Search Documents

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983

By Y. Mercadier, M. Ait-Ali, M. Dostie

"This paper presents the results of an analytical study to assist in the design of blast furnace tuyeres, including a prediction of the heat transfer process.IntroductionA blast furnace tuyere must be made of a material which must con serve its geometric and structural integrity in the environment of the fire-ball of the furnace. It must be cooled by a fluid forced through its internal cavities in such way as to keep its maximum temperature below the allowable limit. The prediction of the convective heat transfer coefficient inside the tuyere is of great importance in the design of new tuyeres with increased service life. We have developed a computer program which can predict the convective heat transfer coefficient for two-phase flow. This paper shows how the program work s and how it can be used for the numerical simulation of tuyeres.To simulate the h eat transfer conditions in water-cooled tuyeres, one has to predict:a) The heat flux (radiation and convection) generated by the combustion gases. This was evaluated using the single-zone gas-furnace model. This model yields results which are of the right order of magnitude. A more fundamental study of radiation heat transfer based on combustion and gas concentration s will be reported in a future publication.b) The local convective heat transfer coefficient at all points with in the tuyere.Prediction of the Convective Heat Transfer CoefficientTo calculate the convective heat transfer coefficient for refrigerant stream, semi-empirical correlations developed by the nuclear industry were adopted. These correlations permit us to analyze the entire range of the convective boiling range, as shown in Table 1. Our first attempt, with a single-phase flow correlation, has shown the need to take nucleate boiling into account."

Jan 1, 1982

By E. N. Durussel

"The Fox Mine has been producing copper/ zinc ore since 1970 at a rate of approximately one million tons per year, and until 1978all production was derived from longhole open stopes. In June 1978, a trial stope using bighole mining methods was started to eliminate the development of two sublevels between 400 level and surface. The trial proved to be successful, and bighole mining is now an accepted mining method for both stopes and pillars at Fox Mine.When production blasting was started in the first stope, the biggest problem encountered was the production of large amounts of sulphur dioxide gas as a result of secondary sulphide dust explosions. This gas generation resulted in lost production time and caused minor damage to underground installations to the blast level, and to the headframe. Sulphur dioxide generation has been noted in secondary drawpoint blasts and, on rare occasions, in drift rounds.This paper discusses the occurrence of the sulphur blasts and the practices and precautions used to prevent their reoccurrence at Fox Mine.IntroductionThe Fox minesite is located 30 miles southwest of Lynn Lake, Manitoba. With production startup in 1970, Fox Mine is owned and operated by Sherritt Gordon Mines Limited.The Fox orebody occurs as a large lenticular zone of semi-massive sulphides approximately 1,500 feet long and 15 to 100 feet wide running east and west. Dipping 70 degrees to the north, the orebody tends to bottom out at the 3200-foot level and reaches to within 15 feet of surface."

Jan 1, 1981

By Bo R. Arvidson

"New permanent magnetic alloys have recently opened up possibilities for development of unique mineral separators. These are now making several new applications feasible. In many cases where conventional electromagnetic-induced roll separators have traditionally been used, the new permanent magnetic roll separators may reduce both over-all capital costs and operation costs.The development of the next generation of extremely powerful permanent magnets, i.e. neodymium-iron alloys, is progressing rapidly and will affect the roll separator as well as another type of magnetic separator. Permanent Magnet Roll SeparatorDesign and FeaturesDiscs of permanent magnets interleaved with soft iron discs constitute the basic magnetic roll design (Fig. I). By enveloping the magnetic roll with a thin abrasive resistant belt (Fig. 2), even highly magnetic particles are removed.The first prototype roll utilizing the new magnets was shown to have approximately equal strength as induced magnetic roll (IMR) separators. Since the initial test roll, the new separator, called the PERMROLL® , has been made twice as strong with regard to magnetic force, that is, the magnetic flux density is determined to exceed 1.7 tesla (17 kilogauss), while the magnetic field gradient is more than twice the gradient than can be practically achieved with IMR."

