Search Documents

Scope / Agenda ? What is Situation Awareness (SA)? ? Background on SA theory ? SA is critical in a wide variety of domains ? SA and human performance ? Consequences of poor SA ? Significant challenges for SA in mining operations ? Technology centric design ? SA-oriented design methodology ? Goal-Directed Task Analysis ? Design ? SA Measurement and Evaluation ? Applications of SA-oriented design

Aug 1, 2013

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By R. O. Burt

"Gravity Concentration, the oldest form of Mineral Processing, remains of major importance to the Industry. Current applications of Gravity Concentration are briefly examined.The Paper details one approach to the development of a Gravity Concentration Plant, from laboratory and mineralogical techniques, through Pilot Plant testing, where applicable, to the actual design of the plant.INTRODUCTIONGravity Concentration, once the major method of concentrating minerals has, for much of the twentieth century been regarded, like the dodo bird, as obsolete. However, in more recent years it is enjoying something of a renaissance, and is once again being treated as a useful, economic alternative in the Mineral Processing Engineers' arsenal.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive."

Jan 1, 1984

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By F. Hassani

This Paper describes a sudden spill of rock waste used for backfilling from a waste pass at one of the underground mine in Canada thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in future. The investigators from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied and appropriate measurements were taken and samples of the waste material was collected for further test and analysis. The field visit and the interview of the witnesses allowed a detail documentation of the events. The sequences of events related to the incident together with the experimental results obtained in the course of the investigation is detailed. The waste material was characterised in the laboratory with regard to its behaviour in the presence of water. This information is then discussed and the failure mechanism involved in this accident is identified. The full recommendation as well as the immediate operational measures implemented by the mine to prevent future occurrence of such events are discussed and presented.

May 1, 2003

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By G. O. Allard, A. Gobeil

The Chibougamau area is the eastern segment of the MatagamiChibougamau greenstone belt. The Archean rocks of the area consist of two mafic-to-felsic volcanic cycles ( Roy Group) overlain by a sedimentary-volcanic sequence (Opemisca Group). The Roy Group volcanics are intruded by many coeval and comagmatic differentiated gab bro sills. The Supracrustal rocks of the Roy Group and Opemisca Group have been folded about north-south axes, refolded isoclinally about east-trending axes and metamorphosed to the greenschist facies. The same lithologies have been identified east of the Grenville Front at amphibolite grade. The first volcanic cycle consists of 3000 metres of porphyritic pillowed basalts and comagmatic gabbro sills (0batogamau Formation) overlain by a thin sequence of felsic pyroclastics, porphyritic dacites, and iron formation (Waconichi Formation). The Dore Lake Complex is a sill-like layered complex intruded in the upper part of the Waconichi Formation. The second cycle consists of 3600 metres of pillowed basalts and gabbro sills (Gilman Formation) overlain by a volcanosedimentary assemblage less than 1000 metres thick (Blondeau Formation). The Cummings Complex consists of the Roberge sill (dunite and peridotite) at the base, the Ventures sill (gabbro) and the Bourbeau sill (leucogabbro and quartz ferrodiorite) at the top. It is emplaced within the Blondeau Formation. The Opemisca Group sediments and minor porphyritic K-rich andesites (Stella, Hauy, and Chebistuan Formations) form narrow belts preserved in the synclines of the area. The Proterozoic rocks of the Chibougamau area consist of conglomerates, arkoses, and argillites with dropstones of the Chibougamau Formation. North of Chibougamau, the Mistassini Basin forms an elongate northeast-trending basin filled with sediments of the Mistassini Group. Conglomerates, sandstones, argillites, dolomites, stromatolitic dolomites, and iron formation are the principal sediments within the basin.

