Search Documents

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.It was found that the digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was a merit to apply the sludge to agriculture in dry areas. Anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion. The anaerobic digestion sludge could be considered as a humus-rich hygienic product that improves soil fertility and water holding capacity, nourishes plants and immobilizes heavy metals in the environment"

Jan 1, 2003

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By Kevin Galvin, Simon Iveson

Fine particles are the most valuable because they are the most liberated. However, they are also the most expensive and difficult to recover and concentrate. The Reflux Classifier is a novel invention that combines many of the virtues of existing fine particle separation technologies in a way that provides profound synergies. Multiple parallel narrow channels create a laminar-shear separation zone. The laminar flow provides a well-defined velocity gradient that exposes particles on the wall to a conveying velocity that is approximately proportional to their size, thus reducing the dependence of elutriation velocity on particle size. The high shear rate in these channels generates a hydrodynamic lift force that selectively lifts low-density particles off the channel wall and thus causes them to be preferentially conveyed out in the overflow. Particles that are not elutriated slide back down into the mixing reflux zone beneath the inclined channels which gives them multiple opportunities to re-enter the channels. The resultant suspension of both coarse and fine high-density particles in the fluidized bed zone at the base of the unit generates a strong autogenous dense medium that helps to direct large low-density particles back up to the overflow. The fluidization water also simultaneously de-slimes the high density underflow product. When placed in a centrifuge, the benefits of these features multiply with the improvements in capacity and selectivity that arise from high G-forces. When inverted, these features can be used to perform flotation well beyond the conventional flooding limit. Hence this invention platform has the potential to dramatically improve both gravity and flotation separation performance across the minerals processing industry.

Jan 1, 2014

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By Y. G. Sun

This paper mainly reported separation manganese silver oxidized ores process by amylum de-gradation reduction and its influencing factors. When dosage is given according to nMn : nH2SO4 : n(C6H10O5)n : nH2O=1:k21.8: k116.66:30, the amount of up to 95.93% Mn leach rate and less than 2% silver loss can be obtained. Cyanidation process was used to extracted silver from leaching Mn residues. Silver leach rate could reach 94.15% at consumed amount of 1kg/t NaCN for 1h. Silver leach recovery rate was more than 92.27% by leaching Mn and cyanidation two-step processes so manganese and silver were separated effectively.

Jan 1, 2014

By W. Y. Liu

A sulfate reducing bacteria strain (named SRB-A) is isolated from sanitary wastewater by using anaerobic technology of Hungate. The studies of physiological, biochemical and phylogenic of the isolated strain are carried out. The colonies of the strain are circle. Cells that are slightly curve, rod-shaped with the size of 1.0~3.0µm in length and 0.8~1.0µm in width. The optimum temperature for growth of the organism is 30~35°C. The optimum pH for growth is 7.0~7.2. Strain SRB-A can use sodium lactate, sodium citrate, sodium acetate, ethanol and acetone as electronic acceptor but can not use glycerol, glucose, sucrose and sodium oxatate. The isolated strain reduces sulfate, sulfide, sulfur, DSMO and FeCl3, then nitrate and nitrite can not be used. The strain has higher tolerance of NaCl, and the optimum growth occurs in the presence of 5%~8% (w/v) NaCl. The result of 16S rDNA sequence analysis indicates that the isolated strain SRB-A is the most similar to Desulfo-vibrio halophilus, and the level of the similarity was 98.4%. The isolated strain has a stronger ability to reduce sulfate, and the level of sulfate reduction reaches about 90% at pH 7 in the liquid medium. 0.6 to 0.8 is the optimum COD/SO42- in the medium for the isolated strain to show better ability to reduce sulfate. At pH 2.5 the level of removal of Cu2+ reaches 96.3%. Under the condition of pH 3.5, the level of removal of Zn2+ reaches 92.6%. When the value of pH reaches about 7, the Fe3+ is precipitated by the formation of Fe(OH)3, and Fe3+ is removed up to 89.4% at last.

Jan 1, 2014

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

The ore studied occurred in the Three Rivers area in China and was a silver-lead-zinc complex ore containing 400.52 g/t silver, 4.77 % lead and 3.47 % zinc. Silver, lead and zinc were the major valuable elements in the ore and copper, cadmium and tin were the associated elements to be comprehensively recovered, whereas arsenic was the harmful element. The element silver occurred mainly in freibergite with small proportion in dyscrasite and other silver minerals. The carrier minerals for silver were mainly galena and oxidized lead minerals and then sphalerite, arsenopyrite and pyrite. The ore contained numerous minerals with complex mosaic texture and the lead and zinc minerals enclosed each other multiply, which made the separation of the minerals in the ore very difficult. Experimental investigation on the beneficiation of the ore indicated that with flotation separation process it was very hard to obtain single lead concentrate or single zinc concentrate that would meet the requirement of market. In the meantime, during the separation process of lead and zinc, silver tended to be dispersed, resulting in a low recovery of silver. Therefore, a rational utilization technique for the ore should be a combined process of bulk flotation to reduce arsenic? sulphating roasting of silver-lead-zinc bulk concentrate-leaching with diluted sulphuric acid to separate silver, lead and zinc. With this process quality lead concentrate containing silver and high grade zinc product and silver product could be obtained. The recovery of silver, lead and zinc in flotation was 85.10%, 84.48% and 82.48%, respectively. The total recovery of silver, lead and zinc in chemical processing was 97.07%(sum of recovery of silver ingot and lead concentrate), 99.61% and 90.93%, respectively.

Jan 1, 2014

The present study is devoted to improvement of the leaching efficiency during phosphorous removal from high phosphorous gravity-magnetic concentrate. Before leaching the concentrate has been subjected to roasting with the addition of either Ca(OH)2 or CaO. The oolitic iron ore is roasted at 900°C for one hour. This reflects in reaction between alkaline earth additive and quartz, aluminosilicates, phosphorus, and some other minor components of the gangue minerals. The application of leaching, physical separation, and wash out of salts has resulted in the decrease of phosphorus from 0.7 to 0.15 % and it is established that the major influencing factor is the concentration of acid and to a less extent duration of the leaching process. About two third of the phosphorus can be removed by roasting with 3 % CaO to hematite, coarse grinding to d50 0.3 mm, dry high intensity magnetic separation and leaching of the magnetic fraction with hydro-chloric or nitric acid.

Sep 1, 2012

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014