Search Documents

By A J. Rorke, U Chhika

"A series of tests was carried out on a dry blend of PPAN and LAN prills (LANFO). The objective of thetests was to determine detonation stability and VOD performance compared to ANFO. Heave andfragmentation results in the field were also evaluated visually. A number of factors were behind for.mulating this blend. A lower cost is combined with higher in-hole energies, but at slower reactionrates and lower peak borehole pressures. The resultant effect is improved heave characteristics andlower energy losses caused by inefficient crushing of the rock immediately around the borehole.The test results indicate that IANFO is ideally suited to blasting in softer midburden and overburdenrock types often encountered in coal strip mines."

Jan 1, 1995

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By Jose a. Sanchidrian, Ramon G. Eguren, Javier L. Amigo

On December 2013 a MEMU exploded at a blasting site in Norway, after burning for more than two hours. This paper describes the analyses made to determine the actual yield of the explosion, the lessons learned from the event and the actions taken as a consequence. The conclusions of the analysis were the following: - The yield of the explosion was 650-1450 kg TNT. In terms of AN and ANE they correspond to 1300 – 3700 kg AN, or 950 – 2450 kg ANE or ANE/AN blend. These quantities are 8 to 31 % of the explosive precursors in the truck. The burning of the truck and its load for two and a half hours had consumed more than two thirds (perhaps up to 90 %) of the explosive precursor material.

Jan 1, 2016

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Neal Lee, Braden T. Lusk, Jhon Silva-Castro, Patrick J. Jenks

"Timing and charge sequence are very important for optimized blast design. Traditional nonelectricinitiation systems have moved the industry toward a system of delays consisting of hole-to-hole androw-to-row timing sequences that mimic the application of nonelectric surface delays or dual delayinitiator systems that have been prevalent in the blasting industry for many years. The increasedutilization of electronic detonators allows for the use of Regular Rhythmic Timing (RRT) utilizing onlyone delay between charges and a selected charge firing sequence. The hole to hole and row to row (HHRR) timing method has been utilized for blasting optimization and allows for simplistic changes to the tie in phase of the blasting sequence. When using this traditional timing methodology, for some specific cases related to the number holes and rows, crowding occurs in the delay between charges with subsequent increase in the peak particle velocity (PPV) produced by the blast. This is in contrast to RRT where the timing between the delays remains constant."

Jan 1, 2016

By Robert Hopler

Some few years ago, when the cruiser “Brooklyn” was passing through the fairway to the southwest of the Battery, the ship being fully equipped with stores, etc., and therefore at her maximum draft, she grounded quite heavily upon some obstruction, and received injuries which necessitated her docking at the Brooklyn navy yard, where extensive repairs had to be made on her damaged bottom.

Jan 1, 2007

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

By Paul Sainato

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. A second survey was distributed in 2015 and included international students. This paper provides the data from a third online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2016

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

We had a cold, gray winter here in Kansas City and I spent a lot of time watching out my den window at the squirrels and birds trying to get by in the lousy weather. I remember too well working in the cold, loading shots. I was frostbitten several times since I couldn’t tie in MS connectors with gloves on. Those old connectors had a piece of detonating cord on either end of a metal tube that held the delay and you tied them to the trunk lines with square knots. Doing this on a “warm” day in Alaska or Montana shooting ditch for a pipeline could be a frosty experience. Also remember how hard it was to connect up electric caps (detonators to you new guys) in the cold. Now I don’t want you to feel sorry for me ‘cause I suspect most of you younger fellows have also paid your dues in the cold and for that matter in the heat too. Wowee, the heat at the bottom of a Chicago dolomite quarry in August was enough to fry the brains of all that were there. Maybe that’s why the third deck of my brains doesn’t exist.

Jan 1, 2004

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

By Peter Moser, G. Reihholf

Holcim, one of the world's leading suppliers of cement, aggregates and concrete, has set up a few years ago a working group “Quarry” in order to optimize the performance of its central European quarry operations in terms of work safety, environmental standards and economic performance. One of the activities of this working group "Quarry" addresses the subject of blast fragmentation in the quarries. A benchmark study of the blast work in all quarries has shown substantial differences for the various operations in terms of drill& blast costs. Especially big differences were found with respect to the drilling patterns as a function of the borehole diameters and with respect to the utilization of the borehole volume for charging the explosives.

Jan 1, 2006

By John Babcock, Bryan C. Smith

In a partnership between Luck Stone Corporation and Loudoun Water, a 42” (1.067m) steel pipeline was constructed along the perimeter of an extensive permitted reserve of diabase rock Luck Stone was about to begin mining. Loudoun Water provides drinking water and wastewater services to over 75,000 households in Loudoun County, Virginia. In discussions to establish the 30-foot (9.1 meter) easement for Loudoun Water within the permitted reserve of diabase rock, Luck Stone and Loudoun Water agreed on the following basic conditions: • Luck Stone could execute production blasting as close to the easement as physical conditions of overburden depth permits. We estimated the minimum distance to be about 75-feet (22.86 meters) from the centerline of the pipe. • Loudoun Water would install strain gauges on the pipe every 500-feet (152.4 m) along the entire length of the future reserve area. This resulted in the installation of 18 strain gauges. • Luck Stone would contract a third-party vibration monitoring company, agreed to by Loudoun Water, to monitor the strain gauges and provide seismograph reading at appropriate locations along the pipe as mining progresses. All information would be provided to Loudoun Water. • Luck Stone’s blasting will be conducted in a manner that ensures the recommended strains are not exceeded.

Jan 1, 2019

By Joshua Hoffman, Braden Lusk, Kyle Perry

This study explores how different geometries affect the shock tunnel’s performance and is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK and S&T shock tunnels. Phase 3: Analysis of the data to begin building a pressure-forecasting tool for the UK shock tunnel given the explosive characteristics, sample size and desired pressure and impulse.

Jan 1, 2009