Jan 1, 1985

By G. W. H. Norman

Introduction During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in the mapping of major faults by using aeroplane photographs with a scale of about 1,000 feet to one inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately. The information regarding faults and structure is so widely scattered that it is difficult to obtain a clear picture of the essential features, either for planned prospecting or for analysis and development of ideas for further study. This paper, as originally conceived, was intended only to discuss and compare the regional structure of southern Abitibi county-where detail mapping and diamond drilling have been carried on intensively for the past ten years-and of the less well-known Chibougamau district, in order that the experience gained in the one area could be usefully applied in the other. However, a comparison of the two districts leads naturally to a consideration of their common relationship to certain major late-Precambrian structures that form an important northeast system across the southeastern part of the Canadian Shield.

Jan 1, 1946

By C. Chapman, P. Cowx

"INTRODUCTIONTetronics Research and Development Co. Limited has installed several plasma torches for steel heating in continuous caster tundishes. An extensive demonstration program on a 14 tonne tundish reported the following advantages of plasma heating.• close control of steel temperature to ± 5°C;• a reduction of the furnace tapping temperature of up to 20ºC, leading to savings in energy and refractories costs ;• improvement in steel quality, to produce a slab product with an equi-axed crystal structure and a reduced number of large sub-surface slag inclusions;• the virtual elimination of oxygen pickup in the tundish; and• the capability of making ferroalloy trim additions to the tundish to permit a change of steel grade during casting, greatly decreasing inventory costs.The Need for Tundish HeatingIn the continuous casting of steel, the function of the tundish is to transfer the molten metal between the ladle to one or more continuously fed casting moulds. Figure I shows a typical temperature profile of molten steel in the tundish over the first cast cycle. It is observed that a rapid drop in temperature occurs both at the start of the cast, due to the tundish refractories absorbing heat, and also during ladle changeover. In addition, as a result of thermal losses through the ladle sidewalls, there is a gradual decline in the bulk steel temperature over the entire heat cycle. Consequently, in normal tundish operation, it is necessary to cast with a high superheat (25°C to 30°C + above steel liquidus temperature) in order to prevent freeze-up of the strand. Problems of high temperature variation and the potential of the steel solidifying in the tundish are greater for small caster units of low thermal mass . A high steel superheat increases the steelmaking vessel process time and refractory wear and prevents the formation of a uniform equi-axed solidification structure in the cast steel, resulting in centre line segregation and porosity. The large drop in the casting temperature that occurs during unsteady state operation causes an increase in the number of sub-surface inclusions, reducing the value of the product. Accordingly, plasma heating may be employed to maintain the molten steel at an optimum temperature to produce a slab of consistent quality."

Jan 1, 1989

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By S. N. Bhatnagar, S. K. Haldar

"Mineral exploration is an expensive speculative venture and calls for optimization of sampling. Exploration is generally planned in grid pattern to be conducted in phased manner. The objective of any such campaign is to assess the quality, quantity and its reliability. The traditional estimation methods are unable to provide a means of calculating the degree of reliability. Application of mathematical models can quantify the precision of estimation and bring forth decision-making criteria at any stage.In this paper three statistical and geostatistical models, viz., Frequency, Probability, and Semi-variogram, have been employed to evaluate sequential exploration data of RampuraAgucha zinc-lead deposit. The optimization in exploration for a specific objective has been highlighted.IntroductionAny exploration campaign demands heavy resource investment starting from the collection of the first sample to the production of the first ton of ore. The best estimation would be if the entire orebody is taken out and sampled. However, this is neither possible, nor desirable. Drilling is the primary tool of geological sampling. It shares the major portion of the investment and, thereby, warrants critical analysis at every stage during the ongoing exploration projects.The exploration program should be conducted as a well planned scheme based on a sequential evaluation approach in a phased way to achieve a specific objective. It would then be possible to evaluate exploration data at the completion of each phase by employing computer-based mathematical techniques to quantify the precision of the estimate for fulfillment of objectives. The subsequent drilling program should be modified accordingly."

