Search Documents

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

This paper discusses current workforce demand projections for mineral processing engineers and emerging trends in mineral processing education. Attempts are made to identify gaps that often result in a mismatch between skills taught and skills needed by the practicing engineer. Clear examples of this include a less than uniform training in chemical aspects of mineral processing, and an understanding of the statistical and experimental design tools necessary to tame the often-large variation in operational parameters and plant data. The end goal is an educational system modernized to prepare mineral processing specialists for productive careers in the sustainable development of natural resources. A framework for revamping education based on an integrated modular approach is also presented. Keywords: mineral education trends, mineral processing programs

Sep 1, 2012

By L. Rintala

The design of a hydrometallurgical process starts with the analysis of the raw materials to be treated, for example mineralogy, chemistry, deposit size are analysed. Based on this information suitable unit processes for pre-treatment, leaching, solution purification and product recovery are selected. Typically, process design for the new ore deposit relies on laboratory tests such as pre-treatment and leaching experiments. The experimental work is the most time consuming and expensive part of the process design. Reducing the number of experiments would shorten the time of designing a new flowsheet or development of new process technology. A large amount of information is available about the hydrometallurgical experiments and the amount is increasing continuously. For example, word search using ?hydrometallurgy? from Scopus database results in over 4 000 publications with the word in title, abstract or keywords. This number consists of 2 500 articles, 900 conference papers, and 90 reviews since 1972. The number of hydrometallurgical publications per year has increased from 13 in 1972 to 150-200 in the last few years. The objective of this study was to analyze how detailed data of experiments about the gold extraction is published and how that data could be exploited more effectively when designing hydrometallurgical processing for new ore. The leading idea is that similar ores should have the similar response in leaching. If the published information was used more efficiently, the amount of experiments would be reduced. More than 200 cases of experimental data of gold leaching have been analyzed for this study. There are over 30 factors that could be used in comparison when selecting process alternatives, but challenging fact is that not all these factors are documented in all publications. Results show that the usefulness of the published data in the development of hydrometallurgical flow sheet for gold using decision-support tools is not that straightforward. The quality of the published information about gold extraction varied between the publications and the descriptions of the raw materials, experimental arrangements and results were often missing details. Methods to normalize the data for description of the cases and a system to describe different features unambiguously are needed. Keywords: refractory gold, host mineral, leaching, data analysis, case-based reasoning

Sep 1, 2012

By C. Y. Jia

Adsorption of Thiooxidans ferrooxidans and Mycobacterium Phlei on the surface of pyrite and galena was studied. From the experimental results, it was observed that Mycobacterium Phlei adsorbed preferentially on pyrite than on galena at neutral and alkaline pH values, while Thiooxidans ferrooxidans is not at all pH range, and the scanning electron microscopy photograph also indicated that. FTIR and XPS of two strains of bacteria indicated that there are much functional groups on surface of them, such as O?H, N?H, C-O, C?N, C?O etc, but S-O group occurred on Thioox-idans ferrooxidans cell surface and the P-O group appeared on Mycobacterium Phlei cell surface, and the content of C?O?H and C?O?C groups on Mycobacterium Phlei cell surface is higher than that on Thiooxidans ferrooxidans cell surface, this also been known from UVS investigation. The affinity of these groups to metal ions on sulfide minerals is able to explain the selective adsorption.

Jan 1, 2014

By H. Sarvamangala

Selective separation of alumina, silica, calcite and apatite from hematite was achieved through microbiologically induced flotation and flocculation in presence of bacteria (B.subtilis) and that of hematite from apatite after interaction with yeast (Saccharomyces cerevisiae). Bacterial and yeast metabolites containing extracellular proteins were characterized from mineral-grown cell free extract. Bacteria and yeast can adhere to mineral surfaces and influence subsequent separation of the minerals. Bacteria functioned as a stronger depressant for hematite, while yeast cells depressed apatite at neutral pH. Selective affinity of the bacterial and yeast cells towards the mineral surface was observed through adsorption studies. Extracellular proteins (EP) were isolated from B.subtilis and yeast. The protein profile of the EP of bacterial and yeast cells grown in presence and absence of minerals was studied. This study has demonstrated the utility and amenability of microbially-induced mineral beneficiation of iron ores through bacterial and yeast cells and their metabolic by products.

