Search Documents

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

[ ]

Jan 1, 1994

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

Jan 1, 1992

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By Martin J. Pedley

The use of soil nailing has grown steadily in the UK over the last 15 years and it has recently become more popular in the Republic of Ireland. This paper presents three soil nailing temporary works case histories where the technique has been used to support steep excavations in difficult ground conditions. It demonstrates the effectiveness of soil nailing when applied in appropriate conditions. Details of design methods and construction techniques are described and those aspects of soil nailing that will benefit from further study and development are identified.

Jan 1, 2000