Jan 1, 1987

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By F. P. Yungwirth

"IntroductionTrout Lake Mine is located about 5 km north of the Hudson Bay Mining and Smelting Co., Limited complex at Flin Flon, Manitoba. The mine was brought into production in 1982at the onset of a severe recession in the base metal market. The mine is operated as a joint venture with HBM&S, MMR and SMS.During the first several months of operation it became evident that there were opportunities to reduce costs at the mine significantly, and a productivity improvement subcommittee was formed to make recommendations. The first committee met in January, 1983 and consisted of the mine manager from Hudson Bay Mining, a geological expert and a maintenance expert from Outokumpu Oy, Finland, and a mine manager from Granges, Sweden.Recommendations from this committee were implemented during 1983 and a new subcommittee was constituted in 1984 to continue the work begun the previous year. The committee remains as constituted in 1984 and meets quarterly.The committee consists of M.A . Kirby , manager - Flin Flon Mines, HBM&S; Gustav Hoberstorfer of Mindelco , a Swedish mining consultant retained by Granges; Eero Laatio, mine superintendent of Keretti Mine at Outokumpu Oy in Finland; and Bob Bray, a mining consultant retained by Manitoba Mineral Resources.Many productivity improvements made in the operation are attributed to the work of this committee and other experts retained at various times throughout the mine life."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Godfrey W. McDonald, Dennis E. Fredrickson

"Commercial coal mining has been recorded in Nova Scotia since 1863 and during this period an estimated 60,000,000 short tons of mine discard containing 10 1030% coal has been accumulated, Approximately 70% of these dumps are in the Cape Breton region and most are owned by the Cape Breton Development Corporation (CBDC), formerly DEVCO.The explosion of oil produced energy costs which created an increase in thermal coal demand as well as the desire to rehabilitate abandoned mine dumps encouraged coal reclamation. CBDC was receptive to a proposal from the Selminco Joint Venture and encouraged the building of the Princess Recovery Plant (1980) and The Summit Plant (1982).The mine dump contains scrap, waste rocks, coal and substantial quantities of fine shale. The scrap and oversize are removed and the remaining material slurried with water to a density of 1.45. The slurry is cycloned to separate the saleable thermal coal from the rejects which are returned to designated areas of the dump for contouring and revegetation.BackgroundThe recorded coal production in Nova Scotia from 1863 to 1980 was 390,000,000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia. The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy CostsThe explosion o f energy costs in the mid-1970s greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental benefit of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation."

Jan 1, 1983

By Donald C. Craighead

"Overland conveyor systems to transport bulk materials from mines to processing plants or load-out stations have to be seriously considered as the viable alternative to truck and train haulage systems. With the ever-increasing price of diesel fuel, conveyors with their electrical drives generally prove to be the least costly when operating and maintenance expenses are analyzed for the life of the installation.IntroductionOverland conveyor systems are now considered as one of the viable alternatives which should be closely investigated when a mining company and its engineers initiate studies on methods of transporting raw materials from a mine to a processing plant or rail load-out station.This paper will generalize the overland conveyor and compare it with alternative handling systems. Each installation must be carefully studied to determine the best route, type of foundations river crossings; amount of excavation work for cut and fill, maintenance roads, etc. No two locations are the same nor are the principles of operation of an overland conveyor the same as those of a normal plant or mine belt conveyor. The proper time and effort must be put into the study of the system to evaluate the costs for comparison with other systems.The length of the overland conveyor depends on the layout of the mine and plant and the topography of the terrain between the terminals. Individual lengths may be up to 20 km, and a series of conveyors may extend 100 km or more.Advantages of Overland ConveyorsThe main advantage of overland conveyors is the low operating and maintenance costs which will be realized over its years of operation. Although truck haulage probably will permit lower capital investment during the initial phases of the mine development when the annual capacities have not developed to the design level, their operating and maintenance costs will be considerably higher. When evaluating the total costs per ton of material to be handled during the expected life of the operation and the projected increases for diesel fuel versus electricity, overland conveyor systems will generally prove to be economically more viable."

Jan 1, 1982

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By D. MacGREGOR, VERA TUREK

The Badgeley Island quartzite deposir in Georgian Bay is worked by lndusmin Limired and was developed in 1969 to produce a high-qualiry silica for use in rhe ferrosilicon and glass industries. The quartzire is part of the Precambrian Bar River Formarion, and is a generally whire, fine-grained rock containing rhin sericire seams. Primary sedimenrary features wirhin the deposit are bedding and ripple marks. Amphibolite and diabase dykes cur the quarr zire body.

