Search Documents

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011

By Dale S. Preece

A new three dimensional (3D) mechanistic model of fragmentation, called the Fracture Density Model (FDM) is used to simulate full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. The model uses several computational mechanics algorithms to simulate the effect of blasting in different rock types

Feb 1, 2020

By Neal Lee

Often the effects of wet boreholes are not taken into consideration when designing a blasting program to exhibit a certain amount of explosive energy per unit of rock such as design by powder factor, expressed in lbs./bcy (pounds explosives per bank cubic yard) or kg/bcm (kilograms per cubic meter), often the effects of wet holes are not considered. This paper examines different methods of loading wet holes and the effects they have on actual explosive quantities/unit of rock. In particular, we are looking at the amount of water trapped within the explosive column (bulk loading from the collar), or the annular space left void of explosives product around and between cartridges (wet-bags) with many of the current wet hole loading methods in use. We will focus on the effect this has on actual powder factor relative to “as designed” dry hole loading values, as well as the effect on performance of the explosives.

Jan 1, 2011

By Mario Dobrilovic, Zvonimir Ester, Vinko Skrlec, Vjecislav Bohanek

The first public garage in the city of Dubrovnik has been built in highly urbanized area, on location Ilina Glavica. The excavation of the building pit has been done partly by construction machinery, i.e. by hydraulic hammer for excavations and partly by drilling and blasting. In the vicinity of the building pit there are houses, buildings and two schools. Drilling operations and blasting have been performed during the working hours while regular school classes have been held and activities in other buildings took place. The nearest structures are some 5 to 10 meters (16.4 to 32.8 ft) away from the building pit, which makes it even more difficult to perform blasting operations in the urban environment. For the purpose of determining safe and permissible oscillation velocity limits, i.e. the proportion of seismic effects of blasting, a trial blasting has been conducted. The permissible mass of explosive charge has been determined by original method respecting the requirements of existing standards (ISO 4866, DIN 4150, US BM 8507), which determine the permissible oscillation velocities in relation to their frequencies. According to measuring results of the oscillation velocity during the test blasting the design parameters of blasting field have been corrected and zones have been established within the excavation area considering the possible effect of blasting to the building pit environment. Further blasting operations have been performed in stages, in smaller blasting fields with deck charge within a blast hole while respecting the requirements of the transport possibilities for the blasted rock mass within the building pit and performance of control measurements of oscillation velocity for each blasting. Through application of all the protection measures, design solutions and systematic control of performance of activities the complete excavation by blasting has been completed without any damage on neighboring structures/buildings. This article presents these solutions and methods for reduction of seismic impact of blasting to the environment.

Jan 1, 2009

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By John C. Brulia

The IME member companies, the ISEE along with its chapter organizations, the Federal, state and municipal regulatory agencies, and the industry consultants and suppliers have developed safety equipment, provided safety guidelines, promulgated safety-oriented regulations, and conducted safety training for blasting personnel in an effort to reduce explosives-related accidents.

Jan 1, 1994

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By Bob de Raadt

The main problem in blasting a fly-over spanning a main road is the brief time available for blasting and the removal of the debris, in order to minimize the ensuing traffic disruption in the public highway below. The blasting plan is consequently based on an extreme "time is money" concept, in which speed and public safety are predominant factors. This paper discusses reliable blasting parameters for this type of demolition.

Jan 1, 1984

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described

Feb 1, 2020

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010