Search Documents

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By B R. Spencer

Using bulk repumpable water gel explosives in underwater shooting results in even more benefits to the user than a "dryland" customer. It is nearly impossible to reshoot underwater, so a bad shot causes tremendous problems. The huge expense of operating drill boats, dredging buckets and clamshells makes shot loading, hookup and digging cycle times critically important.

Jan 1, 1990

By Thomas H. Kleine, Alan R. Cameron, William W. Forsyth

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By J R. Hearst, T R. Butkovich

Explosive-induced fracturing and permeability enhancement far from a free face were studied. A one-dimensional computer program, SOC, was used to predict the total failure-associated distortional strain, ef. Laboratory and field experiments associated the calculated ef with the observed fracture and permeability enhancement. An ef value of 0.015 corresponded to the observed radius of effect, which was about seven times the cavity radius and was consistent with predictions from SOC and from the literature.

Jan 1, 1976

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By K Ramachandra Rao

Joints, fractures and other structural defects bring anisotropic character Into a rock mass. Conventional methods of blast design In a rock mass consisting phyllites, mica schist etc., which are characterised by the presence of closely spaced, nearly vertical planar Joints, result In formation of large slabs which cannot be handled by the excavation and loading equipment without resorting to secondary blasting. Frequent secondary blasting Is not only expensive but also, Is a source of environmental hazard. Interruption of production cycles frequently, leads to uneconomical mining. This problem could be minimised by designing blasts which produce forces whose components along and across the joints/fracture planes Is lust sufficient to break the rock mass In both directions. Rock mass strength can be assessed from field and Laboratory tests. Projecting structural features with respect to bench orientation on a stereoplot helps In assessing magnitude and direction of force vectors required to fragment the rock mass to the desired size range.

Jan 1, 1995

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011