Jan 1, 1984

By Eric Konigsmann

"The Pogo project is located on the Goodpaster River, 38 miles north of Delta Junction in east central Alaska. Sumitomo Metal Mining and Teck Corporation are planning to develop a 2,500 ton per day underground mine and mill at Pogo. A preliminary resource of 5.5 million ounces of gold has been identified in two flat lying lenses. An underground adit has been developed to facilitate underground drilling of the deposit and to provide samples for bench and pilot scale metallurgical testwork.Flowsheet development included the evaluation of several processing options. The final flowsheet selected includes SAGhall mill grinding, gravity concentration with intensive cyanidation and direct electrowinning, sulfide flotation with ultrafine regrinding, and cyanide leaching and CIP gold recovery from the flotation concentrates. Flotation tailings will be filtered for placement in a dry stack storage facility or disposed of as paste backfill underground. All of the CIP tailings will be disposed of underground as paste backfill. A pilot plant was carried out to evaluate the proposed flowsheet described above and to confirm the gravity recovery predictions.Great care was taken in the development of the flowsheet and site layout concepts to mitigate the environmental impact of the proposed operation. An overview of the site water management concepts is presented and the impact of water issues on the process flowsheet is discussed."

Jan 1, 2002

By Doug Smith, Ross MacFarlane

"The Star Lake Mill was commissioned by Cameco (formerly Saskatchewan Mining Development Corporation) in 1986 to process a small high grade gold deposit in a remote location of Northern Saskatchewan. The lean approach to the 200 t. p. d. CIP mill to minimize capital and operating costs employs a number of unique features which are described along with highlights from the initial two years of operation.1.0 INTRODUCTIONThe Star Lake Mine is located 520 kilometers north of the City of Saskatoon (Fig. l) with the nearest population centre in La Ronge 130 km to the south. Gold showings were first discovered in the area in the 1940's with the Star Lake ""21 Zone"" ore body discovered in 1983. The Star Lake Mine started operations in 1986 becoming the first primary gold producer in Saskatchewan in over 40 years. The mine is operated by Cameco (formerly SMOC) with 50\ ownership in a joint venture with starrex Mining Corporation (35\) and Uranerz Exploration and Mining (15%).The limited reserves coupled with the remote location and the price of gold ($300-$350 u.s./oz) at the time the project feasibility was being assessed required a lean approach to make the short term operation successful. This paper describes the approach taken in the design and construction of the Star Lake Mill and describes the mill operation with highlights of the initial two years of operation."

Jan 1, 1989

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By Lutz Markworth, Fernando Parra, Wolfram Jaspers

"The worldwide demand of iron ore and the depletion of the high-purity deposits make it necessary to recover ores in increasingly fine size fractions or low Fe content in the feed material. Impurities for Iron ore processing plants are mainly Silica, Al2O3 and Sulfides.There is a copper processing plant in Chile, which has a high content of Fe in its tailings. These tailings will be re-processed to recover the Fe and to produce a pellet feed concentrate. This challenging flotation process was developed by the customer in his own laboratory. Different flotation technologies were tested. The best results were achieved with the PNEUFLOT® (PNEUmatic FLOTation). For a feed capacity of approximately 600 t/h, a flow sheet of two flotation lines with a reverse two-stage Amine-Silica flotation followed by a single stage reverse Xanthate Pyrite flotation was developed.Because of the two impurities the process control is very critical. Not even the reagent dosing has to be flexible for changes in the feed material; also the flotation cell has to be adaptable. Continuous development of the PNEUFLOT® cell with their specific advantages and the elimination of dysfunctions in the PNEUFLOT® cell have led to a growing demand of this type of equipment worldwide for the iron ore industry within the past years.INTRODUCTIONThe worldwide increasing demand of iron ore is mainly caused by China. This has a major impact on all economics worldwide as the metal price indicates. However, not even the iron ore and steel price, but all other commodities prices and the precious metals prices are increasing by a high percentage. Figure 1 shows the iron ore (pellets) price increase for Fe and the import of iron ore by China. Figure 2 shows the imports of iron ore to China."

Jan 1, 2008