Search Documents

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By John S. Pack

The last 25 years have seen rapid expansion in the use of helical screw pile foundations and tiebacks for new and retrofit construction of buildings and earth retention structures. An estimated $100 million was spent in 2002 on helical foundations and tiebacks in the United States alone. While design information is available in the literature, information regarding quality control, inspection and performance monitoring is lacking. Recognition of at least one manufacturer's helical foundation material by the Uniform Building Code, Standard Building Code, and BOCA (all three codes now combined into the ICC International Building Code) has given added urgency to the dissemination of reliable and practical quality control, inspection and performance monitoring procedures. This paper describes a set of such procedures that have been followed for 17 years by engineers experienced in the industry who have directly installed or been involved in the installation of over 140,000 helical foundations and tiebacks in divers soil conditions for various types of structures, including earth retention structures. Topics covered include design responsibility, building code listings and requirements, manufacturer ISO certification, manufacturing process, material and installation specifications, installation contractor certification, field placement, installation procedures, field inspection, building code inspection and performance monitoring. The paper concludes with a step by step example of practical quality control, inspection and performance monitoring procedures on a typical helical foundation project.

Jan 1, 2003

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1997

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Richard W. Hanford

The geotechnical construction industry generally considers soil mixing to be defined as an in situ ground improvement or treatment method by which a dry or wet reagent is introduced into the ground and is blended with the soil by mechanical or rotary mixing tools. This results in relatively homogenous mixtures whose engineering properties are improved and are greater than the soil properties before mixing. Reagents usually include cement, but may also include processed clay such as bentonite, when a reduction in hydraulic conductivity is desired, or other proprietary chemicals when chemical stabilization is the objective. Mixing may be either shallow or deep. Shallow Mixing is the term arbitrarily used for treatment of soils within the upper 30 feet; Deep Mixing denotes treatment below 30 feet to the depth limits of the equipment. Mixing equipment may consist of single or multiple-shaft tools having cutting and mixing blades of many different configurations. To avoid using proprietary nomenclature, reference to Shallow Mixing Methods (SMM) and Deep Mixing Methods (DMM) are the preferred terms. Although originally developed and patented in the United States in 1956, in situ construction using various soil mixing methods is more prevalent in Japan and the Scandinavian countries. Reintroduced into the United States from Japan in 1986 for ground improvement and liquefaction mitigation at Jackson Lake Dam, Wyoming, acceptance of soil mixing methods has been gradual but slow. Applications typically include:

Jan 1, 2001

By Per Eriksson

For light buildings on clay, foundations on L/C-columns is in many cases a competitive alternative to piles when the thickness of the clay is moderate (<20 m). The method is applicable for the above mentioned depth when the clay is normally consolidated, and for thicker deposits when the clay is overconsolidated at depth. This case study concerns a shopping mall in Nordby, Sweden, founded on L/C-columns (5-15 m in length) and generally spaced 1.45-2.0 m (spacing 0.7 m was used below pillars). The base slab was built as a raft foundation, using fibre reinforced concrete.

Jan 1, 2000

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

Jan 1, 2001

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta&apos;s harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991