Sep 1, 2012

By K. D. Mehta

Copper concentrate containing complex sulphides of Cu-Ni with 14.13% Cu and 10.04% Ni besides impurities such as 0.33% Co and 0.71% Mo, is not acceptable to the copper smelters due to the smelting problems. Selective bioleaching of nickel from the concentrate can be considered an an option to make it suitable for copper smelter. Effect of elemental sulphur and pyrite on the bioleaching of Ni and Co has been investigated using a mixed culture of Acidithiobacillus ferrooxidans (A.f.) and Acidithiobacillus thiooxidans (A.t.). Parameters such as pH, temperature, particles, size etc. were optimised to understand the role of additives in the bioleaching. With 2% S at 308K, 2.0 pH, 5% pulp density and 200µm size particles while shaking at 100 rpm, 79% Ni, 41% Co and 5% Cu were bioleached as compared to the leaching of 81% Ni and 45% Co in presence of 10 wt% pyrite in 60 days; 27% Ni, 24% Co and 4% Cu were recovered in sterile experiment. The selective dissolution of nickel and cobalt as compared to copper may be explained by galvanic interaction between chalcopyrite: pentlandite / pyrrhotite. Bioleaching was facilitated by strong oxidizing conditions due to higher Fe3+/Fe2+ ratio/redox potential (ESCE) as a result of improved interaction of minerals through biooxidation of sulphur and accelerated galvanic interaction by pyrite. The mechanism of selective leaching of Ni and Co was established by XRD phase identification.

Sep 1, 2012

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By S. N. Shahcheraghi

Grinding is one of the most important and expensive steps in mineral processing allocating about 70% of the total energy in the plants. Nowadays, for optimizing the energy consumption in these equipments, the rock behavior and its size distribution during the crushing have been normally predicted using selection and breakage functions to be able to optimally model and design grinding circuits. For this purpose, the case of Miduk copper mine in Kerman province, Iran was studied. The samples were taken from primary ball mills feed and were subject to screen analysis to achieve uniform sizes. Then, selection and breakage functions were determined at the different grinding times in laboratorial ball mill. Finally, ore size distribution in different grinding times was estimated using MATLAB software

Sep 1, 2012

By Erico Tabosa

The turbulence characteristics and measurement techniques for agitated tanks are well established for liquid and liquid-gas systems. However, the literature shows that the overall energy dissipation rate (related to turbulence) is affected not only by air addition, but also by the concentration of solids. Unfortunately, there are no reliable measurement techniques for characterizing turbulence in a three phase (liquid-solids-gas) environmental system, which is the case in a flotation cell. Therefore, the effect of turbulence on flotation kinetics is very much one of conjecture. The aim of this work was to develop a sensor to characterize the degree of velocity fluctuation, which is related to turbulence, in a flotation cell operating with slurry and air. This sensor comprises a piezoelectric film transducer that converts mechanical to electrical energy. Hence, when the sensor deflects backwards and forwards an AC voltage is created. Flotation studies carried out using this sensor in a 3m3 Metso RCS cell processing a copper sulphide ore showed a highly turbulent impeller zone with transition to a significantly less turbulent zone in the upper portion of the cell. The transition region moves as the cell operating variables are changed, for instance the impeller speed, impeller size, air rate and feed solids concentration. Keywords: mechanical flotation cell hydrodynamics, turbulence characterization

Sep 1, 2012

The status quo of ecological rehabilitation in metal mine in China and progress in the technology for ecological rehabilitation are presented, including soil reconstruction, soil improvement, plant selection. The present and future research fields are suggested: basic theory of ecological rehabilitation, operative technology of ecological rehabilitation, new technology application research and ecological rehabilitation plan, management and policy.

Jan 1, 2014

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure, for use in the prediction of flotation circuit performance, far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, data collected from an industrial flotation circuit is used to derive the parameters associated with two different types of flotation models. Simulations performed using these models demonstrate the need to differentiate between cell and feed properties. A model that does not differentiate between these two properties fails to successfully predict the metallurgical performance of a flotation circuit after a disturbance."

Jan 1, 2003

By Xiaodong Jia, Williams. Richard A.

This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. The ability to predict packing structure of real particle shapes and to compute directly some structure-dependent physical properties (such as liquid permeability, mechanical strength/ stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.

Jan 1, 2003

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. The starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions round the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions.

Jan 1, 2003