Search Documents

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled predominantly by rising personal consumption expenditures as well as growing government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the minerals-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The low level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1987

By E. P. Youngman

From a scientific point of view , the zircon is by far the most remarkable of the gem stones , and a satisfactory solution of the problems offered by its characters and constitution has not yet been made . 3 Three distinct forms have been recognized , differing in specific gravity , hardness , optical properties , behavior when heated , and color.4 ( See section of this paper entitled "Description and Properties . " ) Zircon as a gem stone has not been as well known as its properties warrant . It is one of the most brilliant of the precious stones (having a high refractive index) . The colorless zircon rivals the diamond in brilliance and fire play to such an extent that a judgment based entirely upon optical inspection might be erroneous . In the opinion of gem authorities , the colored stones likewise have much merit . The blue zircon ( " Starlite" ) was so named by Kunz because of its resemblance to a " star twinkling in the night . " Another gem authority describes the leaf- green stone as one possessing a restful beauty , the red stone as having a certain ( though somber) grandeur , and the golden-yellow stone as being unsurpassed in magnificence . The slowness with which the zircon , a stone frequently mentioned in ancient literature , has come into use in modern jewelery may be owing to the fact that authorities differ as to whether the colorless and the blue zircons are found as such in nature or are treated stones . Any treated stone , although the material of which it is composed may be essentially genuine , has been considered a deception . However , according to Kunz , " Starlite is now sold over the entire world ; never has anything been so well introduced. "7 Dr. Foshag, mineral curator of the United States National Museum, states that the first allotment of zircons to enter the United States was obtained in 1921 from Siam ( through France ) for scientific or museum purposes and that four or five years later the stones were adopted by the jewelers of this country . Retail jewelers are displaying the colorless type and the blue stones , especially , in finger rings , necklaces , and like ornaments . Fine crystals have been used somewhat extensively in jewelling watches and as supports for the edges of fine balances . At one time zircons were though to be appropriate in mourning jewelery .

Jul 1, 1931

By Paul C. Hyndman

The U.S. Bureau of Mines investigations of the three subunits (fig. 1) of the Homestead RARE II area (No. 6291) revealed no evidence of mining activity or mineral deposits in the area. The Iron Dyke Mine, 3 mi (5 km) outside the study area produced ore between 1916 and early 1982 from a volcanogenic massive sulfide deposit in the Permian volcaniclastic Hunsaker Creek Formation of the Seven Devils Group. The Hunsaker Creek Formation does not crop out in the RARE II area, but extends into the area beneath Miocene flows of Columbia River Basalt. The abundant basalt in the area could be used as aggregate or dimension stone, but equivalent deposits exist closer to markets. INTRODUCTION Location and Access The Homestead RARE II area (fig. 1) encompasses 6260 net acres (253U ha), in three units, of the Wallowa-Whitman National Forest in Baker and Wallowa Counties, Oregon. Two small units of 160 and 300 acres (65 and 120 ha) are 5 mi (8 km) north and east of the main study area. Homestead, Oregon, on the Snake River, is about 3 mi (4 km) south of the two small areas, and about 3 mi (4 km) northeast of the main study area. Peripheral access is provided by State Highway 86, U.S. Forest Service Road 39, and ancillary roads and trails.

Jan 1, 1983

"An active list of permissible explosives was published in July, 1930 as part of the United States Bureau of Mines Report of Investigations 3025, under the title of “Active List of Permissible Explosives and Blasting Devices Approved Proir to June 30, 1930”. Changes on that list were authorized in August, September, October and November, 1930, and January, March, April and June, 1931, as published in Reports of Investigations 3029, 3037, 3046, 3053, 3069, 3089, 3099, and 3123, respectively, By these changes the following explosives were added to the active permissible list:Big Red No. 9 Hercogel CBlack Diamond No. 5-A Liberty No 1Black Diamond No. 9 Liberty No. 2Burton 5, L. F. Liberty No. 3Burton 7, L. F. Liberty-Gel L.P.Duobel No. 4, L. F. Wesco Coal Powder No. 1Genigel No. 1and the permissible explosive EP-28 was transferred from the active to the in active list of permissible explosives.During June the following permissible explosives were added' to the active permissible list:Austin Red Diamond No. 9-B, L. F. BurtonAustin Red Diamond No. 9-C, L. F. Gelobel No. 4, L.F.Austin Red Diamond No. 10-A, L. F. Liberty No. 6Austin Red. Diamond No.12-A, L. F. Monobel 8 L.F.,- WR Austin Red-D-Gel"

Jul 1, 1931

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983

By D. C. Seidel

This report describes generic procedures and equipment arrangements for conducting laboratory-scale hydrometallurgical and related waste-management experiments. It provides a starting point for personnel who have received or are receiving professional training, but do not have specific experience in laboratory procedures. With guidance, it also has application as a resource for technician training. The publication contains chapters on laboratory safety, feed-sample preparation, leaching, solids-liquid separation, and recovery from solution.

Jan 1, 1995

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By W. G. Sandell, L. C. Bauerle, K. C. Dean

"INTRODUCTION As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agncies engaged in purchasing and stock-piling some of the more critical and strategic materials. At the request of Dr. Alan M. Bateman, special representative of the Metals Reserve Company, metallurgical studies were made on three samples of oxide tin ore from, the States of Zacatecas and Guanajuato, Mexico. The samples were submitted for testing by A. Porraz of the Financiera Miners, S. A., institution Financiera, Edificio Guardiola, Despachos 500-507, Mexico, D. F.The samples as received were marked Nos. 1, 2, and 3 and described as follows:Sample 1. - Origin: Mining camp ""El Naranjo,"" municipality of Sombrerete, State of Zacatecas, Mexico. This sample was partly concentrated by washing and as received was all minus 10-mesh in size.Sample 2. - Origin: Deposits in Sierra. Fria and Juan Cherey, municipality, of Jerez,State of Zacatecas, Mexico. This sample represented run of-mine ore.Sample 3. - Origin: Mine ""La Frontere, "" Ranch of San Pedro del loya, State of Guanajuato, Mexico. This run-of-mine sample was low in tin content but came from a highly mineralized tin field."

Jun 1, 1947

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.