Search Documents

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Jikai Rong Changai Liu

The dig instrument by blasting is a,new product we developed(See Fig. 1) It is an apparatus to dig hole at the ground. It is composed of combustor A, combustor B, charge pipe and shock head. Work characteristics of Combustor A are that combustion time is 1. 5 seconds, driving force is 725kg. Work characteristics of combustor B are that the combustion time is 1. 3 seconds, driving force is 460kg. After the combustor is ignited, the charge pipe is drived into ground immediately. Then, whole dig instrument is threw out automatically, but explosive in charge pipe is left in ground and blast in the twinkling. The diameter of vertical hole formed by blasting is 3cm to 60cm which is controlled according to engineering requirement. The maximum depth of the hole diged by using the dig instrument is 2M. It applies to blindage of single solidier in military affairs, and hole planting pole as well as sewer in civil use and so on. The two shots are charged in combustors to dig a hole. The maximum weight of shot is 490g, minimum is 130g. The whole process diging hole is completed automatically in about ten seconds.

Jan 1, 1998

By Diane F. Baker, Cathy Aimone-Martin

A series of small-scale explosive experiments were conducted in a perlite mine near Socorro, New Mexico. These experiments were a joint effort between Los Alamos National Laboratory, New Mexico Institute Of Mining and Technology, Southern Methodist University, and Defense Nuclear Agency. The purpose of these tests was to measure the changes in the shock wave and seismic coupling as a function of depth of burial and structural setting. The size of the explosive charges ranged from 1 to 68 kg. Over 1150 measurements of velocity and acceleration were made on thirteen experiments using three component sensors. The sensors were placed to maximize the azimuthal coverage as well as to provide data at a variety of ranges from ~1 to 130 m A few far field measurements were made at ranges of ~2Êkm. While the bulk of the measurements were made on the surface, high g accelerometers were placed in one instrumentation borehole to provide some free-field measurements. Preliminary results indicate that significant differences in the amplitudes of signals can occur when the location of the explosive charges are changed by only meters. Part of the observed difference is attributed to variations in the rock immediately adjacent to the charge affecting the shock coupling; and part to the effects of the site characteristics.

Jan 1, 1994

By Ravi Sahu, Brad Gyngell, Oktai Radzhabov

Design machine learning approach to simulate the process of muckpile throw distribution before blasting.

Feb 1, 2020

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Jaak J. K Daemen, Clayton R. Morlock

A study was performed to evaluate the predictability of airblast overpressures induces by production mine blasting. Thirty-seven production blasts were monitored using 3 blasting seismographs giving over 100 blast overpressure records. Blasts were monitored at 5 coal highwall operations and at a limestone quarry, all in the midwest. Blasts consisting of small surface charges were monitored to permit an assessment of prediction methods under controlled conditions, as well as to observe actual delay intervals and their influence on the overpressure.

Jan 1, 1983

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976

By F M. Dantini, P Berry

An experimental investigation on the trend of cratering induced by explosives placed on rock masses was carried out. By using various types of explosives and rocks having different geomechanical parameters, it was possible to evaluate the influence of the explosive-rock coupling. Furthermore, the importance of the parameters defining the rock and the explosive for the absorption of energy induced in the rock mass, is pointed out.

Jan 1, 1981

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By Trevor Ames

Highwall instability, and sometimes referred to as ground failures, historically are a consistent contributor of mine injuries and fatalities within surface mines. To combat this several efforts, including those from NIOSH (CDC), to educate the mining community with insightful literature focused on hazard recognition and advances in ground monitoring systems have been performed. The question is can more be done or is this our last line of defense to manage potential dangers? Is there a more effective method to reduce hazards presented by ground failures including rockfalls?

Jan 1, 2015

By Dave Harrison, Phyllis Hasser, Ken Eltschlager

The beginning There was the video:– “Understanding Vibrations from Blasting” – 2002 to 2004 in development – Dale Ramsey ad hoc Public Education committee chair – Available At the ISEE bookstore Public Education and Public Relations Committee • Standing ISEE committee 2004 • Co-Chairs – Ken Eltschlager, Dave Harrison • Purpose: "Develop and conduct programs on public education and public relations. Public education programs will focus on public awareness, understanding, and appreciation of the explosives industry. Public relations programs will concentrate on providing blasting professionals with the tools to assist in the public's understanding of the explosive industry and in the appropriate ways to respond to local community issues."

Jan 1, 2007

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By Stephen Chung

The quality of a blast design can be evaluated in many ways. It may involve fragmentation, muck profile, environmental effects in terms of vibration and the excavation of the blasted material. To assist and ensure an achievable cost effective design, numerical modeling techniques are often applied as part of the operating procedure. While excavation is one of the mining operations which has a direct influence on the bottom line cost of productivity, the characteristics of a pile of blasted material deserves a closer look in terms of diggability. This paper reviews the current diggability techniques available for application to the blasting operation. To help better understand the involvement in digging, this paper also introduces an evaluation approach based on a discrete element method. The model presented in this paper deals with many variables that are considered to directly affect digging. They are the density and cohesion of material, fragment shape and size distribution as well as the swell of a muck pile. To help visualize the analysis approach, sample runs and animations are given in the paper to show the setup of muck piles produced in bench blasting as well as in sub-level caving. The computed forces experienced by the bucket during each mucking cycle are also discussed.

Jan 1, 2008

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017