reagent for copper recovery from acid drainage and low grade leach solutions are discussed, including those at Bisbee, Arizona, commissioned in 2004 and at the Dexing mine in China, scheduled for commissioning in 2007. In addition, a new application of BioteQ's technology for the recovery of copper from gold-cyanide solutions, and the regeneration of cyanide, utilizing biogenic sulphide in place of chemical sulphide reagents in the SART process is described.

Jan 1, 2007

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By C. A. Petch

Abstract - The High Lake polymetallic deposit is located in the northern Slave province, 40 km south of Coronation Gulf, Nunavut. The main zone, the AB zone, hosts an estimated resource of 3.56 Mt grading 5.0% copper, 1.1% zinc, 0.06% lead, 1.7 g/t gold, and 18.2 g/t silver. Archean felsic metavolcanic and metavolcaniclastic rocks are the dominant rock type and are associated with lesser mafic metavolcanic and carbonate-rich metasedimentary rocks. The sequence strikes north-northeast, dips steeply to the west, and is truncated to the west by a large granodioritic intrusion. The mineralization at the AB zone is comprised of massive and stringer chalcopyrite-sphalerite-pyrrhotitepyrite± galena. At the core of the mineralized zone, intensely chlorite-altered rocks are locally metamorphosed to form distinctive zones of anthophyllite-magnetite-cordierite-altered rock. Peripheral to the mineralized core, alteration consists of sericitization, silicification, and weaker chloritization. Primary morphology and facing direction of the zone are difficult to interpret in part due to poor primary metal zonation of the deposit. However, the irregular shape of the mineralized zone and the erratic zones of zinc enrichment at the fringes are consistent with the interpretation that the zone was formed by the replacement of a porous volcaniclastic pile.

Jan 1, 2004

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of&apos; motors, and motor and equipment bearings. With today&apos;s digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system&apos;s performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By P. Erskine

"Hyperaccumulator plants can be utilized as ‘metal crops’ in agromining operations. This emerging technology produces ‘bio-ore’ by growing ‘metal crops’ on sub-economic ore materials, such as natural ultramafic soils. In a typical application plant material is periodically harvested, followed by air-drying and incineration to produce the bio-ore intermediate. The bio-ore is of very high grade (>15 wt. % nickel), and of high purity, and may be processed into a number of different products (including nickel metal, nickelbased catalysts and pure nickel salts). Current research efforts from our team focus on Mediterranean climate field trials (Albania, Spain) and tropical climate field trials (Malaysia, Indonesia). Field-scale demonstrations are required to provide evidence of real-life performance and of economic viability. If the trials are successful, agromining may in the near future support local livelihoods with income opportunities as an alternative type of agriculture: to farm nickel.INTRODUCTION AND BACKGROUNDHyperaccumulators, plants with the exceptional ability to uptake and concentrate trace elements in their shoots, can be utilized as ‘metal crops’ in agromining operations (Van der Ent et al., 2013a; Chaney et al., 1998; 2007; Baker et al., 2010). Agromining produces ‘bio-ore’ from harvested ‘metal crops’ grown on unconventional resources such as natural ultramafic soils (Van der Ent et al., 2015a). The bio-ore is a high purity and very high-grade (>15 wt. % nickel) product intermediate that may be turned into a range of different nickel products (nickel metal, nickel-based catalysts and pure nickel salts). The potential for agromining is greatest in tropical regions (Asia-Pacific Region: Indonesia, Malaysia, Philippines, Papua New Guinea and New Caledonia) where very large expanses of ultramafic soils exist (Van der Ent et al., 2013b). Agromine operations may replace existing marginal agriculture on poor ultramafic soils, for example oil palm plantations that require high fertilizer inputs to be profitable, or take place under a cocropping regime. The ability of ‘metal crops’ to achieve high nickel concentrations in biomass (and hence in harvested bio-ore) from soils with just <0.5 wt. % nickel, makes it possible to access non-conventional resources, not accessible by traditional mining techniques. For example, agromining could be implemented both on the large ‘halo’ around the mine leases, and as part of the progressive rehabilitation process after conventional resource extraction. As with all methods for resource extraction, agromining will be finite due to the diminishing concentrations of nickel in the zone accessible by plant roots (Chaney et al., 2014). Nevertheless, considering soil materials with 0.2 wt. % nickel and ‘metal crops’ with a yield of 100 kg nickel ha-1 the agromining venture may be sustainable for decades (Van der Ent et al., 2015a)."

Jan 1, 2016