Search Documents

By K. A. Hughes

Under the oxidizing conditions of the McClean Lake Tailings Management Facility (TMF) hydrocarbons entrained on the surface of tailings material from mill processes are gradually converted to soluble bicarbonate ion. This has been observed to be a process occurring over approximately three years likely encouraged by the presence of a microbiological community within the tailings mass and in the water column. A recent tailings sampling campaign has provided evidence that bicarbonate ion is participating in the conversion of gypsum to calcite. In older tailings, equilibrium with calcite appears to be controlling the terminal bicarbonate ion concentration.

Aug 1, 2010

By H. Zniber El Mouhabbis

Ore dilution or stope overbreak increases the cost of production and ultimately reduces the profitability of a mining operation. The adverse economic impact of ore dilution is due to the added costs associated with the mucking, haulage, crushing, hoisting, milling, and treatment of waste rock or low grade ore in the hangingwall and footwall. One factor that could have a significant influence on stope overbreak is the undercutting of the stope into the walls. Undercutting stope walls is often necessary, in particular in narrow vein mines. Moreover, equipment size has a role in drift sizing where stope undercutting may become a must in order to fit the mobile equipment while respecting legal clearances.

May 1, 2009

By J. W. Merks

"The accuracy of a measurement on minerals and ores can be assured by applying suitable and unbiased procedures but its precision is a function of the number of primary increments and their mass, the number of lots per consignment or samples per shift, and the number of measurements on analysis fine samples.Experimental data will be used to show how the variance components for sampling, sample preparation and analysis contribute to the total variance on which precision statements for the final measurement are based. This type of experiment should not only form part of quality control programs at mines and smelters, but also underly the criteria on which the design of manual sampling regimes and mechanical sampling systems for bulk solids and slurries should be based.Sampling systems and regimes can only be adjusted and optimized if the variance component for each step in a quality evaluation process is measured. Knowledge of precision characteristics lies at the core of effective loss prevention and control programs."

Jan 1, 1985

By F. Parada L

Two copper concentrate with medium and high enargite content were leached in a 3 L autoclave reactor under conditions based on the CESL process. Copper, arsenic, sulfur and iron were checked in all the experiments and antimony, zinc and molybdenum were evaluated in selected tests. The 98% of the obtained copper extraction is agree with others authors, but the behavior of arsenic, iron an sulfur have some differences. The solid residue was characterized by chemical analysis, DRX and QEMSCAN®. Finally a comparative analysis with neutral roasting as an option for the treatment of this concentrate is done.

Jan 1, 2014

By Sheila E. Daniel

"Since 1989, the Mine Environmental Neutral Drainage Program (MEND) has sponsored research into ways of reducing the environmental impact and financial liabilities associated with Acid Mine Drainage from tailings and waste rock. Toward this overall objective, Kilborn was contracted to review the use and applicability of passive treatment systems for acid mine drainage.Experimentation using passive systems to treat acid mine drainage has been ongoing since the early 1980's in North America. Passive treatments are generally considered an attractive alternative to active lime treatment, since they require minimal human involvement, no power, and only seasonal or periodic care and maintenance after establishment. Most attractive is that initial capital cost to implement a passive treatement system is generally low to moderate. Ongoing operating costs are similarly low when compared to active treatment systems.Passive treatment systems currently used, or under investigation to treat acid mine drainage include: anoxic limestone drains, aerobic wetlands, reed bed wetlands, compost wetlands, microbial systems and bioabsorption systems. These wastewater treatment systems utilize the chemical, biological and physical removal processes that occur naturally in the environment to improve wastewater quality, including: oxidation, reduction, coagulation, adsorption, absorption and precipitation; microbial activity; and, gravity aeration and dilution. The rates at which these processes occur determines the loading which can be treated and the effectiveness of the system.The results of our literature review will be summarized, and insight provided into the applicability of passive systems to treat acid mine drainage from Canadian Mines."

Jan 1, 1995

By Alan S. Lock

Large scale feasibility studies for the establishment of oil-seed and cellulose producing crops on mine tailings have been successfully conducted over 1 growing season with the purpose of these crops to be used as feedstock to the biofuels industry. An acid sulphide tailings impoundment in Copper Cliff, Ontario and a near neutral pH goldmine tailings impoundment in Timmins, Ontario were both tested by amending half hectare plots to approximately 1 m thick with residual biosolids from the pulp and paper industry and growing canola and corn on these plots. Full scale agricultural equipment was used to cultivate seed and harvest the plots to prove the full scale feasibility of farming on these biosolids. The vegetation development, growth, yield, quality and composition were assessed to identify the best species that would maximize biomass development for feedstock to the biofuels industry and carbon credits for the mining industry. Groundwater, biosolids and tailings chemistries were investigated to identify potential deleterious impacts of degrading organic matter on tailings metal mobility. Preliminary hydrologic investigations using moisture sensor profiles elucidate potential conservation of water in amended plots. Tailings amended with biosolids have the potential to provide the mining industry with carbon credits and supply feedstock to this new industry while reclaiming brownfields to a new level, utilizing industrial and municipal organic waste material.