Jan 1, 1984

By P. A. Verhey

"This paper describes a series of wear-resistant ceramic materials which have been successfully used in the mineral processing industry in Canada. Applications include use with metallic ores, coal, potash and asbestos, and in other processes where wear degradation is of major concern. The paper will also deal with considerations involving the selection of the different ceramic materials available. It will cover the installation of ceramic materials on support structures under varying process ' conditions, as well as the other physical and chemical factors which have to be taken into account.IntroductionIn the mineral processing industry, large volumes of ores tailings and other materials are handled. The abrasive nature of most of these materials results in extensive wear to both handling and processing equipment.Wear ratios versus cost, production losses due to down time and wear-resistant material suitability for a given application all demand particular attention when viewed against the need for increased efficiencies in existing processes. As a consequence, a very active continuous search for materials with improved wear resistance has been carried out for many years.In this search, starting about 20 years ago, dense ceramic materials were tested and evaluated in certain applications, notably in the iron ore and asbestos operations in Eastern Canada. As a result of substantially better performance both in continuous extended life and ultimate economics realized , wear-resistant ceramic applications developed progressively in many other processing applications, replacing traditionally used materials.In the vast majority of wear-resistant ceramic applications, considerable extended life over previously used materials was established. This invariably was not just a fractional increase but, in most cases , in factors of double, triple and often all the way up to 18 and 20 times the life of alternative materials used previously. In certain applications, extended life could not be measured and appears to be indefinite.Obviously, as a result of such experiences, the progressively wider use of wear-resistant ceramic materials is now an established trend."

Jan 1, 1981

By Robert B. Parsons

"This month, Tax Notes focuses on two features which can potentially ""dress up"" a new issue of common shares to make the shares more attractive to investors. Attaching warrants to a share issue is a relatively common practice, and recent years have seen an imaginative variety of different kinds of warrants, some of which can be subject to somewhat different tax treatment . A less common financing strategy which certainly deserves some consideration involves the possibility of utilizing ""Share Purchase Tax Credits "" in conjunction with a new share issue.IntroductionPrevious subjects covered in Tax Notes have dealt with flow-through shares and other tax angles which can make equity issues more appealing to potential investor s. Two other techniques which can add zest to a new stock issue involve the utilization of warrants and ""share purchase tax credits"" (or SPTCs). This article takes a brief look at the better known subject of warrants and the lesser known matter of SPTCs.Of course, this paper presents only a relatively general summary of the income tax implications of warrants and SPTCs, and is not intended to be a definitive commentary on all of the detailed and complex tax issues that might be relevant in the circumstances."

Jan 1, 1985

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By A. Mcdonald

"An X-Met Analyzer was purchased from Outokumpu in late 1983for use in the Hudson Bay Mining and Smelting smelter. Its first use was in the fuming plant to give zinc assays of each charge of slag tapped from the fuming furnaces. This quickly told the operators exactly when each charge had reached its economic tap-out point, and gave supervision a fool-proof method of identifying good operation. These and other factors led to major improvements in coal utilization in the fumers and to major increases in zinc oxide production. A second unit was later purchased for the reverberatory furnace to give silica and iron assays of the slag, and these were used to make adjustments in the feed composition to maintain the desired SiO2:Fe ratio in the slag. Since purchasing the units for the furnace, the oil consumption and copper content of the slag have dropped significantly. IntroductionSmelters have lagged far behind concentrators in process control by mean s of rapid product analysis. The on-stream X-ray analyzer was developed about seventeen years ago, and soon concentrators around the world were getting assays of the incoming ore, .concentrates and tailings every fifteen minutes, and using these to control reagent additions and other process variables. Almost always, the concentrate grade and recovery improved.In smelters, product streams are solids or molten materials, not the more easily handled slurries, and until seven years ago no inexpensive equipment was available to provide rapid analysis of this type of material. In approximately 1980, several companies developed instruments based on irradiating solid samples with low-intensity gamma rays from radio-isotope sources, and measuring the secondary X-rays emitted from different elements in the sample to provide an analysis of the elements desired.The smelter staff had a close look at what was needed and listed the following points as being critical:1. ability to provide Zn assays of a sample of slag within 15 minutes of taking it, in order to achieve optimum fuming times (zinc fuming , being a batch process, had the greatest potential benefit from rapid slag analysis);2. ability to give Cu and Fe assays on the slag, and on other smelter products, such as matte and converter slag;3. ability to give Si02 assays since the SiO2 content of the slag has a strong effect on fuming rate; and4. ability to stand up to an industrial atmosphere such as exists in the fuming plant."

Jan 1, 1987