Search Documents

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By Rudolf E. Greuer

This study concerns itself with two topics of the mine ventilation - mine fire interface which, when the work for this study began, did not seem to receive sufficient attention. Section 1: Comments on Spontaneous Combustion of Coal in Mines It is attempted to describe heat generation, heat and oxygen transport, in such a way that existing experimental data for U.S. coals can be used to assess conditions inducive to spontaneous heatings quantitatively. Investigated are, in particular, critical air velocities, minimum sizes of coal accumulations, moisture contents and the influence of mining factors. An extensive, practice oriented literature survey is included. Section 2: The Early Detection of Mine Fires by Assessment. of Mine Gases The suitability of the major constituents of combustion products for an early detection of fires is discussed. The same is done for gas concentration ratios. Since it was felt (at least at the time when this report section was written) that the value of the carbon monoxide/oxygen deficiency ratio was overestimated, the usefulness of monitoring this ratio as compared to monitoring CO concentrations was critically investigated. The state of art concerning instrumentation and organization of fire detection systems is reviewed also.

Jan 1, 2011

By Lewis M. McNay

The strength characteristics of hydraulic sandfill modified by varying quantities of type III portland cement and two flocculants were investigated by the Bureau of Mines. Three different sand-cement ratios were examined using different percentages of flocculant. Two other experimental variables were curing time and weight-percent solids for hydraulic mixture. Results of unconfined compression tests with strain are discussed. Maximum strength was achieved with 0.5 weight-percent of ferric sulfate per ton of solids when the slurry mixture was 75 weight-percent solids. The bearing capacity of hydraulic sandfill is reduced by increasing the water content and decreasing the amount of cement mixed with sandfill.

Jan 1, 1976

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By Noel N. Moebs

The U.S. Bureau of Mines is conducting research on many topics relating to the mineral resources of the United States. This is done to ensure an adequate supply of minerals essential to a viable domestic industry and a sound economy. The United States is almost totally dependent on foreign supplies for a number of minerals such as chromium, niobium, tantalum, and manganese for which there is no available substitute, while many other minerals such as titanium are abundantly distributed throughout the earth but seldom occur in adequate concentrations or useful forms. This report describes an example of a small but high-grade occurrence of titanium are in Nelson County, VA. This occurrence could be exploited under favorable economic conditions with new mining technology such as borehole slurry mining. The report demonstrates that the dikes at titanium ore, a mixture of ilmenite and apatite locally termed nelsonite, can be detected and traced along strike using magnetometer traverses. This information will aid in the selection of appropriate slurry borehole mining test sites in the area.

Jan 1, 1993

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

By R. S. Dean

The original flotation reagents were certain oils selected for a combination of properties that occurred fortuitously. It was recognized quite early in the study of flotation mechanism that, in order to function, an oil must have an active group-one that differs from the remainder of the molecule in its affinity for water or the mineral particle. Wark4 gives credit for recognition of this elementary chemical principle to the senior author of this report.5 However, it was soon found that simple hydrocarbons could not be used as flotation reagents and that two of the functions, which were combined in the early flotation oils such as pine and eucalyptus, could be obtained in separate compounds and their relative intensity controlled to advantage. These two functions were called collecting and frothing.

Jan 1, 1944

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By F. S. Kendorski

This report presents the results of a program to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies' are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1981

By Frank L. Hess

"New England" and "granite" if not synonymous are at least associated terms. Where there are granites that are not deeply eroded there are usually pegmatites, the most erratic of rocks, and of them New England has a full portion. Many of the New England pegmatites contain the rare alkalis - lithium, rubidium, and cesium. however, the same in homogeneity of the earth's crust that has made the New England pegmatites unusual, in that so many of them contain the rare alkalis, has likewise made the distribution of the rare-alkali minerals sporadic even in those pegmatites, and most contain only enough to furnish collectors with more or less ornamental and uncommon minerals. New England has long had numberless collectors of minerals, and the mineralogists of its various schools have published many papers on the pegmatitic minerals, including those of the rare alkalis, but none of the papers have dealt with estimates of quantities. In this paper we have tried to place the emphasis on quantity rather than on mineralogy.

Jan 1, 1943

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By Peter Grandone, Ludwig Schmict

The injection of oil-field brimJs into subsurface formations containing mineralized water ·now is .recognizud as the most satisfactory and effective means of disposal in Kansas.· Other disposal ·methods, such as impounding brines in evapOTation nonds and controlled diversion into surface streams, have not prov-ed entirely successful, principally. because the volumes of brine to be disposed of were large, the soil f;?xtr~~mely porous, the net evaporation is low, and the rairiiall insufficient fc)r adequati.:~ dilution of the brine. The disposal of brine by subsurfaCE) inj'ection is often: more. expensive than by either of the above surface methods; nevertheless, surface dis:pos?,l ow.ing to the damaging effe-c.ts of· salt water to plant, animal and aquatic life and to potable water supplies has been:a long-continuing problem with many technical, economic, and 'legal·complexiti,2s

Aug 1, 1943

Develop a new technique of in situ rock stress measurement which can be used when and where the conventional methods, such as the overcoring stress relief methods and the hydrofracturing method, cannot be effectively applied. Approach The Bureau of Mines developed basic principles to determine existing biaxial stresses in rock mass by using an instrumentation package consisting of one 3.8-cm-diameter hydraulic cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated flat hydraulic borehole pressure cells (BPC) to he installed in a single drill hole.

Jan 1, 1988

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929