May 1, 2009

By Yongqiang Liu

Background For refractory gold ores with high carbonate contents ! Acid pressure oxidation ! High acid consumption (if low sulfur content) ! Low oxidation efficiency due to CO2 in autoclave ! Problems with slimy precipitates (gypsum, etc.) ! Alkaline pressure oxidation ! Difficulty in fixing arsenic ! Low gold dissolution due to iron hydroxides/oxides coating ! High reagent costs Summary ! Carbonate and sulfide minerals had similar floatability across the pH range tested (5 - 12) using sodium oleate as a collector; ! Thioglycollic acid or citric acid depressed the flotation of pyrite but could not depress chalcopyrite when used alone; ! Combination of thioglycollic acid and citric acid had a much stronger depressive effect, and the mixture depressed chalcopyrite as well as pyrite between pH 8 and 11 without affecting the flotation of calcite and dolomite; ! Calcite could be separated from chalcopyrite and pyrite; dolomite could be separated from pyrite but not from chalcopyrite under the tested conditions.

Apr 1, 2005

By I. H. Redeker

North Carolina is the leading state in the USA in feldspar, mica, and spodumene production. Mixed feldspar, spodumene, mica and quartz are mined from hard rock, open pit deposits and recovered by flotation from the fresh pegmatite type ores. Potash feldspar, mica, clay and quartz are recovered from weathered decomposed pegmatites. The North Carolina State University has a Minerals Research Laboratory in Asheville with trained personnel and flexible pilot plant equipment. The flowsheets for the feldspar, spodumene and mica producing companies and for large phosphate and glass sand flotation plants were developed and tested in Asheville. Examples and problems of pegmatite flotation are demonstrated with flowsheets and slides.

Jan 1, 1981

By Min-Yuan Cheng

Landslides not only cause interruption of road traffic but also cause damage to passing by vehicles and injure people in Taiwan. Due to the budget limitation of government, the overall assessments and maintenance of all road slops cannot be fulfilled. Priority of road for maintenance is a crucial task for road maintenance department to identify. The purposes of this research are to develop an assessment method for the landslide risk and to make strategies to maintain or repair the slopes along mountain roads. To aim both needs to take into account the environmental conditions of the slopes, the engineering measures for stabilizing road slopes, the transportation issues, and the human concerns when dealing with the slopes maintenance along the mountain roads. This study firstly establishes the Landslides Damage Risk Evaluation Model (LDREM) to calculate the risk of slope failure, considering the probability of landslides, temporal probability, spatial impact probability, the value of human life, transportation time increased, and travel cost due to detour etc., and then the loss of life and transportation can be calculated. Secondly, based on the value of risk and the risk evaluation, considering the risk acceptance criteria for loss of life could provide assistance for road maintenance department to determine the priority of mountain roads for maintenance.

Aug 1, 2013

By John Monhemius

Looking back over the past half century, it can be seen that the growth in the importance of hydrometallurgy for the production of non-ferrous and precious metals almost exactly parallels the rise of the environmental movement and its principal NGOs, such as Greenpeace and Friends of the Earth. The paper will review important landmarks in the development of the science and technology of hydrometallurgy and show how many of these have been influenced by pressures on the industry brought about by environmentalists. Successful innovations as well as commercial failures will be considered and reasons for the success or failure will be analysed and lessons drawn to guide future developments.

Jan 1, 2014

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

By Anna Maria Venezia

Bimetallic Au-Pd catalysts supported on amorphous silica-alumina (ASA) with vary amount of alumina (0, 8, 14, 28 and 100%) were prepared by the simultaneous reduction of palladium and gold precursors by ethanol in the presence of the polyvinylpyrrolidone (PVP). X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated formation of alloyed Au-Pd particles. Ammonia temperature programmed desorption measurements were performed to monitor the acid strength and the amount of acid sites on the catalysts after their reduction with 10%H2/Ar at 573 K for 1h. The effect of the support acidity on the catalytic activity was investigated in the simultaneous hydrogenation (HYD) of toluene (T) and naphthalene (NP) in the presence of dibenzothiophene (DBT). Coke formation was also determined. Under the selected conditions (P = 5.0 MPa, T = 523 K, WHSV = 41.2 h-1), all the catalysts were resistant to poisoning with 113 ppm of S (as DBT). The hydrogenation activity of toluene and the HDS activity of DBT were found to correlate with the concentration of the medium strength acid sites. The enhancement of the HYD activity and the S- tolerance was related to modifications of the electronic properties of the metal atom upon interaction with the Brönsted acid sites and upon intermetallic interaction.

Oct 1, 2003

By Jr. Santos, T. V. Pignaton, R. B. Gomides, W. Phillips, M. P. D. Gomes

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By M. Al-Hilal, G. Rajja, A. Al-Ali, Y. Jubeli

Abstract -A radiometric survey was carried out over clastic sediments in the immediate vicinity of some phosphatic sediments of Cretaceous age in the Wadi Qasser Al-Hallabat basin of central Syria. The objective was to explore for uranium and to define its dispersion pattern. This was based on ground radiometric surveys and geological studies. All ground surveys (using radon emanometry, track etching, gamma-ray survey and geochemistry) gave similar results, outlining the locations of the radioactive phosphatic formations in the basin, and indicating the dispersion pattern of uranium in the clastic sediments in the surrounding area. The dispersal of uranium from upper Cretaceous phosphatic formation occurs by mechanical weathering and chemical leaching by oxidizing surface waters. A rough estimate is that about one-third of the original uranium content of the Cretaceous sediments has been dispersed. Mechanical erosion is responsible for the main part of this released uranium, which now occurs in Recent sediments. However, the occurrences of spotty secondary U mineralization indicates that another small part of the available uranium must have been chemically leached out by the prevailing oxidizing waters, forming minor surficial minerals.

Jan 1, 1998

By Ahmad Hemami

A working code is developed to simulate the forces that are involved in the process of penetration of a bucket into bulk media during loading and excavation. The result of this work can be integrated with the simulation software that many manufacturers of heavy earthmoving machines introduce for training purposes. The simulator programs for machines such as backhoes, loaders, LHDs and the like, used for operator training, are usually only based on the kinematics of the machine. As a result, there is no indication of the effect of the medium when the cutting tool of such a machine touches the excavation material. This is like moving the machine in the air. Feeling the resistance force of medium to cutting by a bucket or blade during loading and excavation is more realistic, both mentally (by vision) and physically (feeling resistance in pedals and levers). The results from force simulation can be used by feedback in creating simulated resistance in these training gears, similar to what is done in flight simulators for aircrafts. In addition to serving for the above purpose, the results of this work can be used as a tool for examination and verification of the effect of a control policy for automation of loading and excavation of bulk media. So far no commercial product has been introduced that has such a capability, despite some extensive research on the subject.

Aug 1, 2013

By C. Graham

Mechanisation has been a predominant theme of the past 50 years in the mining industry, particularly underground mining. As the level of technology employed has increased, the anticipated productivity gains have not been realised and the differences are not explained by the demand for higher standards of safety and security. Now, mining costs are so high and productivity so low that the resultant return on investment for many Canadian operations has fallen to levels considered unacceptable in a competitive capital market. Simply continuing technological development cannot reverse this trend and its financial implications. The focus on technological development has distracted us from some basic truths. Systems that are more complex are more likely to fail and cost-effective processes depend on the continuity of productive activity and the flow of material. When putting these facts together, it becomes clear that in a system that has fixed external conditions, the single most crucial issue is the effective management of the operational cycle. By its nature, technology focuses our attention on what gets done and how it gets done, while the crucial issue is the increasingly longer periods in the operational cycle when nothing productive is being done. What is required is to match the level of technological complexity to the fixed system conditions, which are virtually unchangeable. This paper looks at the overall system and objectives and attempts to present an appropriate level of technology for the Canadian mining industry, now and in the foreseeable future.

May 1, 2004

By Barbara Kirby

Mining Industry HR Challenges Mining industry needs to hire approx. 100,000 workers by 2020 Attraction and retention of talent in all occupations Mobility of skilled workers between mine sites 70 percent of employers expect labour shortages over the next 5 years. Largest shortages: -physical sciences and engineering occupations -trades and ?undesignated? occupations ?Undesignated? Occupations ?Undesignated? Occupations -eg. mill operators, production / development miners and heavy equipment operators More than 20,000 workers will be needed by 2020 in the undesignated occupations and another 11,500 tradespersons Turnover rate for trades and undesignated occupations at mines is high: 8.3% compared to 5.6 % for all other occupations There is no system to recognize the skills of high-demand undesignated occupations

May 1, 2010

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001